Garrett AT Max vs Minelab Equinox 800

Garrett AT Max head to head with the Minelab Equinox 800 in a 24 item test garden. See how deep both machines can go!! Iron test included at the end of video.
For fun only!!! Both are great detectors!! Make your own opinions!

[@brianwalker1295]

Sir This was one of the best and accurate test I’ve seen in a while!!!!!!Thank you for posting

[@pedrovision6987]

I almost don't even care how this turns out...the intro was FANTASTIC!!!! OK...back to the vid... A great exercise...very comprehensive...THANK YOU for taking the time to share your test environment!!! WELL DONE.

[@sloboy12003]

I just went from the old school Garrett 200 to the AT Max and you have helped me with using the AT Max. From now on I will be digging all irons also, thanks for your video

[@bravotwozero1020]

Newbie here and those are the two units I'm looking at for my first detector. Very helpful video. Thanks.

[@GenuwineG]

I got the 800…love it

[@stephen3727]

I have minelab Etrac and minelab Nox 800 I think the equinox Got the Etrac beat

[@relicretriever4130]

I have a Max and have heard a lot about the nox so it was good to see someone who knows both machines do a comparison. I learned I need to dig more deep iron targets with my Max. Thanks.

[@highsheriff]

Max is a great machine! I’ve got one and have used it for 1.5 years. Just got the Nox so I am just now learning the ins and outs of it. Thanks for the view and the comment

[@bbushert]

I am having a hard time with my max. Old 1800s sites with tonnes of iron. Get signals everywhere. I dug a couple holes in to craters yesterday. Was getting a decent Signal so i dig then the signal is gone. It was a pretty frustrating day.

[@johnboudreau842]

As a 1 year hunter, Im more confused than ever..Not because of your testing, but because I thought I was getting better at deciding what to dig and what to leave. I probably left some good stuff in the ground and Im going back to those areas and digging everything!!!! I actually got a lesson out of your comparison review.. Thank you!

[@Bayoudigger1977]

I've been digging about 10 years now and there is always something to learn.

[@TECGRAY]

Thanks for the great video on both these units ! Dig everything if your feeling it. Of course I'm still using my Fisher 1266X so I'm use to digging everything for the last 30 years since its a nail and relic magnet. Your video comparison helped me decide to step out of the stone age with my Fisher and go with the 800 for me and the 600 for my wife to get her started in the hobby. Thanks from Ga. :)

[@highsheriff]

Thank you for the kind words. I hope you guys find a truck load of great relics this fall!! Thanks for watching and commenting

[@stonehombre7530]

Outstanding video. To the point 0 BS!

[@longbow6245]

Maybe I missed it, but what were the Equinox settings? What was your Ground Balance, Iron bias, Mode, Recovery Speed? Use these Park2 Multi, auto ground balance every site, leave ground tracking off, recovery speed trash dependent 5-6 for starters, F2=0, and Horseshoe button engaged 100% of the time. I am pretty confident your results would favor the Nox 100% of the time.

[@ColinDeegan]

Great comparison will be going for the 800👍

[@elifallin9708]

The Equinox is also great for picking out small objects👍

[@trevorallan1340]

Good video! Very informative. Would the Garrett do better with an 11" DD coil like the Minelab has instead of an 8.5x11" DD?

[@richardp.6534]

Nice test. Im in the market for an upgrade,,,Currently swinging a Garrett Grand Master Hunter CX3...yes its an old one compared to todays machines, but still performs well and never had any problems with it. Garrett makes tough, solid products that stand the test of time, and for that reason I'm leaning Garrett however when I purchase something I want to purchase the best product that works for my application. So, I'm open minded, and shopping for a machine that will give zero problems in the field and last for a very long time. I'm mostly a coin shooter and beach person...old houses, fresh and salt water swimming areas...That being said I would have liked to have seen how each machine accepts/rejects pull tabs and other small aluminum shards...and along with the nail testing separation, would like to have seen the pull tabs on both sides of the coins...thanks for the video, I appreciate the time it took to set things up..

[@highsheriff]

Garrett is a great company. Thanks for the view

[@charleslawrence2018]

I have an AT Max but the thing I like about the Mine Lab is that the audio alert sounds very similar to a Trumpeter swan.......beautiful!

[@highsheriff]

Thanks for Watching and posting

[@jerrydineen2827]

That was a good comparison between the two machines. I believe both to be good machines, but I'm surly happy with my NOx 800!

