GD-12S High Precision Centerless Grinding Machine

Main Features
1, The Ontology
Ontology and nine components by m han with FC - 30 senior cast iron moulds.By artificial normalizing heat treatment, natural aging treatment after more than six months, nine processing components using YASDA, MITSUI SEIKI, TOSHIBA, ELB world-class equipment such as a clamping processing, precision can reach micron grade, to ensure that the equipment foundation components and high precision.
Contact us:
www.qdgrinder.com
Email: [e-mail]
QQ: 2140855060
2, Main Shaft System
Main shaft is made of SNCM - 21 h alloy steel, after tempering, carburizing heat treatment then through computer control cryogenic treatment, the surface hardness of HRC - 62 ° above, unilateral effective hardening layer of more than 1.5 mm.FX - 12 s main shaft with dynamic pressure oil film bearing spindle.
3, Wheel Drive Adjustment System
Adjust wheel spindle drive Motor with Japan yaskawa Servo Motor (YAS KAWA) Servo Motor, FX - 12 s speed control 0 ~ 320 RPM nc, to adjust to the best linear velocity, when adjusting wheel diameter changes can still keep the same linear velocity, grinding out the best products.
Servo motor installed on the adjusting wheel box clever design using direct drive synchronous belt, can adjust the wheel in the grinding with play Angle at the same time, guarantee the two pulley parallel all the time, overcome the old type centerless grinding machine with chain more section is produced by the inertia loss and the chain Angle bring many adverse effects, and often to avoid the change chain and zipper spring.
4, Spindle Oil Circulation System
Spindle automatic lubrication cycle oil (advanced spindle oil 10 #) and hydraulic shaping device for the same pump, external fuel tank, convenient cleaning oil change, spindle oil, two circulating oil filtering equipment filter and equipped with a pressure controller, ensure the life of the spindle.
Parameters:
GD-12S
Standard model processing range (diameter) 0.5mm-40mm
Special customized models processing range (diameter) 0.05mm-0.5mm
grinding wheel size(diameter x width x diameter) Φ305*150*Φ120mm
Adjust the wheel size(diameter x width x diameter)
Φ205*150*Φ90mm
Grinding wheel speed
1950RPM
Adjust the wheel speed
0-320RPM
Grinding wheel drive motor
7 1/2HP
Adjust the wheel motor
2.0kw AC SERVO MOTOR
Hydraulic pump drive motor
1HP
Cooling pump drive motor
1/8HP
Wheel feed the handwheel adjustment
3.5mm/转 0.02mm/刻度
Adjust the wheel fine-tuning hand wheel
0.1mm/转 0.001mm/刻度
Table feed hand wheel
7mm/转 0.05mm/刻度
Workbench fine adjustment handwheel
0.2mm/转 0.001mm/刻度
Trim feed hand wheel
1.5mm/转 0.01mm/刻度
Wheel Angle
+5°～-3°
Wheel turning Angle
±6°
Mechanical dimensions
1800×1400×1450mm
Packing size
2350×1650×1770mm
Machine weight
1700 kg
Packing weight
1850 kg

[@nafie-hf6vo]

Can you show how to do correctly setup for support blade front side and back side..?becouse some time I can't get the good setting...at work piece have flat ..and some time have tapper...if i tigh to much it will made my work piecs small at back side and flat at back side..i do little bit open also no get it....erhh im so stress

[@GrinderQiandao]

you can add us our email [e-mail] E-mail：[e-mail] E-mail: [e-mail] Whatsapp: [phone] Mob:[phone] thank you we looking forward

[@GrinderQiandao]

can you send ask email or [e-mail] this is our email we looking ur kindly reply thank you

[@williamhuang5329]

Hanzhen harmonic drive gear , over 30 years experience , strain wave gear , robot joint

[@SunilSunil-zk8qq]

How to wheel chaing

[@mdferdausislam259]

i know how to run this machin

[@rajkumarbhagat202]

Hindi bhasa me bataye

[@红喜刘]

12机