No Neutral Smart Light Switch UNBOXING AND COMPLETE SETUP

[@GeekStreet]

Make Your Smart Home Even Smarter with Tuya / Smart Life Tips + Tricks kzbin.info/www/bejne/eIe1e4yQjJKqoc0 If you don't have a neutral wire then there are other options Smart WiFi Light Switch HACK kzbin.info/www/bejne/e2qWoJx5edWfiqs No Neutral Smart Light Switch kzbin.info/www/bejne/mqa2d416h9-sbKc Zigbee Touch Smart Switch kzbin.info/www/bejne/pZCyZnuahtRrq5I ✅ Don't Forget to Like👍 this Video, make a Comment✍and Subscribe ▶ it makes these videos possible 😊

[@bagarrao5406]

HEY, i bought one of this wifi switches, and when i connect with the app work fine, but every single time i press the "manual button" it resets by itself, how can i fix it??

[@JohnnyPacmanFitness]

⚠️ Hi! Great video. I just installed the smart switch in my bedroom, which has a twin switch connection, so 2 switches operate the same lights. I replaced the dumb switch with the simpler connection by adding the common to the Neutral whole and L1 & L2 to L and L1 in the smart. The issue is that the other dumb switch doesn’t operate the lights anymore. Any ideas why? Maybe because I connected the N to the common?...

[@landwomble]

Super helpful, especially the part with the capacitor fitting.

[@madaddams]

I fitted a switch a couple years ago that needed a neutral wire; carpet up in the room above, and two holes in the floor the get the job done. I've been reluctant to do the lounge lights because of furniture in the room above. This is so simple in comparison... Thanks for clear instructions!

[@alanpatterson2384]

A word of caution. The backbox needs to be of a depth of at least 25mm (and even then it is very tight).

[@AvaGrowth]

Before seeing this, I was putting the capcitor in the light switch 😂 I was like, it won't close, lol😂😂😂

[@GeekStreet]

😅

[@immis8894]

Amazon is now selling an updated version of this WiFi Smart Light Switch. This new version comes with a Neutral Terminal on the Light Switch and also a Capacitor in the box. If you have a Neutral Wire at the Light Switch box then this goes into the Neutral Terminal and the Capacitor doesn't need to be installed at the Ceiling Rose. If you only have a Live and Switch Live Wire at the light switch box then you just disregard the Neutral Terminal and terminate the Live Wire to the "L" Terminal and the Switch Live Wire to the "L1" Terminal and you must install the Capacitor at the ceiling rose to stop the light from flickering/buzzing

[@GeekStreet]

Thanks for the info

[@jessemahabir7760]

Ive had these switches for about a month now and every 3-4 days or so, the switch will complete cut off and becomes unresponsive, the only way to get it working again is through my breaker switch... Is this a common problem and if so any ideas to fix it? Thanks

[@Abi161]

Where do you put the capacitor if you have downlights?

[@GeekStreet]

At the first downlight.

[@thanhtam23]

@@jessemahabir7760 mine have same problem, did you solve it? did you install capacitor btw?

[@frankwoods2660]

Best explanation ever!!!!....on wiring these things up....bar none!! Thanks. So the capacitor charges when the switch is on and maintains a supply to the switch ready for activation through the app. Am I right? Never realised a capacitor would hold charge for so long.

[@vakilll]

Best video i ever watched on youtube ! Rly nice work man,regards.

[@GeekStreet]

Thanks for the comment much appreciated!

[@physixger]

Be careful when testing live wires with a one-pole phase tester - they can give a wrong result when the ground you are standing on isolates too well. This can very easily lead to wrong results and grave accidents (50 Hz AC gives you ventricular fibrillation very quickly; which will render you dead in case no one finds and resuscitates you successfully). Always use a two-pole tester (like a Benning Duspol or similar) which you confirmed to be working on a live wire before (!) to determine the system to be not live before touching, and use one of these new contactless phase testers ("beepers") to roughly check if there is AC present. Also, block the fuses before working on the system so no one puts them on accidentally.

