(PT. 3) 300 Kilometer service on the most HATED scooter on the internet: Living with a Tao Tao

[@gabehodges1088]

Keep it stock!! It can't be a Tao Tao review, which is why this started, if you start putting aftermarket parts on it. I'm all for you adjusting the scooter (brakes, carb etc) but I feel that if you start adding mods it's no longer a Tao Tao review. If you keep driving it stock it can become a long term review. Than you can see what issues arise and when. Just a thought. Great vid, keep it up!

[@jesusoftheapes]

That could be the most boring idea ever ! DO NOT LEAVE IS STOCK !

[@edwardjames6023]

@rick shaw i have no legs and ride a scooter

[@edwardjames6023]

@@jesusoftheapes but he has a point. This isn't about "pumping" your ride, it is about a pure TaoTao review

[@chefkendranguyen]

My opinion is you should keep it stock until the experiment is over. They start messing with it.

[@Scooter_911]

thanks for your input!

[@patriotwarrior_556]

​@Scooter_911 Hey THANKS for your video...I think you should make a short...showing exactly where the drain and fill plugs are...So Manu people are trying to fill the gear box by removing the adjacent support bolt vs fill plug..so many of these are coming with almost zero gear oil because of it...Also..if you could tell us EXACTLY how much gear oil...and not everyone can get the oils you show please show us oils and gear oil people can get from thete local autoa part store.. I think you thought those things would be obvious and they are to the mechanically inclined but to tye average person they have zero clue....or when you check the oil do you screw it all the way down to check and do you fill to top of crosshatch marks.... Please LMK this is fit my son ..I'm gonna link a short so you see what I'm talking about...so much bad info out there...

[@patriotwarrior_556]

​@@Scooter_911kzbin.info/www/bejne/pJ-9e2aBn7WFbJIsi=4BG_31O5814beh73 Look how much gear lube comes out of this brand new bike and looked where he tells you to fill it...also are these like cars you fill until it overflows from fill plug.. THANK YOU SO MUCH BROTHER!!

[@joef.3094]

one doesn't "live with" a taotao ... one buys it because of the almost irresistible price, then starts fixing ... and fixing ... and fixing .... eventually one sells the taotao cheap to someone who also can't resist the low price. thus, the cycle of sorrow goes on.

[@carmineredd1198]

i have a 150 tao, i'll sell it to you for $500 plus shipping and guarantee the engine/transmission for two years unlimited miles , you will have to get a new stud bolt and helicoil for it , it has over 30,000 miles on it

[@DivergentDroid]

@@carmineredd1198 That's a great deal. I'm looking for one locally in the New Orleans area and no one has deals like that.

[@carmineredd1198]

@@DivergentDroid yeah, . there are 2 major problems. first you want a piece of 3/4;; wood strip about 10'' long and tie it under the seat bucket onto the crossbar to keep the plastic side panels from breaking at the connection tabs . 2nd you want to loosen the muffler mounts at the top and at the axle and shim with a washer so the mount brackets don't break from torque. don't force the muffler or it will break at the mounts address these issues before you even sit on a new bike . if you want to mail order , they want $250 shipping so $1000+- shipped for the 150 powermax, there is a new model the Pilot, it has different wheels

[@DivergentDroid]

@@carmineredd1198 Thanks for the info. I'll keep those things in mind.

[@jayinmi3706]

I'd probably leave it stock, but might consider changing jets since it's a budget mod vs. replacing the carb.

[@mopedmessiah]

I agree. Its something a beginner or uninformed buyer could figure out, and requires no tools tools outside of a screwdriver. My scoot actually runs fine lean like that, but these 50s are more tempormental

[@marsrover001]

Go full jank. Rejet with a drillbit. Remember the main buyers of these scooters, just trying to get around town for cheap and literally can't afford anything better. It's why the brake pads were cleaned and torched rather than replaced.

[@mattomite9097]

I agree since most people can pick up new jets easily and cheaply through Amazon. It’s an easy solution and can be done cheap

[@davespooney8472]

Agreed, rejetting is adjusting the carb to the climate - it’s good practice and a good repair shop would do it anyway

[@BigEpinstriping]

@Pony Boy So you're telling him to remove the Pair system from the scooter. won't really affect it much; If he was going big bore, It'd be a good idea, but stock, it doesn't affect much other than run dirtier.

[@cbkenison]

Leave the carb as is until the 1000km service and make a decision then.

[@edoardomancini838]

Rejetting would be ok because is an adjustment and that scooter needs it because seems super-lean. Changing the entire carburetor is a mod and would affect the results of the experiment. Nice video. Keep up the good work!!

[@DanieMations]

^^^^

[@crabjoe]

I'm going to disagree with you. The reason is because the carbs are sealed , so not meant to be rejetted. Due to EPA regulations, all these Chinese products now come with sealed carbs to prevent the average person from messing with them.