[@offthebeepinpath]

I wanna buy one this year. How is it?

[@palerider55]

Good vid, man. I had the AT-Pro in my Amazon buy list for awhile, and almost bought it. But since I see Gary Drayson, the world famous metal detector guy that's also on that show, Curse Of Oak Island, and he uses MIne Lab, I'm glad you did this comparison, because now I have the Nox 800 in my Amazon list and the Pro is gone.

[@highsheriff]

William I’m just glad you took the time to watch

[@stephenhall1497]

Why put the two together ,you no the nox 800 would win .but the settings on the nox would take long time to use just for get it I'm a beginner sod you pair nutters the max is SHIT like u said

[@DirtBandit]

great video. i'm only 14 minutes in but i don't recall seeing you going through the settings on the machines. The equinox is so versatile and has so many settings to can really dial it in for certain conditions. The problem is it takes time and i'm inpatient and just want to hit the soil. equinox 600 is my machine of choice but i'm still a fan of the at pro but it is my loaner or back up detector.

[@highsheriff]

I can’t believe I edited the settings out. Max was in zero mode. Full sensitivity switched from zero discrim to 30 discrim Nox was Parks 2. Full sensitivity, recovery speed of 5, 0 thresh hold, -9

[@DirtBandit]

@@highsheriff awesome, thanks man

[@REDGTA]

If you turn the threshold up on the Nox and leave horseshoe button off, the threshold will "blank" on iron signals. Having the iron bias too high will act just like the AT with too much discrim

[@IffySignals]

Cool Test. Subbed and watching 👍

[@highsheriff]

Thank you very much!!!!

[@bearsden3505]

Good comparison. If you can affotd it, get both!

[@jayhopkins7446]

Enjoyed your video. One advantage of the Equinox is that when you get in iron you can adjust the recovery speed. I do hunt I recovery speed 5 but when I start hearing heavy iron I switch to 6 or 7. You must have some tough soil. In my test garden Park 2 recovery 5 will slam a 12 inch dime. But the VDI is single digits. Park 1 gives a better VDI but audio isn't as good.

[@highsheriff]

Thanks for the comment and view. Yes our soil is very hard and dry during summer months

[@craigshotton3027]

What was you Iron Bias set at with the Nox? It can make a huge difference.

[@creekjonsun]

Been detecting for over 20 years. If it grunts or beeps Dig it !

[@hightwelve9991]

Good video but one question- you made adjustments on the Garrett but didn’t on the 800. Sometimes on my 800 just switching to field mode confirms questionable hits.

[@piedmontartifacts8910]

Hey Travis, i have over 600 hrs with my 800. I would have liked to see iron bias changed and had multiple chances like you did with the max. I use 0 bias and it’s to not cancel non ferrous as bad. Kenny

[@highsheriff]

Man that’s worth a try. I’ll do just that. Thanks for the view and the comments.

[@Unclebub34]

Appreciate the comparison, but would be curious to see the same test after the targets have been in the ground a month or two. Most machines do not do well with just buried targets, which is why a fresh plowed field is not as good as one that has time to settle after the plowing.

[@highsheriff]

Hey, thanks for the view and the comment. You are correct that new test gardens are not the optimal test. It was fun to do though

[@JELLISC]

Great comparison. I don't own the AT Max but I do have the AT Pro. Have you tried the multiple coils that Garrett has to offer like the Sniper coil? I find this coil a lot more useful when hunting nail infested ground. Would love to see this reviewed. I'm probably going to invest in the 800 and re-visit some of my dig sites. Again great informative video.

[@josephtuccillo6438]

With the Max, when its giving you those iron signals on the silver, is it reading the correct depth? If so we can at least say if we get a 10 or 12 inch iron signal, dig it. But if we get a 2 or 4 inch iron we can ignore it.

[@patrickmarino8110]

I like to see them both all out in all metal mode ground balanced and see which detector finds the deepest targets with max sensitivity. I think if you dig all targets in very hunted areas depth is primarily. Patrick

[@mauricenations7511]

My AT Max has has never given a iron grunt on any coin . That machine acts totally different than mine. .

[@P20588]

Same here. My max runs nothing like this Almost sound like it's not ground balanced at all.