[@GeekStreet]

Thanks for the info

[@MurfatlarAII0]

This made it all a lot simpler for me. Many thanks ! ✅💪🏼🎩

[@GeekStreet]

💪

[@JohnnyPacmanFitness]

From time to time the switches go offline and I need to trip the DBs a few time until I get them to respond again. Anyone getting the same issue? Any ideas about how to get the switches online without touching the DB?

[@hamsterdogcat]

Why can you just install the capacistor right behind the switch it self?

[@madnlooney]

For those who get a 2 gang version watch out for the load drop per gang compared to this single one. I think it's from 300w to 100w. Yes I didn't check and blew the switch board when turning it on

[@muhtasimfuad1945]

what did you run with it

[@madnlooney]

@@muhtasimfuad1945 they were normal 40w bulbs, now switched to leds

[@emiel1976ep]

I was looking for that. Thank you.

[@muneeral-yousufi4889]

Best and excellent explanation, never I seen like this explanation before. One billion like and subscribe👍👍👍👍👌🌹

[@stevelee9924]

Firstly, whoever installed the light switch should have sleeved the Blue wire with Brown sleeving as per the Regs. Secondly, do not use this type of voltage tester, dangerous and should be taken off the market in my opinion.

[@jordiboichav]

All I'm going to say is thank you iv spent days going over the schematic and by the diagram it suggest putting the block on the wall. Well say no more it works!

[@jboy6944]

Hi i just ordered this device and installed it, but when i turn on the power, the capacitor makes a buzzer sound. How can i eradicate this problem?

[@iRBrummie]

I also have this problem :( did you ever find a solution?

[@madnlooney]

Likewise. I wonder what the value of the capacitor it to maybe find an alternative

[@nkonovski]

same here, so I wondering if it come from the quality of the capacitor or need to be attached to another gang (mine is 2 gang switch and I put the capacitor to L1 line as in the schema)

[@jboy6944]

I reckon looking for a capacitor that meets your home power supply

[@philwebb606]

Don’t fit the capacitor

[@yousafmalik1508]

Good, clear instructions, job well done.!

[@GeekStreet]

❤️

[@pieczarki-mushrooms8927]

The best tutorial in the web. I am just wondering why the hell manufacturer added external capacitor? It would be much easier to have it build in the switch itself and save those ridiculous rewiring of the lamp - stupid. Original instruction is useless, this tutorial helped a lot.

[@andreelliott6161]

You are my go to gadget channel good work Geek street 👍

[@dimigen]

what happens if i don't connect the capacitor to the lamp?

[@piggintouring]

Your BLUE cable should have Brown sleeving placed on it , this will show that this cable becomes LIVE when switched on.

[@train4905]

Dear sir ,a most exellent video ,,by far the most clearest ,explanation,and demo.video so far huge thanks

[@andypickles9007]

What is he spes of he capacitor please

[@train4905]

Exellent demo😊

[@GeekStreet]

Thanks

[@nerdkidleo]

what was the capacitor for?

[@komodoification]

This is great. Is there a dimmer version too?

[@GeekStreet]

No

[@DaSilver87]

Thanks for the video explanation! Really helped me out with explaining about the capacitor! Just out of curiosity, what could happen if I connect the capacitor between the Live wire and the switch?

[@SqueamishPuppet]

Did you ever try this? I think that is what I would need to do. I have switched outlets so I'm not sure how to put the capacitor between the light.

[@Screwballus]

In the Netherlands, Blue is Neutral and black is the switching wire. Something to consider.

[@mojo5845]

Can I still use the Wi-Fi without the capacitor

[@cecello79]

Nice and clear video explanation! I have a question: if I have 2 or more light points connected to the same switch, do I have to add a capacitors to each bulb? I’m a bit confused because light bulbs are connected in parallel and in my case I don’t know which one is the head of wires! Thanx man!

[@rohansootarsing9325]

Thanks got two of these now. Noticed that one seems to emit a high pitched whine from the capacitor

[@GeekStreet]

Could be faulty, contact the seller and ask their opinion.

