Get More Power For Your Road Glide With A Stage 2 Cam Upgrade!

[@owdiss1978]

I just did same kit in my 2022 ultra limited 114 engine 475 cam, ss intake manifold , stock intake from stage 1 , stock decat head pipe khrome works slip ons with ripper baffles dyno tuned at 120hp & 132 torque even the tuner was impressed with the numbers!!

[@Rex_S]

My 107 with the 475 made 109hp/118tq. Took me about 3.5hr to install myself on my lowrider. Sound and runs awesome

[@ErikLandrethComedy]

Every town needs a Billy , I have spoken

[@nigelleahy406]

Omg i never heard a harley sound so good. I allways taught small pipes and fishtails and everyone was telling me no no go for the bigger pipes but no u are right. Smaller pipes and them fishtails sound like THUNDER.......... U have great knowledge of the harleys. Thanks very much from Ireland.

[@ProfessionalMonkey]

Thank you!

[@parkeslife4323]

Nice! Grinch is coming along. Can't wait to see what's next. Stage 2 can be louder because the cam changes when the valves open and close. And a higher lift cam allows more air/fuel to flow in to be squashed and burnt. So more exhaust gas comes out under more pressure at a different pulse timing. 👍

[@ncautolink]

I just did mine 475 cam on 2019 Street Glide Special w 114 motor, FuelMoto head pipe and Rinehart 4.5 DBX exhaust w FuelMoto inserts and tune! I love it.

[@scottp2868]

I have the exact same set up, just finishing it all up. What numbers did you end up getting? My numbers are good but the seat of the pants feels way better.

[@hank3859]

I had to replace my manifold because it warped, so I put the SE manifold in, I have true duals from Vance & Hine with Twin Slash slip-ons, S&S 475 also. My Road Glide is a 107 and my tune made 106HP and 117 TQ. And yes it got very loud after it was done.

[@toolmaker5150]

Thanks for the vid. While upgrading a cam plate and oil pump on a ‘20 and up, is not a waste on money, but is not needed. I always hear the argument “you’re already in there” If you have an extra $1600 and are paying for labor, maybe so. A top builder and tuner in my area (CA Bay Area) told me it would be a waste of money for my ‘21 FXLRS. I was only doing a bolt in cam. He recommended a 22xe over the 475. I also do my own work.

[@devinkierski4102]

2011 Harley cvo streetglide 110ci with powervision and s&s 585 ez start cam kit dyno was 109.43hp 118.76tq

[@HappyRamblingCamper]

Love my 2016 UL with the H.O. 103 just hit 64,000 miles yesterday… bullet proof. Compensator at 58,000 miles.. stage 1. Since the H.O. Has a “hot cam” kinda .. i said kinda .. calm down …. Love it ….

[@rpmfreak9150]

Absolutely love the sound. Those numbers aren't really anything, to complain about either! Great video brother thanks for sharing.

[@scottrobbins3410]

Stock should be about 87 HP and 109 TQ. I put the S&S 475 into my 2019 ultra with Rinehart duals and it put out 114 HP and 128TQ. I just put the same cam in son-in-laws 2021 FLHXS with a TBR 2-1 shorty and it pulled 117 HP and 128 TQ.

[@markdurham7046]

The sound is incredible, the lope is definitely Harley Davidson

[@charleycavanaugh5414]

I love it when you Lie Like a rug about where you ride your bike . God Bless you and your Family . Amen Love ya Bro.

[@williamvaughan6448]

I did the S&S cam chest as well on my '18 Road Glide Ultra, but went with the Zippers 468 cam. I also went wide band on the O2 sensors, SE Pro Tune Plus and Power Vision 2B. 107 HP and 118 torque with 4.5" Tabs. Yes, much louder after the cam!!! I love the lope with the 468 but the 475 may have just a teeny but more.

