Sorry, took forever to load. Tearing down a 722.9 4Matic Transmission that was slipping. We start with the Transfer case so everyone can see how it comes apart and then teardown Transmission. Enjoy, Thanks for watching
Пікірлер: 81
@oldschool9746 Жыл бұрын
Thank you Gary, hope you have a great week!
@SrColon30911 ай бұрын
Thanks for sharing your knowledge and experience.
@TheKarabala Жыл бұрын
Nice to see you Gary. Take care
@jimmyroos1677 Жыл бұрын
Gary, the B1 clutch basket really sits !!! I use a solid plastic hammer and HAMMER it from the bell -housing side, no marks or dents ...
@igotaction Жыл бұрын
Keep the ZFs and 722s coming Gary!!!!
@GaryFerraro Жыл бұрын
Thanks Joel Will do
@user-pq4yh2fu6f9 ай бұрын
Good morning Fran hwry l need work WD you lm mknk
@user-pq4yh2fu6f9 ай бұрын
❤❤❤❤❤
@user-pq4yh2fu6f9 ай бұрын
Wer you my frand NYS to match
@user-pq4yh2fu6f9 ай бұрын
Im making
@jimmyroos1677 Жыл бұрын
I change the allu bolts with the 722-6 transmission bell housing steel bolts, had a couple of oil leaks, after this no more problems.
@GaryFerraro Жыл бұрын
722.6 You change the bolts?
@jimmyroos1677 Жыл бұрын
No ,I exchange the aluminum bolts for the steel one's out of the 722-6 box ,u can tighten them properly without them breaking off.
@richbenzer8330 Жыл бұрын
Great vid! Thanks for posting these. Can you post a parts list for the rebuild kit please? I have a 2006 ML500 I bought cheap with a trans that works occasionally, slips, doesn't want to engage, I figure it needs a similar rebuild. I redid a conductor plate/TCM on an 04E500 ($900 car, very nice otherwise) that solved that problem but have not torn into the guts on these boxes. Your vids on the 722.9 are awesome!
@LynxStarAuto Жыл бұрын
The inductor plate on a 722.9 is a totally different animal than the 722.6. On the 9 speed the transmission computer is part of the plate. It's a 4 figure part, and locked away behind TRP. TRP is what Mercedes calls Theft Relevant Parts. You need to have a commercial garage keepers insurance policy, as well as be bonded to purchase the part. It will not otherwise be sold over the counter. Finally, the part must be new as a used one cannot be reprogrammed to another vehicle. At least not through official channels. There are "hackers" out there that use black market tools to clone a used module but good luck. They are harder to find than hens' teeth, and in my experience it will work, but the OBD system will have glitches later on.
@richbenzer8330 Жыл бұрын
@@LynxStarAuto thanks for the reply. I have actually installed a reprogrammed used CP/TCM in a 722.9 and it works fine so I’m familiar with that process. This other vehicle has lost fluid pressure but the CP/TCM controls work ok, just doesn’t have enough pressure to do transmission stuff. Rebuild time! Your vids are awesome, I really enjoy and appreciate your work.
@silver-blz31125 ай бұрын
Do you have a part 2 of this, where you show the problems and put everything together again? Keep going!
@AhmedMohamed-hk3io Жыл бұрын
Great Job 👌 CGMB can help you a lot Gary for VGS virginize
@infocentrousmajac8 ай бұрын
you need to invest on a better camera and better illumination. Transmission repair requires not only knowledge but bery fine image detail to show damaged parts. I have learned a lot from your videos but the image quality can be improved. Keep up the good work!
@Innova_1979 Жыл бұрын
In this scenario; is the point that the transmission shop says I need a new transmission rather than the individual component repairs? Seems like a lot has went south on this 722.9. Being the owner of a non-4-matic 722.9 that occasionally has a jerky shift from 1-2, this has me interested. Please keep the Benz 722.9's coming! Lots to lean here.
@user-pq4yh2fu6f9 ай бұрын
very good my frand wr you form
@GaryFerraro9 ай бұрын
I live in New York
@user-pq4yh2fu6f9 ай бұрын
@@GaryFerraro lm from pLstyn
@jimmyroos1677 Жыл бұрын
Hallo Gary ,if u could maybe help, I've got a Mitsubishi V4A51 Auto box, it won't shift into 4rth gear ,ie no response to 4rth gear no matter in what position the overdrive button is in .the o/d light does function correctly, the Auto lec said no problem, it's in the box .I fitted a complete different valvebody inc solenoids, no difference, new speed sensors no difference, I've stripped the complete box ,can't see anything wrong. No fault codes, don't know where to from here !!!.