[@DanieMations]

@@crabjoe Yeah but, everyone does it so... he could do it aswell

[@edoardomancini838]

I didn't know that cause I'm from another continent. It's a pity because you can't adjust AFR. Also open the sealed carburetor would be considered as a mod.

[@Ishii-kun]

Personally, I would also do what a person with a $750 scooter from Amazon would do, and that is buy a cheap jet kit off Amazon. That way, while still giving the scooter the best chance at life, you're still limiting yourself to the resources available to the kind of person who would buy this scooter.

[@ronaldcolman6211]

I'd start by moving the needle up one position, It's not a mod, but an adjustment of factory parts. I'm sure they ship them super lean to be emissions compliant. As far as the low compression, it might sort itself, but you cant baby these thing or they'll glaze the cylinder. I'd love to see some mods, but I also want to see the experience of running it as it ships. Maybe start mods at the first major failure? I'd like to see some testing of stock vs modified, maybe stages, like big bore/cam. Then carb/exhaust/big valve head. All the mod stuff is dirt cheap from goofit on amazon. Using the cheapest stuff is right in line with the spirit of a frugal TaoTao buyer.

[@forevercomputing]

Compression is always lower when the rings are still open. A warm engine should close them up further.

[@krollpeter]

I am with Ronald. Everything stock, only if something is really not working right then redo / replace. After half of testing or even after the regular test time, then redo / tune to maximize its potential, under economical considerations of course.

[@RellyOhBoy]

No mods or upgrades. Re-jetting the carb is part of tuning/maintenence. Good series, keep it pushing...

[@Scooter_911]

thanks for your input!

[@andystokes8702]

The whole point of this experiment was to see how this scooter performs stock. I'm sure that an alternative carb would improve matters considerably but if you're going to do that you might just as well fit a big bore kit and a sports exhaust and forget the experiment entirely. By all means move the needle a couple of notches and maybe even rejet to stop it running so lean; I would consider these to be adjustments rather than alterations but beyond that I think you are defeating the whole purpose.

[@rickoverink9778]

I'm a mechanic and serviced a lot of gy6 engine's with 20000+ kilometers often. And they ran without problems if serviced regularly. A lot of the time the rest of the scooter will disintegrate before the engine wil stop running

[@jouman450]

My 16 ear old Yiying 50cc has 21000km on it and still runs just fine. Oil change, valve clearance and the right carb jet are essential.

[@lillemormandemand5998]

I love this series, its nicely edit and a fun little intro sound that makes me smile. You are helping me and many others understanding the physics of a moped in a nice way. Keep it tecnical for sure, but im in a conflict about the jetting.. could be nice for some to know how to do it, but probably no regular Tao Tao owners would take it that far. And i dont think you want to drive this thing forever. But, if you do wanna live with this thing forever go for it. You have already expandet the possible life age of your fine motorcycle alot i believe. Im gonna bring my little tao tao back from the graveyard with the good energy you share here on KZbin. Thx for living with a Tao Tao. Best regards - Totte

[@communistdog1274]

Yess ive been waiting for this

[@rockettests2617]

Definitely re-jet the carb. As it continues to break in the lean condition will continue to get worse. I consider jetting to be part of normal maintenance until the motor is completely broken in. Elevation above sea level often makes the jetting a necessity.

[@toddmaples3370]

Cranking rpm is a good record to keep, helps keep track of starter motor strength &/or pinon year binding. As far as running lean, they all run lean from the factory for emissions reasons. I've always replaced my whole carb as it's easier than trying to get in and re-jet a sealed unit. Very technical breakdown, love it.

[@DoRC]

I would definitely rejet. To pass modern emission all carbureted vehicles are tuned nearly dangerously lean. Rejetting the carb is pretty much mandatory a d you're already doing far more than most ppl would.

[@robtindall9939]

Loving this series, I have often asked if chinese bike reliability is 'Nature or nuture'. I think you should keep it stock for the experiment, so adjust or rejet the carb but no mods.

[@Scooter_911]

Great suggestion!

[@leonstancliff7218]

I bought the exact same bike last year. Something for a 70 year old retired guy to mess with. No prior experience with a GY6. Out of the box top speed was 30 and slow getting there. Within 2 days I had knocked the baffles out of the exhaust with a Harbor Freight screwdriver and BFH and had the speed up to 35-40 with no other mods. I watched some You-tube videos, which one would do if they shopped Amazon, and ordered a jet kit for $12. Sealed carb, yes, and it took me all of 10 minutes to unseal it with a hacksaw to slot the screws, and screwdriver. If you have the savvy to set the valves the carb is not even a challenge. I had a 76 main and 30 idle jets. Went to an 88 main and 32 idle, opened the air box and retuned the air/fuel mix. Cruising at 40-45 and I weigh 200. Got that for $12 jets and no other expense. I say go for the realistic low dollar mods.

