4T40E Teardown

[@BobBrandenburg-f9y]

Wow thanks gary my 06 malibu had the same exact issue. No Forward motion. I pulled the tranny and was deciding what to do and I tan across your video. You lead me right to the tubes and sure enough it was broken just as the one you were repairing. I am going to replace the tubes and get it back together. Thanks so much.

[@psicopatalucifer]

Mystery solved, a broken tube excellent case .! Thanks for the video Gary.!

[@finalcallracing]

Had bunch of these come in. Customers always think its going to need a trans or major overhaul. Drop pan and swap the tubes out in like 30-45 mins and customer back on road happy as a lark.

[@GaryFerraro]

Yes, very common problem

[@donaldwhiteman3224]

Love the video, I'm doing my transmission the end of the month!

[@GaryFerraro]

Ok, any questions just let me know

[@donaldwhiteman3224]

Ok kinda late but could i put the 5th gear in this transmission or dues it have to be a different 1

[@kenyoung5682]

You are so right about the code 1810. When I foolishly swapped a 2003 Cavailer engine/transmission into a 2004, everthing was fine. However, when I then installed the 2004 engine/transmission into the 2003, I could not get rid of the 1810. Thank you for your video.

[@GaryFerraro]

Thanks for watching.

[@grahamh6444]

Great video again thanks for sharing

[@GaryFerraro]

Thanks Graham

[@JoeyLovesTrains]

This is the exact same setup in my 2007 Pontiac G6

[@TerminusOmega13]

Would this tear down also apply to a 4T45-E and how necessary are the specialty tools for disassembly and rebuilding?

[@christianmaheu9565]

I first suspected those tubes. It happened to me no forward but reverse ok. When it happened to me I though it was a solenoid but after watching a few youtube videos realized it was the tubes. I couldn't do the job myself because it is winter and I don't have a garage, so ,I brought it (had it towed) to a shop who wanted to change the tranny .I said no brought it to another one same thing. Had to change the tranny , but it has been summer time , I would have change those tubes myself.

[@gelatizzimo]

Another great lesson.Thanks Gary

[@GaryFerraro]

Thank you

[@RobertHeller-f4o]

How many quarts of fluid dose it take to refill

[@cw824]

Note to self, remove pan and check tubes before full trans Teardown!

[@GaryFerraro]

Funny thing is, one time I did repair the tubes and 2 weeks later came back with an input speed sensor code so it ended up needing overhaul anyway. Go figure. Thanks for watching

[@cw824]

@@GaryFerraro Just pulling your chain Gary. Excellent and very informative video. Thumb up, I learned alot!!!!!!

[@GaryFerraro]

@@cw824 LOL, thanks again, glad you enjoyed

[@sparkplug1018]

Very insightful video, lost reverse all of a sudden after the car was towed. was thinking id have to rebuild it but those tubes being broken can cause that too? The car had a blowout in the rear so naturally they sent a spatula truck and towed it all the way home hooked from the rear! Could that have damaged internal components and caused reverse to fail? Shifts through all 4 forward gears fine, and the TCC engages like it should.

[@GaryFerraro]

Do you knopw if the car was running when it was towed? I would check those feed pipes, there is a reverse clutch feed pipe

[@sparkplug1018]

@@GaryFerraro unfortunately it wasn’t.

[@adrianrodriguez8479]

Así como subes tu vídeo de desarmé, deberías subir el de armado, para que entendamos bien cuál es el problema real. Gracias

[@GaryFerraro]

translation

[@johng5261]

I have a 4T45-e and its delaying shift and making a thud while shifting into 2nd, do you think its lack of pressure due to a crack possibly in the tubes? Hate to go through the whole thing just to be a tube.

[@GaryFerraro]

well if this takes off from a stop ok, may not be the problem. Do you have any codes present for the trans?

[@johng5261]

@@GaryFerraro just realized the traction control light comes on and then it shifts way worse. on these saturn aura / malibu it seems to be a somewhat common connection. It takes off ok, drives fine more or less until that traction control light comes on. I dont have a solus or a tech 2 to read the trans codes unless there is a way to get them with a standard obd2, I know some cars will pass them along into the main ECU. What do you think I should check?

[@GaryFerraro]

John G This car does not have it’s own TCM so you may get the codes out

[@johng5261]

@@GaryFerraro I dont see any being thrown. So it would just show up like a normal ECU code right?