[@crazyoldman1968]

i liked and subscribe, your selling point of us learning something sold me, Im writing thos at .40 into the video

[@nowellsmith4511]

You should have shown the settings you where using on both machines

[@user-nj9js2mh7h]

It would be nice to have known what setting you had with both detectors. Example : why are you using iron audio on when sampling silver and copper?

[@CysDetecting]

Good efforts on testing the two detectors , just wondering did you have the iron audio turned on or off on the Max, and what setting was your sensitivity set at

[@highsheriff]

Off

[@highsheriff]

Full sensitivity. That’s why it was so chattery and it probably hurt it some in iron as well

[@CysDetecting]

@@highsheriff id like to see that test with the 5x8 coil on the max be interesting.

[@bobbyhoward6694]

I'm pretty sure you know that AT-Max has got to be ground balance every time you use it on different soil or just about every time you break it out to use it and try it against 800 equinox it'll find stuff that equinox can't even think about finding

[@davidback397]

Id like to know what the targets are reading on each machine if you do this again.......

[@Russ92]

I live in NorCal, which detector on your opinion would be better for nugget hunting?

[@mike94560]

Whats great about this video is how deep targets don't read like what they really are. I might start digging more now.

[@highsheriff]

That’s true man. Even with both machines deep targets have lower VDI numbers

[@werjr4417]

As an AT Max user, I never search with the iron grunt button active. I only use that when I want to check a signal.

[@highsheriff]

I never used it either.

[@NickBell81]

Yah need to turn off iron audio

[@davidwhoever5043]

I agree you should never leave the iron grunt on.. I would like to see him redo the test with out the iron grunt on.

[@diggingnashvegas]

Or in all metal mode

[@kevinholmes2013]

He isn't using his ATMAX correctly to perform this test. Getting onlu grunts on Silver at 10 inches ? Your doing something wrong my friend.

[@bobalmendinger4930]

Can you tell us your settings on each detector , sensitivity, mode, recovery speed, multi frequency, etc

[@highsheriff]

Sure. The Nox was Parks 2 recovery speed of 5 full sensitivity Atmax. Zero mode. Full sensitivity

[@DirtyMoneymetaldetecting]

I think having the nails on the surface isn't a realistic test. Isn't a detector going to focus on closest item to the surface? I would have liked to have seen the iron at different depths in relation to coin.

[@jeanponce2017]

You didn't ground balance after you turned the Maxx off? I don't believe it saves the ground balance setting after she is turned off. I GB mine each time it's turned off. You have to or it's handicapped

[@horseman528]

What I don't like about the Garretts is they will give you two simultaneous signals at once. Even when you turn off the iron grunt, you will still many times get two simultaneous signals. They're too chattery. I always liked the Tesoros because you would get one signal clear and crisp.

[@ThelifeandtimesofBarneyTaylor]

I learned something thanks I will be digging 5 if it’s deep

[@jaystrongbow9435]

Something seemed off on your Nox here. Pop your coil cover, clean the coil, do a factory reset. Run 0 FE and F2, recovery 4 or 5 is fine. I have had an 800 for 2 years and it crushed my Garretts in the iron. It was like I never dug my areas before. You might consider sending the Nox in and getting it recalibrated if a coil clean and factory reset don't bring it up to par. Send in the coil too, as the coil could be defective . If that was my Equinox, it would go back same day.

[@highsheriff]

i don’t know what issue you saw. works just fine. cool is brand new. There is a lot of interference at that site due to large power lines and radio towers

[@andrewwilson8317]

Damn, watching this and thinking going to have to go back over some fields. I have rejected signals on iron grunt and now thinking I may have missed stuff!

[@williamburmeister2523]

Maybe I didn't catch it, but what mode were you running the Max in and what sensitivity? I run mine in Zero mode, sensitivity two from top, zero disc. To me it just didn't sound right? I've ran both machines so this was entertaining, however just seemed like each machine wasn't ran at their peak performance.

[@highsheriff]

Parks 2. Recovery speed 5 nothing discriminated full sensitivity Zero mode on the Max. Full sensitivity and it had a brand new coil on it. I switched back and forth with 30 discrimination to 0 discrim.

[@williamburmeister2523]

@@highsheriff oh ok, the full sensitivity is probably giving you all that unececary feed back. Also did you factory reset after putting on the new coil? If not that is also giving you the in my opinion weird results I was seeing.

