Getting your toyota to run with a used or new pcm. Vin rewrite with autel scanner. Immobilizer reset

[@MikeSmith183]

it is good of you to post this video, I am in this position at this moment and have an autistic granddaughter who cannot handle change this is a GOD SEND!!! My hat is off to you sir and the world could stand many more of people like you HAPPY TRAILS WHERE EVER THEY LEAD YOU !!!

[@8power0]

SORRY JACK I ACTUALLY FALL ASLEEP BEFORE YOU POSTED THIS VIDEO , BUT WHEN I AWAKE I IMMEDIATELY POSTED THIS THANK YOU . YOUR CHANNEL IS ONE OF THE BEST OUT HERE I CAN'T HELP BUT KEEP SAYING AND THANK YOU SO MUCH . VIDEOS LIKE THIS ARE HELPING MORE THAN YOU KNOW . IT'S HARD WHEN YOUR TRYING SOMETHING NEW AND YOU HAVE NO ONE THERE TO ASK OR GET ADVICE - GUIDANCE FROM ALL THE BEST .

[@danielpeterson2843]

Well. After ordering an ecu from fs1. My 06 sequoia wouldn't start. Just crank and crank. I was irritated and started doing research and found this video. Thank you so much!!!!!!!!

[@AaronLeach5]

I used this on a 2006 Toyota Corolla s. I was having weird codes on a previous ecu about throttle body. Changed it same issues. Changed ecu, was getting crank but no start. After using this technique I’m getting the start. Preciate it so much!

[@rickpontificates3406]

The reason for the failure after VIN write is likely because of the slow write times of FLASH memory. The scanner is not waiting long enough after writing before reading to verify. As an engineer, I see this in flash memories all too often. A software tweak to the scanner tool to add a delay before reading would solve the problem.

[@laurenceleeroceta8772]

Hi sir Jack.... I feel great to see you videos again... I really miss your videos. Welcome back sir. Keep safe always.

[@gilbarcomv1]

Excellent video and explanation... Questions...Step 1...Disconnect battery...Step 2: Remove old ECU...Step 3..Install and connect the other ECU (new or other)...Step 3: Connect battery....Step 4..Jump 4 & 13 terminals...Step 5 ...Key on for 30 min or more...and must see lights blinking on dash... Step 6...Remove jumper wire...Step 7...Start Engine... And after engine starts...the VIN can be done? Or in other step? Thanks!

[@derekdlick2516]

Hell yeah good video. My autel scanner actually said the vin rewrite was successful. I re-read it. It's good. Thanks. Now for the test drive.

[@ahmedmansour8993]

What autel you using what model

[@russochino]

New 2024 lexus RX, does not have 13 pin, any idea what is the jumper formula in that case?

[@billyyoder8171]

Thank you Jack. Good job. Merry Christmas to you and your family. Have a blessed and safe New Year.

[@chestnut1823]

Either way you hold it top side up or top side down: the top row of pins is 4th pin from left bottom row 4th pin from right

[@onebad66chevelle44]

Thanks man great info . Dont do many keys anymore . But when u have a pain Camry this helps . Almost like a Nissan . Should have it where shops like us get a monthly bulletin in key programming when u are constantly doing electrical diag shorts misfires hacked harnesses jumped backwards cars lighting strikes

[@NeuroDivergentRabbitHole]

Is there something maybe a little more affordable to a home mechanic than an autel 906 that can at least do the VIN re-write? I may need to replace my ECM, and I will definitely need to be able to pass emissions afterward.

[@miqbal1981]

Bro I love you... And May Allah reward you his best for sharing your knowledge...

[@Skygazer-7]

My 2004 Camry will not accelerate. I suspect the throttle body but also when I hook up my scan to the only thing it will read is the temperature and O2 sensor voltage. It will not identify the car or read any codes. Do you think this is my ECM going bad?

[@zanetom1967]

I have a question to ask you or anyone reading this comment. I have a 2007 Toyota Corolla. I lost the key so I had a couple people come out to cut a key and reprogram the key. One person said the 'immobilizer amplifier' was broken and that's why they could not reprogram the key. A few days passed and I found the original key however it would not start the car because the old key was erased from the computer and the car was in program mode with the security light on. I bought a new key, ignition, immobilizer amplifier, ECU all from the same make and model and all from the same car so they were already merried together. When I put the parts in my car it would turn over but not fire up. The car was running perfectly fine before I lost the key. Any ideas on how to fix this or what I can do to finally get the car started ?

