V8 Drift Truck Gets an Upgraded Radiator & Clutch!

[@Seanbee04]

Get👏a👏bench👏vice👏

[@polobunny]

And safety goggles.

[@julianos4675]

This is my favourite drift build on KZbin. Can’t wait till u burn some rubber.

[@RicardoPCGamer]

Burn rubberium

[@rajivsingh1999]

Driftium

[@steorra15]

Oversteerium

[@JHX77]

Slideium

[@destin6041]

You know the a bench vise is like 40 bucks right? I cringe every time I see you screwing around with those clamps lol

[@Kristo99]

yeah and he is also ruining the table he built

[@hogdog567]

Maybe we could start a go fund me.

[@destin6041]

Sergeant Bosco for 40 dollars?

[@xversed5544]

patreon m8

[@chasesgarage4932]

oskarpukk1 I’ve got a homemade bench too, I also have a heavy duty bench vice, no problems for 4 years

[@leonjohansson8469]

9:56 lmao, find any gold?

[@Kristo99]

Leon Johansson haha

[@shiftymiata]

Hey, we all do it man 😂

[@sirgwaine2695]

Yeah, digging to China :D

[@marcoepifani2475]

LOOOOOOOOL

[@sergeantspeed5941]

Fuck I came here just to make that comment lol

[@legomaniac225]

I can't wait to watch today's episode of "Caleb actively avoids buying a bench vice" seriously, it's getting kind of ridiculous at this point.

[@Kristo99]

Willsohn I agree

[@legomaniac225]

The boy is nothing if not resourceful, I'll give him that much.

[@alexmorton9600]

Start a gofundme to get gingium a bench vice

[@christianpierre-louis198]

www.gofundme.com/the-gingium-bench-vice-fund&rcid=r01-153514574969-6f15410b6209447a&pc=ot_co_campmgmt_m

[@alexmorton9600]

Christian Pierre-Louis YES!

[@vf555fotia7]

For the last damn time by a vise

[@Kristo99]

Vince Fotia I agree 100%

[@christianpierre-louis198]

www.gofundme.com/the-gingium-bench-vice-fund&rcid=r01-153514574969-6f15410b6209447a&pc=ot_co_campmgmt_m

[@MrLokojorge]

Hahaha... 9:56, Gingium digging for gold!!! Looking for extra money for the build, nice!

[@Metalcop5150]

Put a small section of fuel line, split down the middle, over that sharp edge, around the radiator cap. I also like to use a bit of gasket adhesive to make the fuel line stick. It will make a nice bit of edging, protecting you from that sharp edge, and provide a much cleaner, finished appearance.

[@666akuma5]

Paint the grille with gloss black and make a red mazda logo

[@Official_OGBANDZ]

that would be beautiful

[@jameshavenga4998]

Gonna be real with you chief, putting a red anything in the middle of a black grill makes it look silly, like as if it has a clown nose. There's a truck around where I live with an all red Ford badge and it just looks so silly

[@dustyarnold2228]

James Havenga same in my town, truck ricers 😂😂

[@TheRealBleach1000]

I like how Gingium doesn't stop making videos even though he had wrong parts for the transmission. KEEP IT UP!

[@Jaszczur-sp2tx]

Get a vise already jesus christ

[@lovelyxyz]

buy him one 🤔

[@christianpierre-louis198]

www.gofundme.com/the-gingium-bench-vice-fund&rcid=r01-153514574969-6f15410b6209447a&pc=ot_co_campmgmt_m

[@redsquirrelftw]

lmao

[@MetrohMan]

Its so annoying now... that fucking grinder being used to cut everything is just cringe worthy too.

[@redsquirrelftw]

The grinder is forgivable, that's what built this channel. lol.