[@highsheriff]

Michigan History Hunter yeah probably. I went with full sensitivity because I didn’t want people to be able to say that is why either instrument didn’t go as deep as it should. The full sensitivity also makes it worse in iron in my opinion anyway. Thanks for the view and the comments

[@ohiofarmhunter3301]

Here's the simple truth no one stands in a spot swinging over the same patch of ground so if it doesn't hit the target the first swing it even the second swing and let you know it's there you are moving on....

[@DroneLifeLelystad]

As a garrett fan, the Nox 800 just did a little better, great comparison. Dunno if i will buy the Nox just yet, or save a little more for the XP Deus. I love Garrett's started with the Ace 250 then the EuroAce then the ATPro and now the AT Max. But really considering stepping over to something new.

[@highsheriff]

Thanks for watching and posting. Both are very good machines. Nox gets the advantage in the iron

[@MrBrad9]

Been a Garrett user forever. Seriously looking at the nox 800 for a second machine.

[@tbled52]

Opinion question. Is it worth have a second machine thats a different brand to utilize it in different situations or is it better to stick with one brand for familiarity?

[@MrBrad9]

@@tbled52 Depends on your situation. I have a Garrett AT Gold. I can't run it in Salt water hence my desire for a Nox as a second machine. I know there is the Garrett Apex which seems to be good for salt water however it's not waterproof. That's a big NO for me. If I'm going to be around water I want my machine to be waterproof. Common sense IMO. So Nox it is. If I was just running my machine in fields, parks and dry land I would stick with what I know. I may look into an Apex or a Max in that situation.

[@hotpockets3660]

I would've like to have seen a buttons control explanation on each machine. I also feel that the coils have alot to do with it. Both seem to be awesome machines but I must say that I like the tone sounds and the recovery best on that AT max.

[@bbushert]

Do you want to buy an at max

[@hotpockets3660]

@@bbushert I do want the Max. Have wanted one for a long while now. I plan to get one as soon as we get that check lol.

[@highsheriff]

Thanks for watching and commenting

[@philipdethlefs1631]

The coil has a lot to do with it as well... I like seeing side by side with the same coil on each detector, just a thought.

[@midwesttreasureandrelicrec7914]

You can't put the same coil and each detector you can even put a similar coil on each detector one is a multi frequency when as a single frequency is not even close

[@CarolinaDiggers]

Sweet video. I’m actually thinking about getting a new detector.

[@highsheriff]

The Nox is fantastic in Iron

[@CarolinaDiggers]

I don’t need a 800. I will never use it for prospecting

[@CarolinaDiggers]

The 600. If I decide to go that way. Will most likely be the one I will choose. I am actually leaning towards the Simplex +

[@andrewrobinson2869]

I dont suppose you have any Australian coins. I currently have a AT pro but after 6 years i need to reset every time i turn as it on. So i am trying to save t o upgrade. However i dont know if i should go with the AT MAX aas i am use to the AT PRO OR go the Nox 800. Any advice or if any of of you followers are in Australia and could help me. Since i am on a disability pension. ITS going to take a few months to save that type off money. But i can't afford to waste and buy t lhe wrong machine for Australian conditions and coins. Thanks for any help or advice. Regards Andy

[@dougosgood3437]

My concern is the iron bias and the recovery rate on the Equinox. If the recover rate was set at 2 and the iron bias was set lower like 3-4 then the Equinox will detect deeper. You were messing with settings on the Garrett. But not on the Equinox. Doing the above the Equinox will separate better also. Doug

[@highsheriff]

I got ya. I hunt very heavy iron relic areas so my recovery rate will never be a 2. You are right I could have made the NOX deeper

[@fredyzzz007ify]

I had a equinox 800 that I just return, in my eyes it’s to complicated to use had to dig lots of nails and pull tabs, am buying a at max since does have the tab setting and some also have aluminum. I had a bounty hunter that I like more then the equinox 800. That’s just for what I do

[@schaedutton4928]

I never turn my iron off on the nox I just turn down the volume on it and when I hit heavy iron I turn the recovery speed up .

[@highsheriff]

Same here

[@DenaMichele]

Great video! Thanks!

[@highsheriff]

Thanks for the view and comment

[@JasonWh]

A good reason to have more than one unit for conditions. I have the AT MAX, E800 and the Gold Monster 1000. It's amazing the differences I find solely based on soil conditions regardless of how I try to filter around them.

[@stephenhall1497]

At max is a beast with the right coil

[@rickybean6236]

Travis good video,you should leave them in the ground and do the same test in a month or so.