[@carverautopsy2898]

Hi Jack, great video hoping you can advise. I've acquired a 2010 Corolla key less entry. It has been vandalized. Lock and keys gone, ignition switch gone. Damage to steering shaft. If I could get an entire suite of parts from a single salvage vehicle including door, glove box and trunk locks, full steering column with a working key and maybe even the PCM, would installing all these parts get me a working and starting car? Would it need any computer programming to get the car started? I'm in Canada. The locksmiths here are giving me mixed signals.

[@hesbonazablon1611]

I am also kind of in the same situation. Got my keys stolen. I have bought a used immobilizer/ignition unit with programmed keys that hopefully I can install then do the "handshake" as he describes. I really hope it works.

[@miekolock4060]

Yes you would need the immobilizer ring from the car your getting the keys from

[@bundylovess]

Nice video mate big thumbs up and thank you for sharing you knowledge big thumbs up 👍

[@blkshk1]

Garage having fun w my 2001 Sienna xlt. Think they found TCM software to take off internet FINALLY!

[@GreatKhmerEmpire94]

What model autel scanner did you use? I have a mk808 autel i would liketo know if my svanner can reprogram the computer.

[@tahotoy]

Jack ! If you're still reading these, great video. I may need to swap an 01 solara ecu with an ebay special. I'd like to avoid the SMD time on board. My main concern is shorting those legs and causing a new problem on an older car. Some quick advice would be very appreciated. Thanks !

[@dougbrown6626]

For the love, can someone tell me what to do if I don’t have a wire in the 13th port? 2020 Camry LE, won’t work like this!

[@555666jyd]

Did you ever find out witch one it was

[@blkshk1]

So when u speak about changing the vin do you mean add the vin from the replacement tcm mod?

[@meassavuth4649]

Hello sir is this way can run with other used or new ECU ? And what kind of your Scanner for reinstalling the program to the ECU ? , thanks

[@arthurfricchione8119]

Jack, another very informative video. I own a launch diagun4. Can rewrite vin I believe I’ll check to make sure but on Honda’s are there pins to jump on the DLC connector to reprogram the immobilizer. Thanks again. Artie 👍👍👍👍

[@EdgarMikhail]

Hi Jack, Are still doing SMG to manual conversation?

[@ibrahan7680]

Thanks for your video. And i understand with this way the car will start every time with keys even without chip programmed ?

[@duanedonaldson2262]

If the connector is upside down, the pinholes will still be in the same location, same orientation, no worries.

[@fireyourrocketts]

If I replace mine on a 2004 Toyota Corolla CE, Manual 5 sp, do I need to do this? my car does not have the power pack, it is basic model ECM would be used it comes from a 2004 Corolla but with AT, my scan tool is actually the XTool D8BT, some say I do not need programming of a different ECM and the scan tools shows "not supported"

[@imimran3277]

So ! there is no need to get the ECU Flashed/reprogrammed ? and a good working used ecu from another car with matching numbers can be put to use by this process of jumper wire , eliminating Flashing ?

[@luisrayon553]

hi Jack, I lost all keys but I did have a copy no programmed so the car no star! this key will star the 2003 Toyota Sequoia when I reset the Immobilizer? thank you for your videos

[@Makal.0w0]

Would I have to “virginize” the ecu or does the scanner delete the old vin?

[@robtemple3445]

Thanks Jack !

[@douggregory2922]

Jack I am a locksmith and was curious if I use my MVP Pro and do an immobilizer reset will the car start without jumping the pins?

[@markferraro5250]

Wow thanks Jack. Great info

[@taiwoadegbite2209]

Hello , I do have 2015 Mazda 3 Sedan that the engine did not want to start , please can you let me know what Pin number to jump . Thank you for good sharing knowledge.

[@ChrispyTofoo]

I did the jumper to reset my ECU 2000 4rummer 5vz- no dash lights blinked. According to Ai, this should have removed the need for a Master key for programming new blank keys in Techstream, v12 . didnt work. My immobilizer is activated, from before any tried hacks, my slave key will nit start engine anymore. Just trying to get ECU to reset. Battery unconnect did not work paper clip did not work. Any Ideas??

[@Rudy-wc4cr]

I bought a 2017 Toyota Tacoma from the auction and it was a theft recovery, so there was many parts missing including the ECU immobilizer and of course no key fob, it is a push start with the smart key, so I ordered a used ECU from eBay and I got the immobilizer module and from a local wrecking yard and a smart key fob from a body of mine. Now I installed the ECU the immobilizer and got the key fob present, I followed the steps jumping the pins on the OBII I tried to started and it just cracking but it won't start, I jumped it few more times and is the same problem no start, I even barrow an ANCEl-X6 from a friend and i just can't get it to run. So if there any chance that you can give me a hand with it? I would appreciate it if you do thanks and have a great day

[@mrbmd710]

Did you get it to start?