[@tommiller8714]

Grinch performance upgrades coming along nicely; S&S 475c Cam Chest Kit is awesome! Do one more thang to the "Grinch" to complement the Stage-1/Stage-2 upgrades: In short, get selected HD OE "plastic" parts off the bike. 1. Replace the plastic OE intake manifold with a 55mm aluminum intake manifold (S&S and HD-SE offer these). 2. The cover on top of the transmission...replace the OE plastic piece with a Trask M8 Checkvent (metal and it properly ventilates the crankcase, plus it looks good, available in chrome and gloss black). 3. Cable Clutch adjuster...replace the plastic OE piece with a metal aftermarket piece (about $50, I believe I got mine from HogWork). Other: for air/oil cooled Touring...Add the Fan (HD or Thundermax) to the Oil Cooler and flash ECM (if stock tuner), or ensure box is checked if using Dynojet or TTS. If using a Thundermax ECM, super easy. Just saying! Tom M., 2023 RG-ST 117 Stage-1. S&S 2-1 Sidewinder (no cat; dB reducer installed for now until Tuned), S&S 55mm intake manifold; HD-SE Extreme Ventilator a/c; Trask M8 checkvent; HD oil cooler Fan; numerous other upgrades to Lighting, Audio, Bars, Suspension, etc. Planning on Stage-2, considering the Redshift 472 Cam and the Star Racing 485 Cam.

[@reginaldrobinson4810]

New to the channel and love the content have been binging a lot of the old videos and I appreciate the light, but informed of nature of them.

[@jesusuribe1660]

Great video! Learned a lot man and it went towards my goals with what I visioned in doing to my 22 SGS. Answered some of my questions from your previous video. Thank you for the knowledge!

[@ericnay7733]

I’ve got a 2022 road glide standard 107 in reef blue with a Bassani 2 into 1 mid length and Arlen Ness big sucker. I originally wanted the s and s 475 because it chops so hard and sounds amazing on top of its performance. But it was during Covid and they were back ordered. And I had money burning a hole in my pocket bad. So I went with the zippers red shift 468 instead. Cant say that I’m disappointed. It doesn’t lope as nice but it still has a good sound. And the numbers out of the 107 with a screaming eagle tuner are 119 ft/lbs of torque and 106 horsepower. So.. yeah. I’m happy! Ride safe-ish!

[@rubencarrillo6638]

Sweet man. Mine is 114 RGS with the THeader mufflers, jackpot header and STAR 30/30 cam. Numbers are 119.8 hp and 138tq. It’s fun to ride.

[@duder280z]

That idle is the #1 reason I want to go with an S&S 475 when I do stage 2 this winter. Fuck yeah!

[@lastnline1]

121 hp 122 torque on a 114 stage 4 screaming eagle kit , power vision tuner khrome werks 2-1 exhaust

[@nightwolf5909]

Sweet looking and running scoot.. 131ish T-Man pistons and rings with T-man 3262 and D&D 2 into 1, Power vision turner 156 torque and 156 HP 2020 Road Glide special

[@ProfessionalMonkey]

Whew! That’s a bad girl!

[@ricklustig6613]

You did a great job of explaining the differences in a most entertaining way, lol. Kudos from the old biker in the far great white north :)

[@ckthompson7928]

Without going into a huge deal about cam operation...... Basically, the more displacement, the taller lift and longer duration, the biggest trick is getting your cam for the rpms you ride . I'm sure there's lots of people that are saying the same thing.... That 475 is a really good cam for the m8 good choppy exhaust note, and from 1600 rpm- to 5800 rpm you'll be smiling ear to ear..... The Grinch that stole torque+ horsepower.... Be a hell of a sequel... Enjoy that beast

[@wcraiderevo8078]

Methinks he's done that install a time or three...

[@Jim_Berry]

Sounds great! I would name it “Green with Envy”.

[@davidellis7446]

I got married on a 64 Panhead! Getting St2 on the streetglide next month! Hi from UK

[@bfereclipse156]

Gawd damn she sounds amazing bud!!!

[@jasonholby8915]

I am curious to Dyno mine. I bought it with the work done. It started as a 107, was bumped to a 114. So my guess would be it was just piston and jugs, so a shorter stroke bigger bore 114. Plus a RS 468, D&D 2-1, 5.5 injectors and a Fuel moto ac/dc air cleaner.

[@MinnowMoto]

Great video. I love watching those guys work. Amazing.