[@highsheriff]

I will.

[@highsheriff]

I realized that 12 inches was too shallow. Both machines on different targets could have went deeper

[@Kliph4ShariLove]

Well, maybe not the wifie's ring LMBO JEZ SAYN'

[@mayleecole1761]

My father is considering getting into metal detecting we are going to buy him one for Christmas this year 2021 after watching too many videos on which machine to buy I have decided to get the at pro Garrett. A beginner detected change my mind the at pro seems to be the more friendly beginner machine less things to worry about set in the coin mode and go then he can learn off that. That's the problem with videos like yours you assume people have knowledge of metal detectors most do not I looked at all metal detectors and it seems to me the Garrett at pro is the way to go I'm looking for a machine where you can learn what he's looking for the at pro seems to have the best advanced features with novice wisdom

[@OPInformer]

Good video. What detector would you recommend for just coin hunting?

[@highsheriff]

There are numerous good detectors out there. For decent prices. Minelab And Garret are great to chose from

[@OPInformer]

@@highsheriff Thanks I'm having a hard time trying to decide between the at max or the equinox 800. Which would you recommend for coin hunting?

[@TheRockDetectorist]

im deciding between the max and nox but im leaning towards the nox because it does the beach really well and gold prospecting. From what ive heard and seen the max is ok on beach but basically can't gold prospect at all. Am I doing the right thing by getting the nox because im going to be going to old gold mines and the beach. Thoughts?

[@highsheriff]

You will not regret the Nox! Hands down better machine

[@highsheriff]

Thanks for watching and commenting!

[@lonnieculp]

Today I fetched my Whites 4900D Pro Plus from the garage, cleaned 10 years of dust, and put fresh Duracell C's in it like always... and it didn't work for first time in 35+ years. Welp, it's time for a replacement so I dove in to researching the latest and greatest thinking all this new high tech stuff was gonna be light years ahead of my first 'tecter.... after watching this video (and the last 8 hours of scouring the web) I learned something that surprised me. That old 4900 is gonna be hard to beat (except for the lack of underwater capability). If anyone knows where I can get my Forty Niner rebuilt please let me know.

[@rudyceballos8471]

RR, can you tell us, what were your settings on the 800.

[@highsheriff]

Parks 2. Full sensitivity, 5 on the recovery speed, 0 thresh, -9 accept reject Custom tones

[@plugsfordays648]

Recovery goes to 1 that’s the lowest right ?

[@FindingAlabama]

Just found your channel..enjoyed the tests.. I swing Nox 800..couldnt keep my sanity swinging that max..the iron volume is horrible!..h.h.

[@highsheriff]

I have found a ton of good things with my Max but you are right the Tones on the Nox are amazing!!

[@ronalddvorak1967]

On the Equinox, You didn't even mention recovery time. It's great in iron if you set the machine up right.

[@highsheriff]

I think in the front I stated the recovery speed was set at 5. It was so much to cover in one video. I am afraid it is too long for most to enjoy. Thanks for the comment What speed do you find gives good depth and recovery at the same time. Thanks again for watching and commenting

[@ronalddvorak1967]

@@highsheriff I use the fastest recovery setting in real iron infested areas. You lose some depth doing it.

[@ronalddvorak1967]

@@highsheriff Your video was Very good, I did enjoy watching it. But you are more knowledgeable by far on the Garrett than the Equinox. The Garrett is a great detector, each has its place.

[@highsheriff]

Ronald Dvorak you are 100% correct. Only about 80 hours on the Nox but I’m enjoying it

[@HighTones]

@@highsheriff Nox is awesome! I purchased my 800 and 600 back in June and i have already found over 25 rings 4 gold, several silver and a few plated. One class ring 14kt and one with 10 diamonds 14 kt and one 14kt white gold that hit 10/11 on vdi. If you dig the 9 and up to 13 numbers you will dig a gold ring eventually. Nox also produced a 1794 Spanish 2 Reale. What fun!!

[@bigshow6200]

What was your sensitivity set on the Nox, be honest👍

[@highsheriff]

Full blast on both machines

[@MrWatcher46]

Ground looks very dry, and the coins were just planted. This will make a HUGE difference in detection depth. Coins that have settled in the ground for years, decades, or a century will create a halo effect that will allow you do get a solid hit with a much deeper coin. I have dug half cents and dimes at 10+ inches with a tone that would blow your earphones off! I'm running a Whites DFX for reference but am looking to acquire an AT MAX. Happy hunting!