[@vicentecalderon3615]

Same here... noise coming from the line with the cap installed and can't mute it. Somebody else experienced this?

[@iRBrummie]

im having this problem, was you able to find a solution?

[@alienmi2mi876]

Dude, I don't usually comment, but let's just say I had to like and comment this video!

[@GeekStreet]

Thanks 😊

[@jordianrenaldi436]

Hi sir can I ask what happens if we don’t install the Capacitor?

[@kianxinlee3370]

Up

[@stueyevilcat9983]

Love the video. Could anyone swing any advice as I have a 2 gang smart switch and live in an old house so struggled with the wiring. thx

[@mytubeek]

Ever get this sorted

[@stu600cc]

Do I need extra deep box for these or does it fit standard boxes for plaster board

[@zedman442]

Good concept. Potentially may have an impact on insulation resistance numbers when a test on the circuit is done in the future like an EICR.

[@lukedodds8265]

Something like this would have to be disconnected surely before doing an IR test

[@SME_Ste]

@@lukedodds8265 if you knew it was there yeah you would. LN to earth for this reason

[@BB-gx7gc]

I have one switch that turns on two ceiling lights, do I need a capacitor for each one?

[@instaboiidsg2117]

No only one

[@Adam-be3my]

you only need one since they are connected parallel, the capacitor can still operates for other load as well

[@BB-gx7gc]

@@Adam-be3my that’s great thanks for the help

[@stevelee9924]

Same in the ceiling rose, the Blue wire connected with the Brown core of the flex should be sleeved Brown.

[@LimaOscarBravo]

If I get a capacitor seperatley can I use this same process with any smart switch which requires a neutral? I'm struggling to find homekit enabled smart switches that don't need a neutral and don't require an additional hub. Thanks!

[@giovanniklassen]

I think the main purpose for the capacitor is if the light flickers a lot

[@Almatrodi]

Thanks so much. How about if each switch is connected to 12 led lights?

[@2cows534]

Been thinking about putting a couple of these switches in the living room, very helpful video. Thank you very much

[@BernardShin888]

I followed all instruction but cannot get any blinking??

[@strafo8124]

Does the capacitor have a direction or is it indifferent? From the video it is not clear

[@GeekStreet]

Anyway is fine

[@strafo8124]

@@GeekStreet thx

[@kactive659]

Looked at the link and there £18.99 each seems cheaper till you think about putting them all around the house and it ends up being £211 thinking about getting some for the bedrooms tho just need to see if I’ve got a neutral wire on my switches or not 👍👍👍

[@mohammedshaheen13]

Clear explanation. Thank you for making it easy and simple.

[@GeekStreet]

Glad it was helpful!

[@nebsonic]

I have the similar one, no neutral and cap connected, but the device shuts down when light turns on - seems to short itself and disconnects. Mine clicks as opposed to yours, so the relay is inside. Not sure if mine can work without neutral

I want to give you a hug! thanks a lot!

[@Ukman-england]

Can this control a socket from a wall switch to I need to open up socket and put wire in like light

[@GeekStreet]

Yes as long as the socket is smart.

[@Ukman-england]

@@GeekStreet so I need smart light switch and smart socket to control outside light plugged into a outside socket

[@neildelgado3054]

Hi thanks for this video! May I know what's the specification of the capacitor? Did it come along with the switch? I checked out the item at Aliexpress it seems that it only include the switch.

[@RobertoLavoie]

I got one now and it has the capacitor

[@neildelgado3054]

@@RobertoLavoie thanks for the info!

[@jcai922]

Hi there the capacitor install before the LED driver or after?

[@giovanniklassen]

Before or else it might blow up😂, if its LED i don't think it would be necessary the main reason for the capacitor is if the lights flicker a lot then the capacitor should maintain the power up

[@delidag]

Thanks for best useful information

[@markyoung2151]

Hi, thanks for this video, makes so much more sense than the average instructions 😂 I've installed and all seems to be working well apart from the fact that the power light on the switch is lit blue when my light is on and red when it's off but your's seems to do the opposite. Any ideas why this might be? Have I done something wrong and should I be concerned? Thanks again

[@GeekStreet]

I wonder if they have have changed the design!?