[@freedom6919741]

124 dark horse crank SE 64 mm throttle body Cycle Rama 480 cam S&S sidewinder 2 into 1 stock heads Baker Grudge box 133/146. Makes 145 ftlbs at 2500 rpm. It built for 2 up touring.

[@Mongo11b]

The LRST is the exact reason I’m super critical on Harley parts. Everything they sell is EPA compliant.

[@rollinggordo9945]

Put a Feuling 543 cam in my 2011 Fat Boy. Best thing I ever did for it. It finally has pull and the lope sounds awesome

[@michaelterry885]

Flhtcu twin cam woods 555 v&h power dual head pipe 4 inch jack pot outlaw mufflers and Arlen ness inverted air cleaner rest of motor stock went from 75 hp to 95 and 90 torque to 100 awesome video like the color god bless

[@stinde666]

NOW it has the great gallop 🎉 sounds awesome 👍

[@samfrankow3167]

It might be the Canadian in me, but I'm wondering what the plate reads?

[@RoadglideDad]

My 107 puts out 110 hp & 118 torque w/ Klockwerks Dominator full exhaust Performance inserts, Red shift Zippers 468 cam. Love it.

[@okiemale1589]

Hopefully I only have another 4 weeks of waiting for the parts for my 2015 Ultra... Going Screaming Eagle stage 4 so... can't wait...

[@csolivais1979]

​@@Peter-nm1psbecause now it's not as "slow" as it was before.

[@csolivais1979]

@@Peter-nm1ps meh, people like what they like. Some people would prefer to have a Porsche or Lambo, some would rather have a '68 Chevelle. Different things for different people.

[@THEM_ROBINSONZ]

2020 road glide S&S 128 All the same stuff as my road king 138hp 148tq

[@SOONERS918]

Those are good numbers but a lot of people only look at numbers and fail to see that torque dip in the curve

[@freedom6919741]

It’s the space under the curve that matters.

[@mrfoomutt]

LMAO. Loved it Keeping you busy.

[@byoung8528]

Running the 475 in my 107 for three years with a F/M tune with decatted head pipe. went through four different sets of slip ons and a definite improvement in performance but the clutch side lazy pipe did not have the velocity to push the exhaust gases away from the bike. Sitting at a light or in rally traffic it was borderline unbearable, put a Khrome werks outlaw 2into1 and I have found the performance and sound I was looking for and no longer asphyxiate the wife, although I do snap her neck with the torque.

[@joesainato8051]

I bet it runs good. Just my two cents with those FM tunes take it to a good dyno guy. You may not get a whole lot more in terms of numbers but it will clean it up and get you the power how it should be. It’s a good starting point but my 107 was completely different after tune

[@Brav-bg9kq]

This was really cool to see. Thanks!

[@richardrussell500]

Did he check the crank runout? I have read that a run out greater than 5 thousands of an inch is what causes premature oil pump failure, and in turn causes sumping issues.

[@williamvaughan6448]

Ideally, both crank and pinion runout should be checked for Total Indicated Runout(TIR)....that being said, S&S says not to install their cam plate if you're over 5 thou, under 3 thou if you're wanting gear drive. Harley is actually pretty good about checking it before upgrades. May depend on the shop, but always ask.

[@HarleyGeezer1954]

I went with the S&S 465 for better torque on the 2020 RG. I went with the cam chest kit and did the entire low end. I even did the black pushrod covers. The only thing I regret is the Thunder Max. I should have used the Dynojet for better fine tuning. My gas mileage sucks bad.

[@rickyhawkins7407]

I having the same issue with my Thundermax. The bike seems to run fine, but my gas mileage sucks. I had my dealer do the 114 Stage 4 when I purchased it in 2018. I need to find someone in my area who knows how to tune a Thundermax.

[@bigblue3568]

Stage II can be easily down in just a couple of hours... or less. Always fascinating to watch techs pull push rod covers, turn the rear wheel to watch them move up and down to find TDC before cutting stock rods... ALL you have to do is take off cam cover which you have to do anyways and use the timing marks on the sprockets for exact TDC. After market cam plates better? Sure but local shop owner has never seen a stock cam plate fail in over 20 years.