[@indocraptor2662]

U know what would be a good idea what if u put one of those cool trophy truck spare tire roll cage thing on it so of u pop a tire when drifting u can fix it

[@215nerf]

Yeah that might be cool

[@shiftymiata]

And he needs more weight in the rear, that'd be perfect 👌

[@BedSheetzy]

when drifting you usually keep your extra sets on your rig you dont fix your flats on track but great idea

[@Iagopinheiro2206]

Plz stop the video at 10:00 exactly, and tell me I’m not the only one who noticed him picking his nose lmfao I love this dude so genuine, keep on building this rad ass projects and pick that nose away son ! Lol

[@teme1303]

Can't wait to see you drifting the truck, good work!

[@Kyle-nz9wl]

9:57 gingium picks his nose

[@johnsmltz217]

Everyone does trust me

[@mottorcycle2559]

John S I don’t think everyone picks gingiums nose. Lol

[@johnsmltz217]

@@mottorcycle2559 Really? I do. He pays me for it in air fresheners.

[@blakehinerman2557]

Boi let the mans live

[@mottorcycle2559]

John S probably a business opportunity, don’t miss out 🤫&😊

[@lloydy___8720]

Spray those turbo looking things on the end of the camshaft in the grey u used for the camshaft covers and heat wrap the clutch line to keep it neat

[@andthenwut]

Cant wait to see this finished. Then you can do things like brake fluid shield, fuel cell, roll cage, etc. Basically all the really fun drift stuff

[@philiptempleman9269]

You need to plate around radiator filler cap to add strength back into top rid

[@lucashenderson5050]

I'm watching this while a hurricane is about to hit lol

[@kaizen7.62]

Stay safe man

[@TopSecretR35]

01:49 "Tight but it will definitely fit" -Gingium 2018 LOL

[@chadpriceplayz9856]

gingium been waiting so long for your new video are you trying to torture me making me wait for the videos to come out. LOL! love ur vids keep up the good work.

[@kory_4.7l3]

I love how this truck transforms every video can’t wait for it to run!!

[@eddiemoebes9736]

9:56 trying to find a bench vice in his nose lol

[@centurybug]

Still amazed at how fast this project has gone when it's been pretty much only you working on it. It took me like a week just to sand and repaint my headlights.

[@dr.roundbottom31]

Gingium you have such a good community, a youtuber is considered "relevant" when they get 10% views to subscribers per video, and you get around 20-30% views to subscribers per video, jus wanted to try and motivate you cause you really inspired me to buy a miata and now im prepping it for autocross, thanks my guy

[@LoneRevD]

Once you get that cap hole hogged to the right size, you might want to take a piece of vacuum hose, split it and then put it over that sharp edge, your fingers will thank you... Fits in there great, tucked in tight.

[@Deluxe00exe]

KEEP UP THE GOOD WORK GING! I LOVE YOUR VIDEOS! DON'T LET ANYONE GET YOU DOWN! I'M LOVING THIS BUILD!

[@turboboy0]

Please use a hole saw and dimple die the front bumper to remove some excess weight and allow more air to flow to the radiator for better cooling.

[@FastNBulbous]

9:56- caught you picking!

[@-sargntclashroyaleandmore-491]

Rear mount the radiator like they do in formula drift... works so that if you have a front collision you won't puncture the radiator etc... also a rear battery box and fuel tank will help not only to have better access but to add some weight to the rear so that the V8 doesn't make the truck unbalanced at the front 👍🏻

[@quancast1141]

I don’t ever get excited about videos but ging is just awesome

[@Angel-co9yx]

9:55 mining for gold 😂😂

[@nicovanduin1553]

"How to build a drift truck without a bench vise"

[@nelsonramos2218]

By far, the best mini truck proyect in youtube ! 1uzfe are so awesome! 👍

[@jhuba6477]

Can't wait for the first start up.

[@baloneyjusticecheezedog]

You know.. I can't believe this truck will be running soon. Its insane you basically, (and by yourself no less...) shoved a V8, new transmission, and redid the entire suspension on it. It is pretty gosh darn insane to think about.

[@finjmaple0571]

Wish could travel into the future and see this project finished 😂

[@DMorgan24]

I can’t believe it’s almost done I can’t wait to see it start up!