[@leonstancliff7218]

@Pony Boy That's like telling an ugly chick not to use makeup!

[@Arkoss]

I really appreciate the effort you are putting into this series! Watched the entire thing. It's great learning from your experience, and you are doing a great job documenting it. I feel this would have been of great use a few years back, when I had a 150cc chinese scooter that insisted on falling appart on it's own. At least it teached me how to service my own stuff, as I had to tear it appart about 15 times in 2 years, not counting the dealer services. About the tire wear outlasting the engine: The one I had came with some garbage, absolutely terrible tires with a white band (the scooter had a classic look to it). I sold the thing with about 9000 km on the clock, and the rear tire was starting to show some real wear signs. It was all teared up in every groove, it even deformed itself because of a gas station air pump that decided to lay 45 PSI on it, massively overshooting the 30 I had asked for. I think the tires had about 2 or 3mm left before it sold. But you know what? I had seen before that the frame was kinda crooked (yes, the freaking frame was bent). So, the bike had to be a bit sideways to go straight. Maybe that precipitated the tire's wear! By the way, the bike had absolutely 0 crashes or drops. I'll never know for sure how the frame got to bend that bad. I sometimes carried a passenger, and of course I went over some awful bumps on the street, but nothing too out of the ordinary! Anyways, I'm glad you are doing this for people in the same situation I was to use! Thanks for taking the time to do so :D

[@glenndoiron9317]

The frame is usually steel, if you didn't hit potholes or do drops, it was probably shipping damge.

[@marlowegrau6028]

Very good info. Thanks for offering up to share the spreadsheet. I do most of my own work and would welcome this option!

[@Riddle6EOS]

This series is great! Been waiting! I dont own a tao tao. But we have many chinese scooters here in Europe too, with diffrent names but they are the same. But it would be fun to put up a test just like yours with an used one. PLEASE share the docs! Would love it for a potentiel project!

[@moonliteX]

this might be the best scooter series ever

[@Scooter_911]

@@moonliteX thank you very much my friend!

[@peterhallbus1114]

A jetting-kit is really cheap and realistic to upjet it a little, starting to replace working parts like the whole carb perhaps not so much (coz in many countries also illegal unless it is a stock size).

[@peterhallbus1114]

@Pony Boy Caps-lock much? changing idle mixture won't do much for running lean on max throttle, wich is what you use most on a moped.

[@mattparker9726]

YES! MOD the heck outta it! I would like to see what "performance" parts you consider good. These parts are all super cheap, and it made it difficult for me to determine which ones were any good, not being a mechanic myself.

[@davidroberts6594]

No mods! Drive it till it breaks, maintenance by manual recommendations, keep it fair and with stock parts, maybe carb adj as any engine should have this checked anyway.

[@mozzer8234]

Your videos are so amazing. I'm about to be receiving a clone of this scooter from my uncle and my main worry was the lack of information on parts and how to perform services given many mechanics where I live only work on bigger brands. I'm going in with a lot more confidence that I can make this little machine shine now!

[@LILEmusic11]

Im glad you're following a progression with your data points, keep up the good work

[@Scooter_911]

Thanks!

[@LILEmusic11]

We love you Garrett, thanks for grinding after the grind for us

[@Scooter_911]

Man, thanks! I appreciate you appreciating that!

[@LILEmusic11]

@@Scooter_911 I would really appreciate some pointers fixing up my 2000 honda helix, I changed oil, filled coolant, it is dying after warming up when at a red light at idle, seems to sputter about 30mph but picks up to higher speeds fine, after dying it is hard to start

[@chuckvt5196]

I think rejetting is cheap enough, but I would not do much else. Try and leave it as stock as possible, and let it live or die on its own merits! Great series!

[@ShipWreck54]

The goal should be keeping it as stock as is practical. That being said, being practical often dictates making necessary upgrades. If running lean is an issue then it needs to be addressed, starting with the cheapest option and scaling up until the problem is resolved. I’m the person you are making this video for, someone willing to work on their scooter but not a master mechanic. I can figure out a lot of things but I’ve never rejetted a carb. As for the biggest problem with scooter owners being they don’t replace the shipping oil right away, the problem is much worse than that. They only change the oil every 3,000 miles because that’s what they’ve been told to do by their car owning parents, then blaming TaoTao when the engine blows! 3,000 miles, that’s almost 5,000 km! And it’s often 5,000 km on the shipping oil! THAT is the #1 reason these things fail prematurely in my opinion. Failure to keep bolts tight is another big issue. I’ve learned to use lock-tite and recheck bolts often. Nothing like a brake caliper falling off to get the riders attention, lol. Some issues you WILL have with this series of videos are bolts loosening up surprisingly fast, petcock failure, worn out sliders, rubber hose failures (both vacuum & fuel lines) and a slew of electrical problems. All in the first 6 months. The engine itself will likely be the least of your worries.