[@highsheriff]

All true. Thanks for the comment and the view!!!

[@mikeknobldiggin]

Man you just tackled a big subject with a wide brush. There are so many variables in this. You did a great job overall but there are so many ways to tweak each machine. Especially that Equinox. So now you have a test Garden, I recommend you do certain tests. For example, test the Equinox in all-metal mode with fastest recovery speed against the AT Max in all metal mode. And then try each with iron discrimination on. Also you may want to swing the Equinox over your deepest coin and back down the recovery speed in increments to see what it does to the target. I think this could become several videos between these two detectors. Great job so far.

[@highsheriff]

I sure did. LOL. Especially with the Nox. There are so many options with that thing.

[@diggingnashvegas]

Dont think you put the max in all metal mode, justcheck numbers, goes a lot deeper

[@tomellsworth2726]

He also had the sensitivity all the way down on the max . you can see it when he is doing the wedding band (18.37)and cant help but wonder if it was down the whole time.

[@davidwillis3218]

@@tomellsworth2726 I’m a little late to the party , WOW . ( YOUR RIGHT !!! Damm )

[@davidwillis3218]

He’s right. 16.49 also , what a shame ..

[@elifallin9708]

My favorite mode for the Equinox is parks 1 at 10kz what's your favorite mode

[@highsheriff]

I use Parks 2 with modified sounds and tone breaks set to my likings. I have my iron volume on a 2 and everything else set At 25 I use 6 recovery speed and -9 on the discrim Sensitivity at about a 23

[@highsheriff]

Eli Fallin I wonder if that defeats the purpose of a multi frequency machine? You will be good at finding high conductors but you will miss a lot of low conductor relics like buttons and such

[@kenvansanford6323]

Hey what are your settings on the nox 800. And what is your recovery speed on the 800?

[@highsheriff]

Parks 2, my custom tones ,full sensitivity, 5 tones, ground balanced and noise canceled, 0 threshold, -9 then 5 recovery speed

[@CarolinaDiggers]

Can you do Two Tones on the NOX?

[@antoniohobbypuglia]

Winner is?

[@jjuanmarin]

why does he moves the detectors so fast

[@g.fortin3228]

if you are doing silver might want the eq in 5k and hear them light up.. also you didnt mention at the beginning what recovery speed you were using. Just saying there are settings there to play with, and you played with discrim on the garret.

[@highsheriff]

Thanks for the comment. I played with the Garrett Because I had to. LOL. The Nox didn’t need it. Hands down a superior machine

[@gregsanderson2470]

RR its a year later. Do you still have that opinion? Thanks G

[@Bayoudigger1977]

At Max all day. So much easier to use and versatile in thick, wooded areas.

[@SGTsDiscoveries]

"DIG IT ALL, SAVE SOME HISTORY!"

[@fazilkhan2685]

What’s the difference between these 2 and witch one is the best

[@highsheriff]

I would say all around the Nox is a better machine. However the Max is probably a better water machine because the Nox has leakage issues Both machines are very good. The Nox is better in heavy iron and the Max is better or at least more dependable in the water

[@swampfizz]

practice makes you better folks..if you're in good health dig more iffy signals with any machne you'll be surprised by what comes out

[@tomr2210]

How do they compare on the beach. ? Thx

[@rivercitymetaldetecting9854]

Multifrequency machines such as the Minelab will outperform single frequency machines such as the Garrett. You typically have to dial the sensitivity back on the single frequency machines to get them stable in wet saltwater sand.

[@Tykhyy]

Hello, I am your subscriber and I need your advice, I now have a Nokta impakt, and I want to buy a second metal detector, what would you advise between these two Minelab EQUINOX 600/800 or a new ACE APEX, please tell me. Thank you

[@highsheriff]

I love my Nox 800. The Apex is probably a good machine but not water proof. If you have $900 go with the Minelab. For the money the Apex is probably a good detector. Simplex is also a good reasonably priced machine. The Nox 800 is hard to beat

[@Tykhyy]

Rowan Relics Thanks

[@robbiestephens49]

U should try the anfibio i nail 10 inch coins all the time

[@maxi3437]

Who has won???/Please write here..don't understand english...sorry translate with translator (((

[@davidwhoever5043]

You where using the Max total wrong.. for all you new guys that just got to your max. Do not leave the iron grunt on.. only us that function when your double checking a target... by leaving the grunt on you will miss targets point blank but if it's off you hit them.. the guy that did the video did a good attempt at comparing the too but doesn't fully know how to use the max.