[@athanasiosagiannidis829]

Hi Geek Street, how many of these have you got installed? Any flickering issues? Also have you experienced any devices dissapearing all of a sudden and having to be recommissioned? Many thanks.

[@saimyooo]

I have the same problem with u. No idea why flickering.

[@gavbarker2]

​@saimyooo i have same problem, was you able to resolve it?

[@chandranv5420]

Great video, as always. I was wondering if wiring done for light switch (10A) can be used for fixing up a power socket? Any ideas?

[@prashp2723]

I have added this switch to my living room with two lights. The light keeps flickering do I need two capacitors. Living room has x2 light fixtures with G9 LED bulb.

[@leulino]

Hi !! Did you resolve your problem? This is happening with me the lights keep flickering when I'm using an LED bulb. That doesn't happen when I'm using fluorescent lamps. Maybe should use another capacitor spec?

[@mikeward4143]

Hi there We have used wago clips to connect all the wires in the celing. Can the capacitor wires go in spare holes in the wago clips or do they have to go on top of the actual switch live and neutral wires, from the light fitting??

[@RossHighet]

Hey bud.. this really helped me.. thank you. Just have one question.. I have a four gang.. so 4 different switches for 4 different lights on the same panel.. they sent only a single capacitor.. and the diagram shows only one.. little confused with that.. what about the other three lights? Does it have to go on the L1 or it can go on any of the lights coming from the switch.. thanks for any help.

[@GeekStreet]

It just has to go on one light.

[@ewdtrey]

It just needs the one capacitor. It's basically what keeps the switch powered when the lights are off.

[@sonnyknekthage2833]

Question about the app. Can you create a scene for the switch to turn on/off the light at sunset/sunrise?

[@GeekStreet]

Yes that's possible

[@db-bv5rs]

No markings for switch live🤔 could get confusing if rewiring

[@te384]

Hi ya, does the schedule function works if your wifi router is switched off?

[@Reza.sohrabi]

The two gang version of this can the lights wire up to it be turned of individually using Alexa?

[@GeekStreet]

Yes

[@tortysoft]

What does the capacitor do ? We have the light never going fully out. Is the switch faulty or does it need a capacitor - none came with the switch. Thanks

[@hakimzah]

Really helpful. Thanks! Btw just wondering is it possible to use google assistant in Android without the google nest speaker?

[@GeekStreet]

Yes you cam do that.

[@alexyh8448]

hello nice video.. can i use it for DC module ?

[@rodelcabale1753]

Thank you for your technical support , it's very helpful👍👍👍

[@GeekStreet]

You're welcome!

[@jonathanhowarth9894]

Had mine fitted for about a year to 6 outside LED lights thst are on a dusk till dawn sensor. The lights come one but i can't use the switch or connect the Wi-Fi. Would the dusk till dawn sensor make any difference.

[@ananthivenugopal5363]

Must we fix the capasitor. What will happen if we do not fix it

[@robertstrachan7372]

Got these installed throughout the house only upstairs seems to turn themselves on, not connected to the WiFi just in case it was that. Could the loop circuit cause the problem with the capacitors at each light?

[@RanTausi]

Hi , capacitor installation is a must ?

[@KurtisBaptisteSVG]

I want to add a smart switch to my outside flood light, do i need a capacitor? Thanks

[@douglaslee3646]

There is a plastic sticking on the white foam on the inside. Do I have to take it out?

[@emiel1976ep]

I have now a double button one and it works great. It has also rf 433 and that makes it even better. I don't know if you have it also on that one. It is easy to setup and I have both on one rf button now. I must switch that to an other button, but I wanted to test it. My lights witch is ad one door, but there is no switch ad the other door in the room and with the rf I can now easily solf that.