[@j-bolo6637]

Bigger carb would really free it up, but staying stock is the best test for engine longevity, just a correct re-jet to get it fuelling right👌🏼

[@Scooter_911]

Great point!

[@tonnilerche]

White dry thin smooth coating on spark plugs today, is due to modern additives in the fuel, put in from the refinery. Yes sparkplugs would normally look brown, but the pictures used for evaluating spark plugs are outdated by 20-30 years.

[@miketayse]

I'm reallying enjoying the project. I'd keep it stock and just adjust. Doing the spread sheet is a good idea. Looking forward to the next episode! You have the only notification on KZbin I get and watch ASAP. Keep up the great work!

[@itsmephil2255]

Loving these videos,can't think of anyone else doing this kind of review Looking forward to the next video

[@billrimmer5596]

Leave it stock. Interested in the compression as motor breaks in. I love all the recorded data. That way we have known good. The needle position rather than the main jet would determine the color of the spark plug. If it’s like a motorcycle carb. I’m pretty sure that u r not wide open throttle all the way home. I know u have to pace yourself on video output. I really enjoy them. My Buddy 125 runs great. I’m going to do the oil changes. And I need to replace one way starter clutch. I will order off Amazon unless u have other suggestion. Also, a valve adjust. Raise needle one slot. Maybe? What is your day job wrenching. Thank u!!!!!!

[@zealandboutin2494]

just rejet so we get a full out of the box what to expect, thanks! I love the series keep up the good work!

[@Test-gb6xx]

Please don't mod it. I'm most curious about how the scooter holds up as it was shipped... I'm not curious about rejetting, or modding because I wouldn't do that myself anyways. Your video interests me because it's like a scientific test of how long this POS can last if giving the best possible care. Once you start upgrading and re-jetting, then it becomes just like all the other scooter upgrade videos on youtube.

[@anonymoose6873]

I've had the TaoTao pony 50 for 3 months now and I've done an 80cc big bore kit and a 20mm carburetor and I'm completely in love with it. Now I ordered a icebear maddog gen 4 49cc ruckus clone just for fun

[@C0d0ps]

I just got a yamaha jog r 50cc and don't know anything about mechanics but love this series hope you continue with it the full 6 months 💜

[@Scooter_911]

OH MAN I LOVE the yamaha Jog. Great buy! much much MUCH better than this cheap little scoot. Happy riding!

[@zrobotics]

Can't say anything about recovering brake pads with that trick (have never needed to), but I have used that trick on a clutch. This was a temporary/junkyard type repair on a 62 IH Scout, but the clutch is still working good after ~15K miles, and this clutch was horribly oil soaked. I soaked the clutch in gasoline overnight to allow it to fully penetrate the friction media, then lit it on fire. NOTE: Don't just let it burn off all at once, that will definitely overheat things. I let it burn for around 30 seconds, then smothered with a cement board. Allow the clutch to cool, then repeat until it won't burn anymore. It was worth it on this vehicle, since installing a new clutch would require turning the flywheel, and I wanted to preserve the flywheel as long as possible (Plus, clutches for that are very expensive). On something like this, I doubt it's worth it, unless you really don't want to wait for parts. Although the way you did it likely wasn't enough to do much, they will need to soak for at least a couple hours (they will actually burn if they are soaked).

[@film49uk]

This is a interesting test of this small cc scooter ,and will show how good it is with proper servicing and maintenance and how long it goes before some think breaks etc ....keep at it await next update clip ..........................

[@urbexgamma]

I got the same chineze scooter but mine is called Baotian. Driving it 13 years now without any service. (only new oil every year)

[@bluemoondiadochi]

to answer your question on lean mix: Yes, DO adjust the carb mixture, but do not re-jet it! since carb adjustment is just ADJUSTMENT, it's OK, but re-jeting it is already modding and this means it's not stock. so, adjustment is welcome. plus, you're expected to to it at different times of the year anyways to keep it optimally running. try turning it 3.5 turns out. does wonders for my scooter (which is essentially the same scooter as you have). respect for you driving with stock adjusted carb, i couldnt handle the slowness... believe me, with 3.25 or 3.5 turns out its not the same scooter!

[@ThePike4401]

Please continue to test as it comes.

[@ufooooooooooooooooo]

Definitely thinking with the leaving it stock crowd. The experiment was for keeping it up to spec as best as the original equipment allows because the Tao Tao itself is being tested versus the owners. But mods after a major failure was a good idea.

[@Scooter_911]

Totally agree!