[@momcarr8813]

Greetings! Not sure if you can help, I have Toyota sequoia manufactured 11/03 that a locksmith flashed the module behind the dash but he can't get the keys to program. Do we have to use a paper clip, and is there a key procedure before the paper clip procedure? Anyways hope you can help? Blessings 🙋‍♀️

[@lexicorp69]

I got the same problem this procedure won't work in sequoia 02 if you can help please let us know thanks

[@deadonarrivalparanormal981]

Will it work for a toyota camry se 6 cylinder and will everything else key locks work?

[@chrishayes2009]

Which AUTEL are you using for this Video ?

[@ADDAUTOMOBILESERVICES]

Ms906bt

[@ManySan-o3q]

Hello servirá este procedimiento para una Toyota avanza?

[@fredabounader9165]

Will this procedure work with a salvage yard ECM for 2016 Toyota Highlander?

[@tylorhotard4368]

I know this post is old but i have a 92 4afe swapped into an 87’ corolla i need to power the ecu to stand alone , an hardwired due to my factory harness having none of these things. I have the 92’ computer and dont know how to hardwire it. Can you help?

[@phillipanglin4781]

What computer are you using?

[@charlesmecum5009]

How about 14 hyundai santa fe used pcm says vin already changed, but has old vin from wrecked car stored in it.

[@danielsalefski2046]

I have a 2013 es300h. I installed a factory remote starter and followed the manufacturer instructions. the start stop button 5 times and the flashers should blink one time . this procedure has failed... I have a scan tool that sees the remote starter and I get a code in history and current for no communication with the remote starter. any ideas is this issue related to the vin not matching in the 2 devices?

[@mikep47]

I have a 2013 Corolla s. I just got a used ecu and swapped it in. Car starts but immediately dies like it’s not getting fuel . Was told it didn’t need flashed or anything any help would be appreciated

[@JoseGarcia-px9xj]

I have the original fob for my 2010 prius(working right), but it is not recognized by the car. So I cannot start the car, any suggestion

[@JonathanLyde]

Hey Jack great informative KZbin channel you have. I was wondering do you program MB keys and remotes with transponders ? I'm not sure where your business is located or your range of travel to service vehicles but I have a 97 MB SL320 and I lost my remotes and my spare master key I have wont marry to the immobilizer to crank up my car it turns over but wont start I'd like to become your newest client to resolve this issue can you help ?

[@Greatglenway]

Can I programme a second key on a aygo without losing code for original key

[@MobilemechanicPhiladelphia]

I had Corolla with non communication code will I need to replace PCM or is there a place to reprogram PCM 2015 Toyota Corolla

[@israelsalvador3792]

Didn't work on my rx350 07 Lexus I even change the vin to the car original vin still won't start do u know why or it doesn't work for my vehicle

[@jamesgarvey8279]

Thanks for this!!!

[@user-no8bv6xt8o]

Thanks great information

[@MustangFourSix]

I have a autel maxicom 808 can I write vin on used pcm for a 2005 chrysler 300c?

[@edvega4481]

Flipped over its still in the right spot 13 and 4

[@xavierdelgado1023]

On a 99-04 mustang can i find a junkyard car and swap cluster .key ignition .pcm .and put those parts into my car will it start .is there anything i need to know..trying to get this car on the road...i have a junk vehicle i can use same car same year 4.6

[@tommymutz9197]

What software are you using

[@xavierdelgado1023]

Will this work on a 99-04 ford mustang. Swaping pcm cluster key ..will it work

[@t-series293]

Sir jack. Will it Works on Corrola 2014 Chip H immobilizer ??

[@aminsab8893]

This method work for International Toyota or just Usa Toyota ?? Thank you

[@jackmeyers2911]

Honestly i'm not sure. I would assume they have the same procedure worldwide.

[@aminsab8893]

@@jackmeyers2911 Thank you

[@user-2uf2kr2c]

Hi nice video, thx. I saw another video where the jumper pin was put in first before the ignition was switched on, and it worked also. I guess it doesn't matter which is done first then? Regards

[@dtnel]

Are you a locksmith? Just curious. If so what's it take and how much to get the stuff needed (paperwork) to be able to write it. Also if you have a J-Box like the Drew Tech 2 or 3 I think it is and go thru the mfr site can you do it that way? I'm sure there's a fee for that is my guess? Also I should check my Zeus scan tool as I'm always learning with it each time I pick it up. Wish I was picking it up daily at least a few times a day as I'd definitely retain more that way.