@christopheredwards3 Жыл бұрын
Aren't the aluminum bolts replaced.i thought they were one time use.
@basketballjones67825 ай бұрын
@ 2:05 So, basically, you had codes indicating the typical conductor plate issues these transmissions are well-known for, and you decided it would be a good idea to just rebuild the whole transmission. Mmmmkay. Thanks for reaffirming for me why I will never take any vehicle I own to a repair shop but instead do all my own work. Even if I have to buy a bazillion special tools and electronic gadgets to work on a modern car, I'll still end up paying far less and get much better results.
@GaryFerraro5 ай бұрын
The title of the video is slips in 4th, conductor plate will not cause this, internal problem
@sukiiish6 ай бұрын
What if transmission have plus 1 liter oil. Will be to much presure ? Or will be damaged transmission ?
@GaryFerraro6 ай бұрын
Shouldn't cause to much damage, may shift erratic if solenoids can't exhaust fast enough or may come out of the vent when hot
@igotaction Жыл бұрын
Doesn't that take the blue 134FE fluid??? Is it that burnt I know you said it looked like it had been worked on.
@GaryFerraro Жыл бұрын
Thats what they say, 7G Tronic Plus. Premium synthetic is good
@stics412 Жыл бұрын
Shop says torque converter lock issue or transmission on this same transmission. No codes reported. Would you recommend changing the torque converter. The issue is vibration at stop. All mounts replaced. Thanks
@GaryFerraro Жыл бұрын
does it seem like it wants to stall when coming to a stop? Driving no shudder?
@stics412 Жыл бұрын
@@GaryFerraro It stalled once maybe twice had to put in park! Rides smooth but sometimes it jerks. No noise while driving only vibration on brake
@pedromfonseca1 Жыл бұрын
Nice video! Just a quick question. I have a Mercedes GL also with a 722.9 and when doing a transmission service I found copper/bronze filings in the oil pan. Any idea were the filings would be coming from? Thank you in advance
@GaryFerraro Жыл бұрын
I'm thinking converter, was there a lot in the pan?
@pedromfonseca1 Жыл бұрын
Yes there was quite a bit. Is this something I should worry about? I did have faults for torque converter lock up. No fault now.
@GaryFerraro Жыл бұрын
@@pedromfonseca1 Converter maybe on the way out if pan had a lot of Debris
@pedromfonseca1 Жыл бұрын
Gary thank you again for the quick reply. I sent the torque converter out to inspect and rebuild. They said that there was nothing wrong with it. Looking at your video several times and I just don't see any copper or brass. Could it be inside the transmission oil pump or oil cooler?
@pedromfonseca1 Жыл бұрын
Looks like it could be the washers on the planetary gear set.
@user-tz9bd3kh4f9 ай бұрын
Hi Gary from Belarus. It's a great video again. But I have some problem with ML 350. He had a torque convertor vibration when speed was from 75 to 90 km/h. We rebuilded torque converter, checked all clutch clearences and cleaned VB, new oil and new filter. And after this we have rpm rising when 1-2 shifting and sometimes hard 1-2 shifting. I did VB vacuum test and found that supply pressure regulator valves had 14 Hg instead 18 Hg. Is this a key of my problem? What do you think?
@GaryFerraro9 ай бұрын
to me 14 inches of vacuum is low
@user-tz9bd3kh4f9 ай бұрын
@@GaryFerraro thank you and what I can to do to rise vacuum?
@GaryFerraro9 ай бұрын
bore may be worn out, I do valvebodies in everyone i rebuild now. I bore is worn out, oversized valve will need to be installed, you can se what Sonnax has for this unit.@@user-tz9bd3kh4f
@illyapalamarchuk352510 ай бұрын
Hey so I was doing some donuts on dry asphalt and I heard a loud bang and now no drive or reverse gear what could’ve broken?
@jacobpoucher4 ай бұрын
Lol
@RuCuber Жыл бұрын
Can you please tell us how much it costed the customer to get this kind of repair done?