[@mysticvirgo9318]

hm agree with the others, rejetting is not cheating :) adjusting the accelerator needle is also acceptable. watch for the o-ring between the muffler and the exhaust pipe . they are a well known failure point. is fair to replace with a proper aftermarket gasket. will not change reults of test ..

[@gerokron3412]

Very nice video series. Recommendation for further data you might consider saving: fuel consumption oil consumption top speed acceleration 0-30 (it does make 30, right?) Best regards

[@thubb3628]

Just bought a scooter. That Google doc would be great for reference. I my 150 in the crate. I didn't know I had to other parts that will already put together when I had received it. So my exhaust ended up rattling loose at 50 MI. Now I know I need to go over the whole scooter.

[@larryshaver3568]

you raised a very good point, if you let the tire treads get too worn it will put wear and tear on the engine

[@MrTrevorkemp]

There is a way of adjusting you or air fuel ratio sort of and if you are going to try to mimic with people who are buying a cheap scooter like this are doing most of them would only do the air Fuel ratio adjustments they would not bother rejecting the carburetor there is videos on how to do that that you can watch on the internets yours is probably sets from factory to be in one of these slightly leaner positions in the 1st place and depending on what parts they had available for the diaphragm needles you'll either have a needle that has 2 points of adjustment on it or 3 points of adjustment and you just want to adjust the diaphragm needle to the point of adjustment where the diaphragm opens up and it opens up a little bit better fuel flow to the carburetor that is how you adjust the air fuel ratio on these machines and if you are still running too lean then go up 1 jet size on your main jet and adjust it that lay but try to do it in a way where it would be more like what somebody who is not very mechanically inclined would do and to just adjust the diaphragm needle and open it up more to give you more fuel and if you are running lean you will probably in this instance noticed a difference and power or maybe you won't notice a difference at all and it will just run a little bit richer Also keep in mind sense this is a carburetor did air cooled vehicle it is going to run hotter than a water cooled or fuel injected engine which means that you should probably be running premium fuel and at which most people who buy these things who do any experiment in around with that find that they get slightly better performance on premium and they generally prefer to run premium that has been my personal experience because they prefer the slightly better pick up and acceleration and the slightly improved top speed from running premium unleaded fuel versus regular unleaded fuel and that does make a difference as well so if you're running regular unleaded you might end up running premium from now on and you can probably feel a difference and how it runs within 15 minutes and you will probably notice that the ween condition noticed on the spark plug will not be as noticeable or might even disappear altogether But do keep in mind you did by this to be a budget scooter and you are going way above and beyond for what 80% of the people who buy this thing are going to be able or even willing to do as far as all of the other little maintenance things that your checking and adjusting so try to keep everything you do as cheap and as simple as possible taking the carburetor off and rejecting it is not one of those things that most people who buy this thing are going to do and in most States in the US there isn't even shops that will touch these Chinese scooters so it's completely up to the owners so try to keep it to simple basic maintenance things and stay out of the slightly more complicated things sense you are actually doing this series to show people how to maintain the scooter as well as how good the long Gemini of these scooters are That being said I did know one person who had 1 Of these Chinese scooters from this same manufacture he was a little bit more of a tinkerer and he had 20000 km on his and was on his 3rd set of tires and he said it still ran great But that was a 2000 and 8 in 2009 new rules were passed forcing new admissions requirements that these scooters met and it also ended up hindering the build quality of these scooters and people who had 2000 and eights and then but brand new ones in 2011 say they noticed a huge difference in performance both acceleration and top speed wise between the older generation of these scooters and the newer generation of these scooters and they said it was quite a noticeable difference.

[@elementalblaze79]

I say, "Give it it's best chance!" Re-jet it due too that is the lowest cost(time is money) but it will make sure the engine is running correctly! If you get a new carb, you'll might run into other troubles that might cause the engine to fail more easily if not tuned correctly, or if it falls out of tune!

[@Scooter_911]

thanks for your input!

[@Rich.Fishing]

I got a tao tao 50cc the factory grinds the heads off the carb screws making very difficult to take apart so I bought a new carb

[@UncalBertExcretes]

Anyone who only gets 10k from one of these engines should quit engines. The engine is not the weak point on these scooters, infact the engine is probably the most well made part of a chinese scooter. Plenty of GY6 50cc's out there with 30-40k on the clocks.