[@vincentmurante5142]

121 torque 112 HP on a 2017... 107 cu...tts tuner... Rinehart 2-1-2 head pipe... 4" Rinehart muffler....Rinehart big sucker air cleaner with a s&s 475

[@jasonbreedlove495]

It's good to see how it does on a similar build. I'm torn between the S&S 475 and the zippers 468 in my 21 RKS. Running jackpot 2-1-2 and 4.5 TABs and of course zombies. Dig the lope bud.

[@gottagowithjoe1]

I have the 474 rocket cam on my 2019 114. 124hp and 134tq

[@riskymedic4237]

I will be down at Those Dyno Guys in June for my Cam and tune on my Victory Cross Country Tour. I will see how much louder and how much power hes able to get out of mine. Running Andrews cams and Vance & Hines slip ons.

[@stanwerner7484]

I wonder if "Porting the heads" would increase the "Numbers" ?

[@ProfessionalMonkey]

I’m sure it would

[@canttalk]

Mine does 116 hp and 130 torque with s&s 475 stage 2 stock throttle body. I have 2-1 exhaust powervison tuner and target tune though after the dyno tune. Before dyno tune 102 hp and 120 torque from a fuel moto emailed tune they sent me. I have a 2019 breakout m8 114 by the way.

[@775summit2]

I did the Harley torque cam got it tuned and it hit 100 horse and 120 ft lb on a stock 114

[@RobAshton44]

I got the 475c cam in my 119 GREAT CAM . POWER AND SOUND!

[@Wolfpack6D]

That is what I want mine to sound like

[@jameszee7585]

I realize my opinion really doesn’t matter….😉😉😉 Really impressed with the sound of the exhaust. I never usually like any type of fish tails… Your bike sounds great!!!! Ride safe, hopefully we run into you at Sturgis again…

[@joshwagner8954]

I just did a stage 2 on my 2019 RGS...I was concerned about keeping my extended warranty so I went with all SE stuff, Stage 2 torque kit. There's noticable gains but it really wasn't worth the cost. I kinda regret it and wish I'd gone aftermarket and definitely not the SE tuner.

[@ProfessionalMonkey]

Sorry you're disappointed, but I get wanting to preserve your warranty.

[@travisgray3331]

131 is under warranty…yes epa compliant but maybe mention the warranty it’s under. 114 no more warranty…but you knew that💪

[@bdtodd50todd38]

The idle does sound great.

[@kurtfirestone2761]

475 is a good cam for higher RPM riding if you want mpre low end tq go with the 465. It depends how you ride

[@TweedleD]

There's nothing tighter than a good cross thread 😅

[@garyehrhardt3136]

LOL

[@blackedoutbandit]

Mine is just a stage 2 with the woods WM8-22X-E and tuned with dyno jet. It make 114hp and 128 torque

[@KenMrKLC]

2017 SGS 107 V&H Pipes DeCat stock head pipe Dynojet UYpdated oil pump HD hp cam 109hp 120tq

[@michaelsturdivant9571]

I bet your neighbors dislike you sometimes. But sweet sounding ride.

[@1badsteed]

Sounds incredible! Wubda wubda wubda!!!

[@dwight072]

I have a 114 S&S 475 on power vision D&D 2:1 and it made 118hp and 131tq.

[@rynomotorsports3737]

If you install the 2.5in louvered baffle it will tone down the sound and help your torque at 2-3k rpm while maintaining the flow in the top end. I didn’t realize your in Florida as well !!

[@markmcintosh7095]

The numbers seem good for a cam swap.

[@TheOUboy]

Sounds great

[@DrHarley]

My 114 when it was only Stage 2, 114 HP and 130 TQ. after the motor swap. 140HP and 160TQ.

[@TheMilitaryBiker]

Looks and sounds awesome mate..tidy! ✌️

[@ejdtm]

The 131 EPA = warranty. Green paint looks great

[@crazyeyez1502]

When you say he starts all dyno sessions on a stock tune, does that mean he overwrites you autotunes back to a factory tune?

[@robertperry5272]

Great Video

[@genekelley7579]

🛑🛑 I do like the “ loping sound” of that cam. 👍 I would have liked to heard the Zippers Cam. I have heard folks really talking them up, however I have yet to run into one on the road. Great Build, Buddy!! I like how you are going about making the bike “unique”. 👍💯

[@aswmkid3]

I'm starting to think if you can't play hot for teacher to the rumble at idle its too smooth.

