GENERATOR 24 VOLTS LOW INSULATION TROUBLESHOOTING

[@JoshHogendoorn]

I found this very helpful, Ground-faults are a nightmare....

[@MrPinkWing]

Thank you so much for all your videos! You explain very clearly. I'm doing my first contract as electrician on a sistership, so your videos are super usefull for me!

[@leckyjake]

thank you for watching

[@piinheiiiro]

You're expert in power generation .

[@rohilkumarsaini9126]

Thanks you so much sir for sharing this wonderful and knowledgeable video.

[@leckyjake]

thank you for the support

[@Anna-nr9kk]

Thank you, mr. Jake!

[@adamdeguzman3238]

Thanks for sharing your knowledge! ❤️

[@varatharajan1837]

Nice troubleshooting thanks for sharing your valuable knowledge thank you very much

[@leckyjake]

thank you for watching

[@nagrerelax5602]

Nice one sir Jake

[@ricardopastor7488]

This video is very helpful, thanks to making this kind of video..

[@dilsara5429]

❤❤ Thank you

[@elevationtechvlog3474]

Hello sir your work is very difficult and dangerous...be careful always god bless...

[@geenumaxy9370]

ur good man nice troubleshooting

[@electrotechtv2109]

Thank you for sharing sir

[@kennethlobo4420]

Great trouble shooting video.

[@ВикторияЛирник-я9и]

Thank you So mach. This is good Video

[@sal7777777]

Great video, I really like the content you make specially the troubleshooting videos, they are fantastic. Is there anything you can do to improve the technical editing quality of the videos though, the audio levels are really extreme, on some parts the audio is really low and others really high, sometimes it makes it hard to watch them.

[@gohanmusic4842]

excelente

[@edwardborja3280]

Thank you sir for this vedio

[@alterator]

Fine

[@waynep343]

Did you eyeball the inside of the connector body for casting roughness. Think about if it can be done to remove the casting roughness. Use some 3m# 27 fiberglass cloth tape on the inside of the fitting and around the harness..

[@leckyjake]

i did used the thermal cloth tape for insulating the wires

[@afsalali3961]

Thankyou sir.. 👍🏻👍🏻👍🏻👍🏻

[@joseenricoaguila5218]

thank you so much, very helpful

[@leckyjake]

thank you for watching

[@kevin00861]

Thanks a lot brother for your amazing videos, If I may ask please, Is it safe to unplug & plug terminals to analog control modules while it's still live ?

[@Didier_Lebrasse]

Great Video:)

[@leckyjake]

thank you for watching

[@sudhanshusaini4968]

Sir plz share more troubleshooting videos on generator

[@jorgebravo415]

Flink ship elektriker ⚡⚡⚡⚡

[@afsalali3961]

Pls do one detail video about bow threster sir..

[@leckyjake]

keep on the list

[@tayzaraung4843]

Hello sir,guide me what book is good for eto.

[@islemghz3780]

Hey hope you are doing well, I'm an instrumentation engineer (will graduate this year) i want to ask you if it is possible to work as an eto with my engineering degree (if not then please guide me)

[@leckyjake]

hi, it is always depend on your country. you should check the maritime authority that governs the licensing for such profession.

[@elevationtechvlog3474]

Always remember that we cannot see the current...

[@rafaelhijara9534]

Sir I have also a problem of low insulation of 24 volts alarm..but during underway situation the alarm was okey..and sometimes my 24 volts insulation indicator is flactuating.. Is the low insulation indicator have a problem.?

[@leckyjake]

it depends, you should start tracing whenever it is active.