[@glenndoiron9317]

Not so sure of that. I had a 250CC clone a couple of years back. It eventually had a top end gasket blowout (exhaust blowing into coolant). I decided to just replace the entire top end, instead of just the gasket, since the top end kit was so cheap (~$60 IIRC), and doing the full thing isn't all that much more work. When I disassembled the top end, there were no crush washers under the cap nuts for the 4 bolts holding the top end down. I was using the Honda service manual for the motor, which explicitly states to replace them , but they were never there to begin with, so I was a bit confused... until I torqued them all down, and discovered two of them were still wavering under the torque wrench! The nuts had not seated on the top end before they bottomed out on the rods, so I installed the missing crush washers and everything torqued down ok. This was probably why the gasket had blowby, although to be honest it was a 2nd hand bike and I have no idea if the previous owner had wrenched it (I didn't think so because it only had 125 miles on it, but you never know). I probably stripped 3 or 4 bolts on that bike because I was using the torque settings in the honda manual, instead of looking at the steel grade and diameters of the bolts that were actually installed. Trust me, they do cut corners on these engines to make them at that price point. I was fortunate enough to be able to go into a Fastenal to get good bolts (due to my job); otherwise I would have had to mail order them from McMaster-Carr or similar, since these grade of bolts aren't carried at Home Depot or even your local hardware store.

[@dangerouskoin4874]

I have a second hand Roketa 150cc with GY6. I just put 1000 km on it in 2 months. All I have done to the motor is a valve adjustment and it runs excellent. I think the real downside is the plastics and electronics. I need to adjust the steering as well as it has got a little play in it now. Front brakes grab well but squeek arent very smooth in the handle, probably need to check the oil. For $650 I'm really happy lol. Great series!

[@ultraflightamerica9019]

something I thought of keeping track of: suspension droop. you aren't really a small guy; so measuring how much the suspension drops over time would also give an indication of how long the stock suspension parts last. as far as Mods go: I think it would compromise the experiment.

[@johnwhite3346]

HI MATE CAN YOU HELP ME IV GOT SAME MOPED YOU GOT AND I WANT KNOW WHAT BEST ROLLER WEIGHTS I NEED FOR 49CC MOPED TO GET UP BANKS AND HILLS QUICKER THANK YOU CAN YOU SHOW ME IN ONE OF YOUR VIDEOS AND ALSO PICK UP MORE SPEED THANK YOU ALSO CAN YOU TELL ME WHAT'S BEST LED BULBS FOR FRONT HEADLIGHT TO MAKE HEAD LIGHT MORE BRIGHT ON DARK NIGHTS SO CAN SEE BETTER ON DARK ROADS THANK YOU PLEASE KEEP POSTING YOUR VIDEOS

[@gilmendoza8092]

Yes please share the spreadsheet I started testing my own taotao thanks to you

[@blitzkriegh1h3]

I've been waiting for this!!

[@alishaburton7444]

1 year ago I bought a BMS 150cc. It was my daily rider. It has 11,000 miles and runs strong. Belt & variator must be changed every 4,000 miles, clutch at 12,000. I get 60mpg. Tires replaced every 6,000 miles( $50 per tire). Upgraded now: bigger bike. All this is FYI. Anything will last if taken care of. Valves do need a lot of adjusting.

[@gedas3419]

Performance *FOAM* filter with the elbow on the side and upjet to 95 and C-clip to highest position.

[@kkkiiif]

Hey bud! I’m actually doing something similar, I picked up a 2018 wolf blaze 2, the 150 cc variant. I would adjust the carb, and not rejet it since they were designed for “one size fits all” use. Readjust the fuel to air mixture by adjusting the needle and see how that pans out first. I had a similar problem that it was set too lean from the factory. Mods are fun but I’m curious how well these are designed as a personal commuter vehicle, not as a project.

[@glenndoiron9317]

The fuel-air mixture screw in these carbs usually only impacts idling. The throttle body taper adjusts low-mid speed, and the jet affects mid-high speed operation. I'm assuming that these (GY6 50cc clonse) are using the ancient carburetors and are not the constant velocity types you usually only see on larger scooters.

[@kkkiiif]

No there should be on the needle itself, adjustments inside the carb.

[@kkkiiif]

I’m talking the float height adjustment to allow more fuel in from the bowl which should make it overall richer

[@kkkiiif]

Unless I’m out of my league here and there’s something I don’t know about, it’s just an adjustment I’ve made on my 50cc as well as my 150

[@BigEpinstriping]

@@glenndoiron9317 No, they use CVK carbs with a diaphragm

[@dysklexia]

Jetting, for sure. Other reviews say the Chinese bikes come lean from the factory. Its an absolute necessity to put larger ones in.

[@jordancogjurovski6350]

Put big bore kit at 1000km you will fall in love in the scooter. I drove 5000km on 50cc original kit and 15.000km with the big bore kit .crankshaft is strong dont worry about it. My scooter is on the third top end kit(piston cylinder ) botom end is holding strong after 20.000km

[@Scooter_911]

thanks for your input!

[@julianbrizuela]

I was waiting for a new video, I thought the bell notification wasn't working 😂

[@luciengraves6452]

I wish my Tao Tao was a "project." This Tao is my only form of transportation. I bought it with stimulus check. I never got an owner's manuel. With only 1500 kilometers the starter went out. I had to pay 70 dollars for new starter, so I am 770 dollars into scooter now. My friend has a 2015 model with 16,000 kilometers and no problems. I hope I at least get two years out of it. Thanks for info.....