[@james30k]

I totally agree I have the max and this guy is using the max wrong .. I bought the 11x12 superfly coil on my max and I bought the lithium rechargeable batteries for my max and this metal detector is a beast and it’s behaving way more better with the nel superfly coil on top of that the max is much more lighter with this new coil .. But ya I agree what your saying.. anyone with the at max should upgrade there coil with the newest nel superfly 11x12 coil it’s a perfect coil for this metal detector ..

[@thomasnappo6309]

Garrett hasn't upgraded really any of there M.D...MINELAB HAS BEEN IN THE LEAD...FOR MANY YEARS NOW

[@midwesttreasureandrelicrec7914]

I say this with love owning both machines plus the 80 pro there is no way that equinox hits a tenant's nickel and not a tenant's quarter I would like to see what settings you're using with the equinox judging by the Klux I hear I would say your iron bias is not set to where it needs to be also where is your discrimination and Recovery speed These 3 things greatly affect Deph. Testing these both side-by-side just like you did and in the field I can tell you that the equinox picks up things at depths that the AT Max doesn't even think about.

[@bobalmendinger4930]

What was the recovery speed set at on the 800 ?

[@highsheriff]

5

[@bigshow6200]

Should had dropped it to 3, all coins would had been detected with good signals

[@bobalmendinger4930]

@@bigshow6200 it does gain a lot of depth going slower on the recovery , just starts to get the signals a little mushy if it's trashy.

[@ArbitraryLifestyle]

When you have discrimination turned up to 30, can't you just press the iron audio button to here 0 - 30 without having to turn the iron discrimination all the way down and then back up to 30 again?

[@johnnykoba_on_the_road]

So basically, on an at pro just turning discrimination off

[@roadperry8806]

I’m Studying ALL Brands Never Done B4 but Want to Learn 45+ Hope to Search Til Right one & reviews show best

[@changovanilla]

The sound on the at max is enough to drive a person crazy!!! I much prefer the sound from minelab detectors.

[@Po1itica11yNcorrect]

The audio alerts alone are enough to make me pick the Nox over the AT Max. That horrific Max tone is grating on the ears. It would cause me to cut my detecting adventures short just to give my ears a break. Disclaimer: I don't own either one.

[@cryptocrunchies2478]

Your volume is too quiet to understand what you’re saying with my iPhone. Yours isn’t the only channel but most of my favorites definitely have more volume available

[@highsheriff]

Sorry about that. Thanks for Watching though

[@AtukNakal]

Use iphone 11 pro and you can hear him clearly 😅

[@nerijusrimkus8883]

Sveiki As turiu at max ir esu patenkintas. Net su senuoju Garrett Euro Ace esu daug ko rades ir gerai dirba, tai su at max nera ko lyginti euro eiso.

[@markdoehrman5855]

Odds are the garrett will id better most times?,where the Nox likes everything deep,,more of a dig it all machine. I have vanquish 540 friend has nox 600,,90% of our targets fall in 18-20 range and high tone even if its trash,,but yes it is deeper than the max,,but you will dig a ton more. Just my opinion so far.

[@highsheriff]

Thanks for watching and for the comment!!

[@harryswitzer5722]

very good video, however its pretty obvious you are a garret fanboy. you never adjusted the minelab 1 time. just my thoughts!

[@midwesttreasureandrelicrec7914]

I'm sorry but the circuitry and the audio on the garret his prehistoric

[@ericcampbell8881]

Not fair the ML has a round coil and the Garrett has a DoubleD

[@rivercitymetaldetecting9854]

They are both dd coils. One is round(ML,) and the other(Garrett) is elliptical.

[@user-yy4up8qf5m]

"I don't think I want an overpriced over hyped Garrett metal detector that grunts on silver!" Otherwise I'm all in on the AT Max! This video unintentionally exposes Garrett and sets their hokey metal detectors back into the toy class analog stone age. Right now the quest for silver coins has never been greater and I do not want a metal detector telling me a 90% silver coin is iron! Please tell me... Is the AT Gold gona grunt on gold! Garrett if your metal detector can't tell the difference between silver and Iron... how's it gona tell the difference between iron and gold!