Welldone guys Good to see u are working on the old school xf spac 🤙🤙🤙
@kevinhamling19632 жыл бұрын
G'day guys. I've always got a soft spot for the XF. My old XF panel van had done over 760,000 when I sold it back in 2002. Still running the original engine and original auto. I did throw a second hand diff from the wreckers in her at about 600,000 mark. So thanks for sharing. MILKY
@KUSHDFIFA2 жыл бұрын
barra the world!
@shaunhinton36912 жыл бұрын
Sould be a bleed screw on thermostat housing and run the heater also 🤙
@gregorygeyer36342 жыл бұрын
That gearbox noise sounds exactly like they did from new. And hoping that’s the last milky we see in the XF. Keep up the good work boys 👍
@danielflack79022 жыл бұрын
I'm pretty sure there was a speedy sleeve for the selector shaft on the XF, there was a speedy sleeve for the rear main, I did lots of them in the early nineties.
@matthewwilson54862 жыл бұрын
Milky. love the xf build was my first car
@rupanyup2 жыл бұрын
Couple of milky comments below too
@bigal8782 жыл бұрын
I’m surprised you didn’t put a drain bung in the auto pan whilst you had it off. Good video
@piffiiiiiiit2 жыл бұрын
That's one fine looking bbq pit. Why doesn't mine look like that?!
@samchristodoulou79942 жыл бұрын
Postman Pat. Postman Pat. Postman Pat and his black and white cat. ☺️
@lachlanwoods39402 жыл бұрын
Do do do do do do, do do do do do!!!! 😂😂😂
@dazaspc2 жыл бұрын
It's a head sadly. They were a bugger to get all the air out. They used to have a bleed nipple on the thermostat housing to get the air out. Even with the big funnel on the radiator if you don't use the bleeder it will have air in it. It was a big reason why they had problems with the heads. It would be worth fixing though, weld up the corrosion and face. Did you put in another circlip? Usually on the selector shaft.
@genekay82662 жыл бұрын
I only watch these videos for Nathan's laugh
@baidenbehlwhyman76612 жыл бұрын
Hey boys, I’d love for you guys to make a milky white window banner I could put on my bravo. You guys are the reason I decided to have a crack and start buying the bits to put a turbo on my Ute 🤟🏻
@jasontaylor78372 жыл бұрын
Clutch fan nut is 32mm you should be able to get the fan spanner from burson
@harrisonmunro9430 Жыл бұрын
Hey mate, I’m about to do this for my Xf is the nut on the front of the fan behind the raidiator. Or is it the one behind the fan near the belts.
@jamesmoonie54172 жыл бұрын
Trying to find an XF or XD myself, that needs a little work, few and far between at the moment
@FuManchu5ltr2 жыл бұрын
Cool graphics.
@peterspozetta94452 жыл бұрын
Owned several xf falcons in my 20s never got the milky problem but host of other issues, I repaired my center console with screws and washers to make it solid again.
@odinxf2 жыл бұрын
Lmao mines got a peice of wood underneath, i have a good console aside though
@pauls35852 жыл бұрын
🤣Nice and milky boys.
@RocketsFishingAdventures2 жыл бұрын
The milky bars are on you!
@shaunhinton36912 жыл бұрын
Yeah pretty sure it’s left hand threaded 🤟
@MrSamlyle2 жыл бұрын
Spark plugs?
@leithalchin2 жыл бұрын
MILKY XF ESPRESSO
@reecebaker49822 жыл бұрын
Best part of land of the lost when he touches that monolith thingo 😂😂
@jakeyy_wakeyy76822 жыл бұрын
My old xf ute used to go milky with the oil when I would degrease the engine bay and hose etc, The tappet covers on them loosen over time
@james229392 жыл бұрын
Half hour of automobile godness
@brentcouper15132 жыл бұрын
Milky Xf Nespresso
@jamesbaylis94382 жыл бұрын
Sometimes, it can be boring work that needs to be done, but the Shenanigan's are always fresh. 😜
@deets_2 жыл бұрын
What was the circlip in the trans pan? did you work that out?
@GTRRACING3932 жыл бұрын
Milky.... Turbo the crossflow?
@rjpheonix672 жыл бұрын
Milky. Never had that happen to my XF.