[@w_callaghan8300]

i lived with that POS for 8 years and 32000 kilometers. it lived mostly in the garage scattered around the place in tiny pieces because it was broken all the time. sold it at the price of scrap plastic like it is and bought a suzuki lol

[@JulitoPapitoo]

That google doc spreadsheet would be very valuable information for diy'ers thank you!

[@budhatt5043]

Im getting a Tao 150 powermax in a couple weeks. Very helpful series so far here. Even tho u have a 50cc im sure its essentially the same lists and troubleshooting

[@stevehill4615]

I think leave the machine stock (as someone without knowledge of options available would do) but consider adjusting the carburettor (idle mixture and can the jet needle be raised on the needle grooves).

[@ErmaTheKitteh]

I had well over 28 000 km on the 2 years i had my 50cc scoot, tho after 12 000 km, the rest of the milage the bike had a 72cc big bore kit installed etc, never gave up the ghost :) i did have to change the crankshaft due to bearing noise, but nothing major :D i wish scoots werent so expensive to insure over here ( same insurence rate regardless if you're 15 ( scoot riding age ) or 60+ haha. Did go through the original tires after about a year, but they were so useless in the rain, lasted a long time but not worth the danger they were.

[@Guitargasm1000]

It's not a real-world experiment if your modify it. Also. Like to see you ride it. Helmet cam?

[@Scooter_911]

thanks for your input!

[@saddamespinosa4859]

Keep up the good work

[@steves1007]

Great series for those of us with these cheap Chinese scooters. Please share the Google Doc.

[@danielr.schafer9504]

I don't know about fire but I do know that we used apply some sandpaper on a piece of glass and sand away a couple of thousands of brake pad material seem to work pretty well!

[@xcaliber7779]

Keep it stock until the end. Would like to see how it disintegrates on itself.

[@Scooter_911]

thanks for your input!

[@45AMT]

I've always heard these are jetted lean from the factory for emissions. Not sure if it's to the point that it would damage anything but anything is possible. I've re-jetted the 2 that i had and it made it more responsive

[@toddstidham8374]

I'd say jetting should be fine. Since you are "testing" it as any normal person would use it, it's not unreasonable to think the shop they take it to might not suggest the same jet change (if they are a good and thorough shop that is). But I'd leave everything else as stock as possible for the duration of your test.

[@Ouch.]

No mods please! Keep it stock but adjust it and look after it. I desperate to see when/if it fails.

[@Scooter_911]

thanks for your input!

[@thestonegateroadrunner7305]

Why is it the most hated Scooter on the internet? We had it 3 years, almost no maintenance, 15000 km, it worked perfectly. Was sold for 70% of the new price after 3 years. Best Scooter ever.

[@jarikinnunen1718]

It is good if it is your on expectation level. How many can reach your level?

[@thestonegateroadrunner7305]

@@jarikinnunen1718 It was very cheap and started everytime it was needed. What else could you ask for?

[@speedphreax]

I have put brake pads in the dishwasher to degrease them. Works great!

[@grandpaseed]

for the purity of the test i would try adjust first (carb) and maybe inspect the jet for defects and replace if necessary . As for the data sheet all dependable info is valuable (i have a couple out in my shop that will be needing testing soon to get them back in running order not the same as yours but a base line is always handy. thanks

[@carmineredd1198]

i have a taotao powermax vip 150cc. $650 NIB . i changed the engine oil after 25,000 Miles. still has factory transmission gear oil, belt, brakes et cetera. replaced rear tire for offroading to a Maxxis 6024 120/70-12 . this bike has two major but simple to fix problems, exhaust and plastics . I was impressed so i bought another. however the old one i stripped one of the exhaust stud bolts and the seat bucket is torn the side plastics are broken so the backup will get the knobby tire and become my daily and i am trying to get a new one for a backup . i'll probably fix the plastic side panels and put them on the second one so i can put on saddle bags and not scratch the new plastics .

[@sezwight]

Would be funny to see it properly modified but with budget parts, aftermarket cheap pipe, bigger carb, etc. The sorta stuff that someone may buy for ‘performance’ if they actually buy a scooter at this price..

[@nilswellington3799]

To help perform your exsperiment, I would suggest taking fluid samples during every service on the vechical. Doing so will allow you to monitor wear indicators, as well as see how each fluid is progressing. At the very lest, it contributes data which can be refered to when your coming to a conclusion.