[@GaryFerraro]

@@johng5261 Is the check engine light on as well? how long can you drive this before it starts acting up?

[@R.E.HILL_]

Nice. But 360p does not do you justice. Thx for sharing.

[@GaryFerraro]

Thanks for watching, please subscribe

[@gav3379]

Hi Gary, I have a question. I removed the stub shafts in my 4T45-E transmission to replace the seals and cups. The RH side shaft came out with no problems using a slide hammer tool I made that grabs the groove for the spring clip. The LH side however was more difficult. It finally came out but the inner spring clip was broken in half. I could not find the other half of the clip. I tried using a magnet as well as a vacuum but could not find it. Do you think this piece of the clip will cause a problem in the transmission or will it eventually fall into the pan? I did drop the pan but it was not in there. I have not started the engine as I am going to replace the filter and oil. Thanks. Update: Transmission started making grinding noise this week 3/6/21. Took it apart and found differential planetary gears stripped. This is where the C clip broke off from the LH drive shaft when I pulled it out. Not good!!

[@tumashedrick]

New subscriber im looking at a 2009 chevy Malibu as my next daily they say the transmission is bad so im wondering if its the tube like in this video

[@GaryFerraro]

Are you sure it's tis transmission and not a 6 speed transmission? What is the problem

[@tumashedrick]

@@GaryFerraro it says this trans on Rockauto under the transmission rebuild kit

[@GaryFerraro]

where are you located?@@tumashedrick

[@tumashedrick]

@@GaryFerraro Oklahoma City Oklahoma

[@jls16845]

Maybe you can help me out....I have a 4T45E Trans in a 2006 Cobalt..... on the TCC Lockup Solenoid that goes in the Valve Body When I took mine off the inside went flying..now I'm not sure if that little spring goes in the middle then that little shaft..or the little spring goes in the Valve body 1st then the shaft, then the sensor...Any help would really be appreciated..Is it Solenoid... then Spring.... then little shaft.. .or is it Solenoid.... then Shaft...then spring....Thanks for any help Jim

[@GaryFerraro]

sure, Spring first, then valve, then solenoid

[@budh420]

my 97 malibu 3.1 v6 has this transmission and I have a tech 2 tool showing a TCC enable sol fault and not showing any codes not enabling in 4th gear??? Do you know what could cause this?

[@GaryFerraro]

Can you tell me the code number?

[@budh420]

Apparently you have to be under the correct body selection in the tech 2 tool, I was under W which is the 4t60E and mine is the N body 4t40 E and everything is fine under that, thanks for the reply, any way you can make a video assembling one of these?

[@GaryFerraro]

I will keep that in mind, thanks for watching

[@Bigmikepolzien]

2007 Chevy HHR. Transmission isn't catching gear when I get off the freeway (at a green light) and accelerate after making the turn. Now it's not catching gear when taking off from a red light. Do you think it's the tubes? It's super frustrating because it's already been rebuilt twice within 3,000 miles, and last time the rebuilder said they replaced all the internal parts.

[@GaryFerraro]

When you say not catching, does it not move forward?. This is a 4T40E, no dipstick, your sure it's full?

[@Bigmikepolzien]

@@GaryFerraro Yes, it doesn't move forward, the engine just revs. It eventually catches in first gear (I think, it might be second.) The fluid level was checked on Thursday and supposedly it's fine.

[@GaryFerraro]

@@Bigmikepolzien If it moves forward may not be the tubes, usually when they break it will not move at all. reverse is ok? wondering if this is in limp mode, when it is it will take off heavy from a stop

[@Bigmikepolzien]

@@GaryFerraro Yeah, reverse is fine. It was driving fine on the freeway, then out of nowhere, the rpms started jumping around, I slowed down and it went back to normal, then when I excited the freeway, that's when I had problems with it "neutralizing." (That's the term the shop that rebuilt it used, but they cant seem to figure out the cause of it.)

[@GaryFerraro]

@@Bigmikepolzien It neutralizes on take off or on a shift?

[@carolwoodruff4767]

I have a 06 pontiac g6, that had been bang shifting for a year, only sometimes though. So that led to people trying to diagnose an issue just based on my description, as when they would drive it it would shift smoothly. Then yesterday parked it at work just to run in quickly, left it running, tried to leave, but no reverse, never felt even try. I still drove it for the next few hours running errands. Its parked at home now and while in reverse there is now ticking, nuetral too I believe but not in any forward gears. Please help or point us some where. I would love to exchange emails or let my husband pick your brain by phone. We are desperate and broke

[@GaryFerraro]

carol woodruff can you give me the vin number of the car please. Just want to confirm transmission type

[@GaryFerraro]

carol woodruff my e mail is [e-mail].