[@jackmeyers2911]

Yes I am. You have to register through the nastf. Its kind of a mess right now because they are going through a migration to the sdrm . You need to have a business license both local and state, if required like here in california, insurance with them specifically listed on your policy, a background check, professional references ( they do actually call everyone). I can't remember anything else off the top of my head. It does take about 6 weeks to get it. I use a drew jbox but really prefer a vci. My bosch mastertech is my daily programmer. You can get pincodes from the oems through their website or the nastf but you must have your lsid attatchedt to your login when registering with most of them. If not they block you from security access and only let you program. There are ways to work around getting pins strictly from oems and most of us use the ones that work. Getting securty codes from oem websites or token systems come with a high price and definitely cut into profits. Honestly, With all the cost behind becoming a locksmith (tools, insurance, key stock, etc.) It's very difficult to make a living doing keys only. I do a quite a bit but make more programming , repairing modules, diagnostics and wiring repairs.

[@Hamdhan777]

Can confirm this works on Toyota Yaris mk2

[@earlyt766]

My 1997 toyota has onl 4 wires. Power grounds and ecu.> What then?

[@tombstone2826]

Will this work on a 1999 toyota 4runner ?

[@giorgiispirov7129]

Hello friend, this option works for the old years! How to sync ECM on Camry 2019?

[@scratchgang8391]

Did u figure it out

[@trini_boi2414]

This work for me but now I don't have no power coming off the odb socket maybe it's a blown fuse..

[@diydantex6150]

Thank you

[@kenshinhimura-01]

Toyota ECU eprom chip 93C56, Can it be replaced with any 93C56 chip from any manufacture?

[@toheebabdulazeez3001]

Pls were is the cable located

[@toheebabdulazeez3001]

Pls were is the cable located

[@cassimoolmanmoolman7785]

hi i have a toyota hilux kzte 3.0 diesel lost the key coding and do not have master key what can i do

[@senorkey-um8mf]

Thanks

[@somphonesaiyasone4738]

will this work on a 2012 toyota prius

[@raymundovasquez6381]

Will this work on 2001 Lexus Ls430?

[@studioti]

Will this work on 2016 Toyota vehicles ?

[@jackmeyers2911]

I'll have to look it up and get back to you on that.

[@johnhurley2457]

Will that work on a Ford explorer 2000 model and you tell me what the pins I need on that

[@ThEmEsSiAh187-CFGeorge]

No. Ford is different. You’ll need to program the VIN into the used PCM. The programmer will also do a key reset which will either require 2 keys or just one if it’s a parameter reset. You can program the keys only, but you’ll get VIN mismatch codes.

[@meassavuth4649]

❤

[@jeanetteheitmann4232]

I changed out my battery on a 06 Toyota Camry. And now it won't start the anti-theft system is engaged. Many years ago there was a process by which you pushed the button on the remote so many times went 30 ft away from the car waited so long did some other thing and it started can you help me please

[@markvermeulen1372]

Pokemon cheat codes generation. Mankind has achieved the age of mass chaos.

[@tedslife7086]

What about a 2004 lexus RX 330

[@ismailorahovac1732]

Do you know how to correct the miles on the cluster?

[@ismailorahovac1732]

2014 Ford Fusion I replaced the cluster but the pcm Ecu are all original with 16,000 miles but the cluster shows 57,000 miles, is there anyway I can get it corrected?

[@jonjon-nc5br]

paspeedo.com

[@tommymutz9197]

I have a 2010 Venza. I’ve tried to do this and nothing happens. I’m at my wits end with this. I can’t for the life of me figure out what is going on. I think I need my computer reflashed

[@kenjohn1204]

Which Autel scanner are you using?

[@shawneeguyman79]

That's cool so I don't have to take my used ECM for my 06 Corolla and have it flashed and all that. I can do do that

[@blkshk1]

JACK NEED SOMEWHERE WHO CAN DO SOFTWARE ON MY 2001 SIENNA XLT TCM USED UNIT. WELL RECOMMENDED SHOP TOLD ME MINE IS BAD. HELP I WANT MY SIENNA UP AND RUNNING.

[@chrishayes2009]

906 - hello

[@179joshua]

2003 Toyota Corolla hatchback not working tryed 3 times

[@smoothoperatr49]

Would this procedure work on a Subaru if so are the pins the same?Thanks

[@ADDAUTOMOBILESERVICES]

Yes it will work on it try it

[@theahch]

Can you do this through a breakout box?

[@sundeepsinghbains9254]

Hi , i m having problems with 2008 camry ECM and buying aftermarket ECM to put in my car . My car has remote key and push start will it effect the working of that and is there any process to program key to new ECm working something like that. If u still runs this channel please help me out. Thank you

[@LekarzRodzynku]

Does this also reset the remote key fob? Does this work with 2010 Sequoia? Thanks.

[@andresespinosa6910]

Does this work on a 2018 Camry?