[@nilswellington3799]

To clarify, when I say taking fluid samples, I mean taking samples which are then submitted to a fluid lab for analysis of the fluid's elemental break down which will allow you to see the additive package in the oil, fluid viscosity, Flash point but also if certain elements such as Aluminium, Copper or Iron start to raise in the oil, you can deduce that maybe a component is starting to fail such as main bearings, case being worn into or gears them self.

[@grazz7865]

I have to fully agree with you. When you order these bikes, they come in a crate. You are expected to install some parts and assure everything is working and the bike is safe. Which means you should have at least some basic mechanical knowledge. Otherwise, you’re not able to find things that might have been missed at the factory. For example, on mine the vacuum hose to the petcock was disconnected which means if I didn’t catch that, the bike would have NEVER started because vacuum would not allow the petcock to open and allow fuel to flow. I owned a Yamaha CA50 in 1986. The design and set up is exact the same. Only difference is the Yamaha was a 2 stroke. If you have some basic mechanical knowledge and don’t beat on the bike, it’s worth the money.

[@byronalan8594]

In the "Spirit" of your experiment I'd say that you should run the scooter with it's stock carburetor for now and try using a different main jet. It would cure the lean running of the engine, boost the performance slightly, and, in my opinion, keep your experiment intact, assuming the failures of the Tao Tao style scooters are from stock machines. The carb on your machine was probably tuned for a different elevation than you reside at, so tuning it to run well for your area wouldn't be out of the question.

[@Scooter_911]

thanks for your input!

[@jdrothman]

I vote leave it stock, but do any service you think necessary to keep it running as long as possible. Will be interesting to see how much life you can get out of it. Also would like here a little bit more about your experience riding it with some footage of you riding those twisties :-)

[@complexi8692]

jet is weather specific it may be good for the chinese market but not in the area where you live so adjusting the jet should be no problem. Even when going from summer to winter the scooter would behaviour could change due to air temperature changing.

[@StaitlyNatters]

Be good after 6 or 12 months to comeback and do a session on available mods and upgrades to improve the taotao and if they actually improve the handling, performance and looks

[@philbuilds116]

Tune the carburetor at the least. This is really needed as routine setup. A jet kit is very cheap. I'm very interested in how much more effort is needed by the owner versus fuel injection or 2-stroke engines. I've been debating on the Genuine 2-strokes myself. I still mow with an old Lawn Boy so I know what I'm getting into.

[@Scooter_911]

the buddy 50 is a great scoot. great bottom end so it can take some performance upgrades nicely. Usually i just throw a 70cc kit and set of nice reeds on it!

[@obivaughn11]

If you mod it your defeating the purpose . But chances are you will have to replace the carb because you will.not be able to remove the bowls. My stock had the screw heads removed so I had to replace carb. Runs alot better now though.

[@GoSlash27]

Reminds me of my experiment with the world's most hated scooter: the VietBodge Vespa. I received so much hate from the Vespa community for even attempting it! Long story short: It took a lot of money and effort to make it roadworthy and I don't recommend it *BUT* It's still my favorite and most reliable bike after all these years.

[@AllLifethingschannelyt]

Hi scooter 911 my name is all life things channel YT I just bought this same type of scooter used and the gear oil 10mm screw will not come out with manual rachet and I stripped it a bit what can I do to get it out please let know I'm subscribed to you

[@SE7ENOUSofficial]

Awesome vid! I really like your content and the way you explain things theoretically as well as practically. Can you perhaps make a video of how to fix a kickstarter (on a 50cc scooter) and the possibilities of why the engine won't start by the kickstarter? (I have an Aprilia SR 50 Street Ditech)

[@ericreed9424]

If you’re afraid of it running just a little bit lien. I Would suggest only adjusting the carburetor needle one notch if it has a adjustable one, if not you can buy or find small shims to go under the stock needle head. That way it should keep you good fuel mileage but better performance

[@FLOWGAMING21]

3 best upgrades on Amazon 1.glixal cdi 2. carburetor w/jet upgrades 3. Any air filter that's not stock went with Amazon recommend

[@Scooter_911]

thanks for your input!

[@frankdracman3096]

Keep it stock as much as possible. Re-jet the carb if it is cheep and easy enough to do.

[@jessebonner6189]

Pull the brass plug out of the idle mixture screw port. Be careful about the method though; the idle mixture screw is behind the plug. With the *impeccable quality* of the rest of the bike; it's deffinately part of the lean issue; it should also help make the transition from the idle jet to the main jet a bit more smooth.

[@fixitdaniel]

I would try to mod it so that way it'll perform better but also last longer on rides and maintenance

[@steverolfeca]

Even Japanese carbureted bikes come lean from the factory, and run cooler and better after carb adjustments. It’s an adjustment and not really a mod if u leave the stock jets in, and just raise the needle a hair.

[@Scooter_911]

Thanks for the input!

[@JohnDoe-vq8bg]

Please test as delivered. Best regards!