[@nickolas6664]

carol woodruff same thing happened to me. 2008 Chevy Malibu 4t40e, which has same transmission. Finally pulled it out yesterday and disassembled. Found out the sun gears were destroyed. Hope it helps.

[@AntonioLopez-hk4cs]

Solutions 😒😒😒😒

[@ianhylton1974]

Hey Guy how you doing I have a 1999 Chevy Malibu 3.1L V6 with a 4t-40-E that was rebuilt once back in 2010 should I do a fluid change or a flush? I have no shifter issue everything seems fine also what additive should I use along with fluid? I'm going to be using full synthetic fluid by the way recommended by the dealer Dexron 6

[@GaryFerraro]

Ok, change out the filter as well, new pan gasket and fluid, no additive

[@waynep343]

Gary. how do you get the press in transmission oil cooler seals out. that is something i have not done. 4T45E wayne over at automotive.com forums.

[@GaryFerraro]

You have to knock them out, i use a screw driver to get them out and a small bushing driver with handle to knock them in, if they look ok, you could also just leave them in. Hope all is well wayne, shop is pretty packed

[@waynep343]

forums.automotive.com/70/9761497/general-auto-repair/tranny-line-seal-stuck-i-motor-on2001-olds-alero/#9761509 thanks gary..

[@jessicawest9296]

Hi there I checked all the wires nothing broke or bent now what

[@modeverything1]

Can you just remove the valve body assembly with out pulling the pump off? Just looking to swap out the chain set gears without doing a full rebuild! 😄

[@GaryFerraro]

Mod Everything Is the chain jumping? Never really seen that yet

[@modeverything1]

@@GaryFerraro no I want to change the gears to change my final drive ratio from a 3.05 to a 3.63 by changing from 35/35 tooth sprockets to 32/38 tooth sprockets. Just trying to do it simple as possible! Lol

[@GaryFerraro]

@@modeverything1 What are you going to do with the ECM, if it sees wrong ratio will store codes

[@modeverything1]

@@GaryFerraro I have HPTuners, you can adjust the gear ratio calibration and flash it to the vehicle.

[@АлексейН-б2э]

good day unfortunately I do not speak your language sufficiently for communication .. because I am writing through a Google translator Let me ask you a few questions. I have saturn wue. AQPP 4t45, while the gas is being added, the car does not accelerate fast enough .. can you tell me what it is preparing for? and the second question ... what's the difference between 4t45e and 4t40? with respect Alexey

[@GaryFerraro]

Can you scan for codes please. Just difference in torque rating, the transmissions are pretty much the same

[@arietap9657]

Did this failure cause any codes in TCM or ECM?

[@arietap9657]

Great video by the way thanks so much for posting it.

[@GaryFerraro]

@@arietap9657 I don't believe it did

[@arietap9657]

Ok thank you

[@maadenengineering9101]

great video Mr.Gary. plz I need 722.3 transmission teardown and reassemble videos . I search but I didn't find it. can u plz send me the link for treason and rebuild videos. thanks

[@GaryFerraro]

There is a company in miami that has a CD that is downloadable to a PDF file on this unit, its says it covers diassembly and reassembly. The company is ATSG(Automatic Transmission Service Group) You could probably purchase online and download it.

[@maadenengineering9101]

Gary Ferraro thanks for ur support.

[@maithamdehedhawi7890]

Very very thank you.

[@GaryFerraro]

Your very welcome

[@maithamdehedhawi7890]

كيف يمكن معرفة رمز ناقل الحركة مثل 4t60e واين نجده مكتوب

[@paulaoliveiracantorajoioeo2493]

Tudo bem com vcs tenho uma transmissao igual a essa no meu carro o que aconteceu estava andando com o carro a mais o menos 60 km por hora quando a pessoa que estava do meu lado desligou a chave com o carro andando e engatado vez um barulho de estriado rosando depois ela não abda nem pra tras nem pra frente oque pode ter quebrado dentro do cambio ou o sistema broqueou

[@maithamdehedhawi7890]

How can i know the transmission code such as 4t60e or others and where we can find it writtin.

[@GaryFerraro]

When you say code, do you mean transmission type?

[@maithamdehedhawi7890]

Yes. Wheni say code i mean transmission type.