@Ben-bj3ev2 жыл бұрын
Barra
@cdh762 жыл бұрын
Milky lol. Just condensation from sitting perhaps?
@g_wizard98662 жыл бұрын
*something Something* milkshakes to the yard....
@JAStheACE2 жыл бұрын
Just another comment, I wouldn't put extractors on, fit a new healthy exhaust to the stock manifold (if it's in good nick) and leave it at that. There is no gain and only pain doing that on such an old setup. If in future you decide to hop it up, the exhaust can be tapped into easily. BTW extractors never seem to fit properly through those models and causes more problems than needed. My two bobs worth. Keep up the good work fella's.
@peterspozetta94452 жыл бұрын
I put extractors on my xf years ago with no issues at all.
@JAStheACE2 жыл бұрын
@@peterspozetta9445 you must have got lucky then, the few XD XE's I've done there always seems to be an issue and i think the sound is deeper with cast manifolds.
@peterspozetta94452 жыл бұрын
From memory I used high temp silicone for the gasket, followed a older mechanics advice lol
@eltonvanoorschot20212 жыл бұрын
turbo green top barra/btr
@gazza1162 жыл бұрын
someone should have told to spin the fan off first,left hand thread just a sharp hit on the spanner and off it comes.
@myxrutefalcon2692 жыл бұрын
Those borg type 35 box's have a pissweek reverse parts in them .
@Frontman9362 жыл бұрын
Correct, my old man gave up on his over 20 years ago when reverse went.
@andyjames20822 жыл бұрын
Nathan, you didn't clean the diff cover? My OCD is aching 🥺
@timwhalan64172 жыл бұрын
👏🍺👍🏻
@nathanzanker22342 жыл бұрын
find a spanner to unscrew fan from water pump
@harrisonmunro9430 Жыл бұрын
Do you just put the spanner on and spin the fan to remove it ?
@mattcrick21562 жыл бұрын
Hahahahahaha
@Cchange4us2 жыл бұрын
Om606 swap it ;)
@timsorensen20852 жыл бұрын
Info the big 32 mm nut on the fan it’s left hand tread easy as
@williamhasty24052 жыл бұрын
milky
@colmastro43732 жыл бұрын
These guys a way too possitive and happy about a bad oil leak lol. I'm riddled with frustration and and anxiety when i cop on. I mean, i have a very slight rear main leak and i feel like throwing the car away lol.
@Shanes_Shed2 жыл бұрын
No sump plugs on trans pans annoys the shit out of me too
@grimreaper61122 жыл бұрын
you can always braze weld or weld one on there give you something to do.
@rockbiterhd2 жыл бұрын
How many times have you ever used the old fan belts in the car I don’t know anyone who has the belts are new
@odinxf2 жыл бұрын
Please dont barra swap whatever you do, either leave stock or build an awake crossflow. Barra swaps are so generic in xfs.
@Xfalcondan2 жыл бұрын
Fully agree, barra swaps are boring
@mex3512 жыл бұрын
Can't agree more. Still own 2 xflow XF's and love the vibe. Not fast...well 1 of em is but the sedan is total go slow mode only. Really were meant to be a Taxi.
@treybaxter180 Жыл бұрын
Take the motor out to put in a new V8 engine into it
@thewraith63602 жыл бұрын
Shes begging for a barra green top
@gixgix4572 жыл бұрын
There were hackers trying to get me after my last comment on your last video. Just to let you know. Wanted me to download something.
@adamheazlett11792 жыл бұрын
XF injected really would get up and go Eat crossflows with work .Remember TE Cortina webers half cage looked great $1000 XF always beat it.80 kmh light em up
@mex3512 жыл бұрын
Bahahahahahahahaha. A NA xflow smoking tyres @80kph is a lie and you know it. Ever owned a car that can smoke the tyres @ 80KPH? Stock NA xflow is not on that list.
@lachlanwoods39402 жыл бұрын
Ummmmmmm, both my carby XF’s were far better than the 2 injected ones I’ve also owned. Stock, N/A injected motors were rubbish, not a chance it was lighting anything at 80kph, barely making it to the 80 flat to the floor!!!!! 😂😂😂😂😂