[@GeekStreet]

So your one must be WiFi and zigbee compatible.

[@emiel1976ep]

@@GeekStreet no mine is just wifi, but has also rf433 support.

[@jojotalon821]

What if the internet is down can you control it using smart phone

[@haythamalbulushi9640]

Hi this is a very good video thanks Can I use this for my air conditions ?

[@leandrociclidos8998]

Thank you very much for your information is very clear, it helped me a lot

[@GeekStreet]

You're welcome!

[@mustmustosheer4668]

Can I put the capcitor just behind the light switch inside the box or I have to put it close to the source; fan or light bulbs?

[@pranganator]

Right at the bulb

[@VtolVRClips]

if i have a led light above do i need the capacitator still ?

[@volkangezer]

is there a way to close it after 1 sec, not after 1 min (aka inching)? unfortunately our lights are just push to turn on/off (not up down), and I am currently looking for a way to manage that.

[@tejnathadhikari]

Great Video.

[@shaheenhaneefa]

How do you reset 2 way gang switch ? I kept pressing the switch for 10sec+ .. but no blinking

[@rolandeccles4639]

Very helpful 👍

[@Jam8s1]

Fantastic video, great clear explanation on how to fit the capacitor. Thanks

[@GeekStreet]

Thanks!

[@HumeidAlHabsi]

What if capacitor was skipped will it just not work or it will ruin the switch?

[@michaeld5621]

I'd also like an answer to this question.

[@brianherman1455]

@@HumeidAlHabsi did you manage to have this answered?

[@SaintVader]

@@HumeidAlHabsi I use it without the capacitor, the switch works ok manually but I have many disconnections. Maybe the capacitor helps keeping the switch online? 🤔

[@AlexKickham]

Are you sure this fit's in a 25mm back box? The amazon link to the product say the part which sits inside the back box is 33mm? And it looks pretty chuncky in the video!

[@OltraTV-e9e]

can this be done with downlights ?

[@joshh411]

Perfect, thank you!

[@GeekStreet]

You're welcome!

[@mdereen7204]

Thank you so much

[@7amo0o0ud]

So in my living room have 6 led light So how it will work? Meaing for small yallow where i will install !

[@dereknorris2376]

Tuya Smart g10 how to work with senior when I walk in the house to come on can it be done thanks

[@adrianjsv6188]

Hola quería saber cómo haría en el caso de que la luz que quiero poner son 5 bombillos continuos ósea el interruptor encendería 5 bombillos el capasitsdor se puede poner a uno solo ?

[@FaisalMaqsood-i1k]

Hi mate how you doin I have got 4 light bulbs they are connected to one old switch I would like to put new smart switch do. I need 4 capacitors for all the bulbs to connect to one switch

[@Itisinthehand]

What is the load please? What sort of wattage can it handle? I have 3 LEDs and two fans the wattage of which I don't know from memory but that's kinda where I'm at. ( Two toilets)

[@edj]

Do u need to install the capacitor? What is the purpose? Not an electrician, just curious

[@Swenser]

Mine turns off by itself at times. Do you think I need more or less capacitance value? And the high frequency buzz from the switch is a bit annoying

[@jabrique]

Hi, if i have one switch for 3 series of lamp, do i just put one capacitor on the first lamp series? Or do i have to get 3 capacitors for each lamp??

[@GeekStreet]

Just the first

[@siamakbaradaran2581]

Hi , is this switch working with 8 led lights on one loop?

[@mrsiryeah6024]

can i not use the capacitor and not use the neutral or no, sorry i don't know much about electronics and wiring

[@Imanc]

Fantastic detailed review. Exactly what I was looking for. I am planning to use it on a dimmable LED. Can that be done using this switch on Google Home?

[@GeekStreet]

Thanks, you can't dim from the switch but you could use a smart bulb.

[@pennefathermark7423]

Sorry for asking a simple qn. do i need a home wifi system to be in placed before this pairing setup?

[@GeekStreet]

Yes thats right