[@GaryFerraro]

Most transmissions may not have a tag, there is an app you can down load for free by a company called Transtec, they have a chart to I.D transmission type, or call the dealer with the vin number.

[@silvianoayuzo554]

Por favor la ayuda de gomo medir el nivel de aceite de esta caja

[@curioushat]

Gary, great video - thanks! I have ''09 Malibu with 2.4L/4T45E with over 195,000 mi. The transmission is "missing" 2nd gear in "D", it goes 1-3-4: to high RPMs in 1st and then in 3rd (in "I" it goes from 1st to 2nd as expected). To rule out TCM issues, I did a test drive with OBD2 scanner connected: the TCM commands 2nd gear but the gear ratio stays as in 1st until TCM commands 3rd gear then the ratio jumps to 1:1 (3rd). Overall, it looks like a common issues with missing 2nd gear in 4L60E (atracom.blob.core.windows.net/manuals/individual/2013/2013-038.pdf). So I suspected that pressure was off and too much signal oil was entering 1-2 solenoid and was holding 1-2 shift valve until 2-3 opens and oil is routed to the spring end of 1-2 valve. Without removing the transmission from the car, I replaced Pressure Control Solenoid, and both 1-2 and 2-3 solenoids, but it made no difference: still missing 2nd gear in "D". The 2nd gear still work fine when driving in "I". I don't understand how the oil flow changes when driving in "I" vs "D", so I have hard time identifying the root cause. Do you have any idea what can be wrong or what other tests can be done? As a side note, when changing solenoids, I changed oil and filter: oil was fine and there was little accumulation on the pan magnet. Also there is no any fault code.

[@GaryFerraro]

In 2nd, the 2nd clutch is applied and the 2nd sprag is holding. This is not common, haven't really seen this problem, could be a stuck shift valve, or bad sprag.

[@curioushat]

@@GaryFerraro Gary, I was thinking about stuck valve too, but I don't understand why would a valve be stuck when driving in "D" and would work properly when driving in "I"? Or is transmission works so differently in "I", that stuck valve would not matter? I have similar question about your the bad sprag idea. Any thoughts?

[@curioushat]

@@GaryFerraro Gary, can it be failing pump? If so, how would you test/check the pump on 4t45e?

[@GaryFerraro]

@@curioushat If a bad pump overall pressure would be low, would delay in drive slip in reverse just to name a few, if reverse is ok pump is fine

[@diegozoreque5129]

I'm having a hard time putting the torque converter back in place

[@GaryFerraro]

You mean installing it onto the trans?

[@diegozoreque5129]

Yeah but I got it now

[@GaryFerraro]

@@diegozoreque5129 Ok, thanks for the update

[@brayancabrera9892]

hey my friend I need to know if the torque converter can be repaired on this transmission or do I have to change the entire transmission ???

[@GaryFerraro]

Sure, you can just replace the converter, have to pull out the trans

[@iblacka1]

I want to see the length of the accumulator Springs put them aside Jesus Christ

[@GaryFerraro]

Hey Ivan, i guess i did not show the springs, sorry. Will keep that in mind for the next teardown, recently did a teardown on one of these, maybe i show the springs in that video

[@marksimmons3801]

video too dark ! turn sum lights on !

[@GaryFerraro]

Ok, will do, thanks for watching

[@marksimmons3801]

thank you sir !

[@marksimmons3801]

@@GaryFerraro i took a valve body cover off mine and as i stated to separate it from the case i noticed a bullet shaped object fall out it got groves in the side and ashot needle at the end of it !!!! any idea what it might be ?

[@GaryFerraro]

@@marksimmons3801 My e-mail is [e-mail] Can you send me a picture

[@gilbertoguerrero8818]

Escuchar en español

[@jessicawest9296]

I have a 99olds Alero code1810

[@GaryFerraro]

That is a pressure switch code. Do you have access to a scanner the shows live data for transmission?

[@jessicawest9296]

@@GaryFerraro no just a regular obd

[@GaryFerraro]

@@jessicawest9296 ok, if you clear the code, how fast before it comes back?

[@jessicawest9296]

@@GaryFerraro soon as I turn the car off then hook it up to the computer again

[@GaryFerraro]

@@jessicawest9296 so basically it comes right back or won't even clear, was anything work done to the car and then this happened?

[@gilbertoguerrero8818]

Escuhar en español

[@GaryFerraro]

Not sure how to do that