@GaryFerraro Жыл бұрын
overhaul the unit or a transfer case repair?
@RuCuber Жыл бұрын
@@GaryFerraro I mean the price of the master kit and the valve body + cost of work done for the transmission
@GaryFerraro Жыл бұрын
@@RuCuber around 5 to 5.5K
@enriquecastro23524 ай бұрын
very good video. I have a question, I have been working with a 722.9 gearbox for more than 1 month, I changed all the clutch discs with an international pressure master kit, everything new, the orings and rings are also new. I have a leak in the K2, the K2 clutch engages but loses pressure. Perform the test with air using the test holes indicated in the manual. Has it happened to anyone?
@GaryFerraro4 ай бұрын
If you check just the drum is it ok
@enriquecastro23524 ай бұрын
@@GaryFerraro Yes, just check the drum by sending air through the shaft and the drum does not leak. but when I carry out the test through the hole in the box, the drum applies but it is not applied, the air comes out
@GaryFerraro4 ай бұрын
very hard to get a solid air check on the drum, i have an air check tool that i use. Did you air check through the pump support before loading everything into the case@@enriquecastro2352
@enriquecastro23524 ай бұрын
@@GaryFerraro The K2 loses power through the axis that goes to the converter. Is that normal?
@GaryFerraro4 ай бұрын
it may yes@@enriquecastro2352
@edelindimitrov3922 Жыл бұрын
What is the torque spec on the long bolt
@GaryFerraro Жыл бұрын
Never really looked that up, i just tighten it down snug and give a little extra and leave like that
@alexandercleve53166 ай бұрын
part number on the outgoing shaft for the front differential?
@GaryFerraro6 ай бұрын
You mean what the front drive shaft splines into
@alexandercleve53166 ай бұрын
@@GaryFerraro yes, the one you are replacing in another video, number 19 in Mercedes service documents
@GaryFerraro6 ай бұрын
Not sure there is a part number, not sold separately, i always have to go good used on that. I was talking to another shop once that sourced out a new one that came from poland@@alexandercleve5316
@loganlefley16163 ай бұрын
My transmission suddenly stopped working. Very quiet whining sound when in drive and reverse. Neutral the sounds go away. Park and it makes loud sound like when you engage parking brake or use a ratchet but much louder. Car won’t move at all. 105,000km ?????????
@GaryFerraro3 ай бұрын
So when you put the car in park, it rachets like there is something turning?
@loganlefley16163 ай бұрын
@@GaryFerraro it makes a ratcheting sound but only for a couple seconds. Sounds more like a hand brake but much louder. Like something tightening
@GaryFerraro3 ай бұрын
Sounds like the output shaft is turning and it's ratcheting going into park , Do you know if the driveshaft is turning@@loganlefley1616
@loganlefley16163 ай бұрын
@@GaryFerraro I don’t know if the drive shaft is turning. I think it might be free though because I jacked the car up and the car started moving away like it was in neutral
@gokhanuzun1703 Жыл бұрын
hello how are you i am writing to you from turkey w140 vehicle s320 1996 model gearbox 722.508 vietes transitions a bit hard, especially when switching to 3 and four, what is the problem?
@ebkonuk Жыл бұрын
İlk once resetlemeyi dene.
@gokhanuzun1703 Жыл бұрын
@@ebkonuk nasıl yapacağım
@ebkonuk Жыл бұрын
How to reset Mercedes 5gtronic diye arat,bircok video goreceksin konuyla ilgili.Her zaman ise yaramayabilir,bu ilk asama...
@torrencedupree552510 ай бұрын
Can I put a 09 e550 4matic transmission in a 09 s550 4matic
@GaryFerraro10 ай бұрын
cannot say for sure, you would have to check through the vin numbers
@AsifAsif-xk9nt Жыл бұрын
Your camera please update we don't see clear
@michaelgillette7363 Жыл бұрын
Brand: Exedy Part Number: A78542 Description: Pump Plate; Fits in Bell Housing Pump Pocket Transmission(s): 722.6, NAG1, 722.9, W5A580, W5A380, W5J400, 722.901, 722.666 Years: 2004 - 2018 $33.61
@GaryFerraro Жыл бұрын
Thats the plate when the bellhousing is damaged correct
@iamher6422 Жыл бұрын
So what should one expect to pay for such a job? Good job, though… 😵💫