[@ProfessionalMonkey]

Exactly!!!!

[@dannydlowbikertv]

Very impressive on hp, and man that thing sounds great. Very nice ... I'm doing andrew 57h in my road glide this week. I just hope it sounds like yours, I don't even care about the power. Lol

[@williamrose8944]

EGS 107 s/s 55 mm aluminum intake stock pipe modified, 30/30 , Arlen Ness Big sucker Tab 4.5 with 2.5 baffles 117 hp & 120tq

[@johnstrickland9545]

The bike sound's awesome man

[@Jeffmd2020]

I have a 2007 street glide with the 96” 6 speed and I’d love to do a cam job on her but when it comes to cams I don’t know shit about fuck!! I know I want a nice beautiful lope but having the smaller fuel tank on the 07 I don’t want to sacrifice much MPG’s!! I’d love to do a gear swap also to get rid of any potential cam chain tensioner issues in the future but like I said I’m completely clueless when it comes to picking the right cam!! Any advice would be greatly appreciated brother!! LOVE the new body swap by the way!!

[@Mr07explorer]

Not enough. Needs a sneaky pete nitro kit!!!

[@jesstreloar7706]

Home decorator vice a builder of homes? I do love the builds.

[@shanecoker8566]

I’d like to know it does running 80-85 mph all day because that’s what speed I’m normally traveling at? I’m a big highway rider and try to travel all I can. I run my old shovel around town.

[@newenglandbiker2220]

Completely stock 2021 114 I have 101 horse and 121 torque

[@ProfessionalMonkey]

That’s a really happy dyno…

[@formdog9861]

sounds mean love the lope nice bike

[@michaelmitchell5909]

What mufflers are those man?. Love the looked of that wide fishtail....looks more like a sharktail

[@williamhelfrich8242]

That bike sounds awesome

[@markscustommasonry]

Great video, can you or anyone tell me what will going with stage 2 on my m8 114 cost me in fuel mileage?

[@ProfessionalMonkey]

I haven't paid attention, but I don't think much? I haven't noticed it...

[@HOOLIGANfilmz]

Great build bro!

[@richardmoorer2668]

Kevin Baxter has a great detailed video on cams

[@freedom6919741]

He built my motor.

[@IndigenousSteed]

That's impressive for what it is. I would be curious what my v124 s&s evo would run as is.

[@brandendoyle8984]

how come the guy is not working whenever u go back there

[@JA-zh5xi]

That is a great sound!

[@RoadGlider1839]

So the 475 is good but what about the gas mileage and tuning? I am sure you would have to get headers too Right? eliminate the catalytics converter and tune it up>

[@ProfessionalMonkey]

The video before this was me doin the head pipe

[@rludwig1000]

HA! I KNEW you had a mechanic hiding somewhere...

[@ProCharged377LX]

Wife’s Lowrider S 117 w/475,Vance & Hines big radius & stage SE 2 tune only made 98.17 hp & 116.66 torque on a Dynojet.Any ideas why low in Hp? Thanks.your bike sounds bad ass brother!!

[@ProfessionalMonkey]

It must be the tune. That tuner is EPA compliant so it won’t allow the bike to run as strong as it can.

[@williamvaughan6448]

I agree...tuner. mine was similar with the SE Tuner (+ wideband)...all changed with the PV 2B tuner!

[@bradleyyounger8499]

Looking great sounds great

[@nikkik6412]

I love the green / Grinch. Did you or will you change the clutch as well? Hubby is going to up his 114 SGS to stage 2, same cam but also a clutch.

[@ProfessionalMonkey]

I should be fine at this level, any further and I would swap it.

[@00002330000]

I have a 107 @ 107hp 122 trq

[@s.gossett5966]

It might sound a bit silly, could you go over the mileage you get after the cam change? Ive been thinking about getting more oomph out of my 107 M8, but it is my long distance hauler so distance per tank still matters to me at least a bit.

[@ProfessionalMonkey]

Its gonna go down, but not more than 2-3 mpg. The bike is finally getting the fuel it needs to run cooler!