Geberit Type 240 Flushing Valve - Installation

Installation film demonstrates the fast and easy installation of the Type 240 (2018) flushing valve into a exposed cistern. Also shown is the installation of the Type 333 filling valve.
Die Montagefilm demonstriert den schnellen und einfachen Einbau des Spülventils Typ 240 in einen offenen Spülkasten. Ebenfalls dargestellt ist der Einbau des Füllventils Typ 333.
ID: 2205741
If you need technical support, please contact the local technical support team.
Please note: Videos do not replace installation manuals. For installation purposes, please use the respective Geberit installation manuals.
For more information about Geberit visit www.geberit.com
Imprint: www.geberit.com/general/
Disclaimer: www.geberit.com/general/rechts...

[@TabarceaTD]

Multumiri din Romania 🇷🇴🇷🇴🇷🇴 Nu m-as fi descurcat fara acest video ‼️🇷🇴🇷🇴🇷🇴

[@allvan1109]

Merci pour cette vidéo cela m'a permis de démonter le mécanisme et de le nettoyer à fond

[@playtoday9270]

Наложил огромную кучу - все смыло! Спасибо!

[@fotomantrojmiasto1752]

Świetny instruktarz, nawet osoba z dwoma lewymi rękoma da sobie radę

[@Jaro966]

Dzięki, bardzo pomocne.

[@bojer1415]

Installed right now. Toilet again working like new :)

[@Abdulhannan-it5we]

Thank you very much

[@Andrej6397]

Very nice and very useful videomanual. But even though I had difficulties to set the amount of flushed water. I couldn't flush more than 5 liters (no matter how I set the blue thing). It took me quite long time to find out why. The manual says to cut the white tube according the table. According the water level + distance ≥20mm. The sign "≥" means "greater than or equal". So I cut 35mm which is ok according the sign. And that was a mistake. You have to cut precisely 20mm, not more than 25mm above water level !!! Afer doing that, everything was ok. And one more thing: No manual describes where to put back the blue rod which you've disconnected at the beginning. It's not obvious for everyone that you have to put it in the same hole number as the number which you set the black sliding top.

[@brianwithers162]

It would be good if the installation manual shown in the video instructions was available. Searched for it everywhere on line with no success.

[@safyosafyo7141]

wow.. nice

[@tvermeer5703]

Is it necessary to cut/saw the top off (after measuring)? What happens when I don't do this? I haven't done it now, and it seems to be working. (The top is 2 cm above water lever.) Thank you.

[@gitfunfel9849]

i have instaled the flush valve but it not works properly. the problem is- when i flush water i have to press the button all the time because when i release the button water stops flushing. why? what to do to fix it?

[@agreatd]

What do these numbers 1-4 at the bottom (blue slider) do?

[@grzegorzbadziak2690]

Hello. Please provide the catalog number of this water supply valve for flushing cistern. Thank you

[@tomaszwilk4946]

Bardzo fajny i pomocny filmik. Jedyne do czego mógłbym się przyczepić na filmiku jest pokazane ze podczas napełniania zbiornika woda wypełnia rurę przelewową a nie powinno jej tam być. Zabrakło mi również instrukcji regulacji małego spłukiwania, aby ustawić 3l chyba że to idzie z automatu skoro duże spłukiwanie ma 6l.

[@jamessail6586]

Lux

[@user-ng6qt4ru6b]

Θερμο υδραυλικός

[@69PlombierChauffagisteRamoneur]

#69PlombierChauffagiste

[@toninae2387]

No gasket between the base and the system. Kept flooding until I realized that.

[@dariuszwalasek2265]

Ok dzięki