[@bladerunner757]

B E N C H V I S E

[@milkshakethick5765]

Beardgium casually picking nose at 9:58 xD

[@flamax5742]

Mazda itself would be proud of this build

[@guni7197]

*_Can't wait to see it done, and also hear it! Love your videos Gingium, and i like the progress!_*

[@rntjake]

GETTING CLOSER BIT BY BIT

[@LemonMan_Man]

For using a hole saw, treat it like a saw slow and steady keeps the blade way longer. Use a real cutting oil too wd40 is a powder once it drys not very good for lubricating. Also buy a vice

[@OutOfLineGarage]

Make the fans pusher instead if pullers. Looks like you should have enough room up front for those. Maybe make a fan shroud?

[@alebone_]

Pushers are less efficient, they block air from entering the radiator

[@OutOfLineGarage]

If it comes to him needing room though they will work. I had pushers on my turbocharged mustang at one point and they worked just fine.

[@roarore8810]

[Out of Line Garage] But he doesnt nees more room, therefore fans that pull are better in his situation.

[@crownedrc652]

Thank you for clearing up the flywheel bolt concern. Just didn’t want to see anything bad happen.

[@kingjimmy4770]

9:56 did you find anything good 🙄🤔💀😂🤣

[@rafee9442]

Yeah, he stuck gold.

[@kingjimmy4770]

@@rafee9442 😂😂😂

[@zachbutler9137]

Hey Caleb! My name is Zach, and I just want to say I’ve been watching your videos for about a week now and let me just say you have inspired me! I’ve always wanted to have a project car but never thought I could really be a welder or a fabricator. You have shown me it is possible and now I can’t wait to get my on project car! (Maybe a Miata..) just wanted to say thanks! And keep up the good work!!

[@dawsonhall4670]

10:57 "these aaaare" I laughed way to hard, it was just how he said it lol.

[@cq1311]

This is awesome. He came from bot knowing how to put coilovers on a Miata to building an entire car. What an inprovement.

[@j.hyatt2776]

This is the build that makes Gingium a truck guy from now on.

[@MetalheadEchidna]

using the hood latch location for the radiator cap is absolutely ingenious.

[@banzai.drifto]

No one may say it but I appreciate the clean shop bro! Clean shop, clear head, best work.

[@WTFtrollsFTW]

do holes to your front bumper for the better cooling and it will also look awesome :)

[@slowaccord]

Bro i'm getting so hyped for this thing to come together! You've been working so hard and you're getting better with this fabium work every day! So proud of you! You're video quality is improving greatly aswell :)

[@tomparker3654]

So far so good we're almost there!

[@troubledsouls574]

You should paint the Mazda letters the same color as the valve covers to match.

[@FunBucketHd]

Hey, drill the whole be for cutting the pieces off of the steel. That way you have the whole piece of stock to clamp

[@nickrr3626]

Lol who was waiting for him to say he ordered the wrong part 😂

[@colscoffee8013]

Love the quality of your work and you're videos inspire me.

[@elementmaniac]

This build is so good.... Love it!

[@CarsOverdose]

You should definitely go with the no-bumper look. It'll be sick

[@nicolastaylor7470]

#notificationsquad where you at???

[@RantzCore]

Driftium Truck is really coming together! Great work Caleb! I bet you didn't see yourself doing this a few years ago. Looking forward to your next video!

[@MrGokufan96]

9:56 I hope you got a good one.

[@justinrabideau7042]

i love watching your progress when i started watching your vids you had fred with just aftermarket wheels just 3 short years later you have a fully built track car a rally car and a drift truck almost done you started with humble beginning and i have watched you grow not ony as a youtuber but as a mechanic i am currently in training to become a master mechanic and i love watching other go through the same thing i always look foward to your videos and i miss fred and your old toyota camry but these new cars like molly are alot nicer

[@rickymarquez4628]

I’m in class rn watching this video cause Gingium is more important

[@zanehopefz6hundred761]

Ricky Marquez stay in school shit head

[@validpostrz]

Gingium is more important

[@cq1311]

Zane Hope FZ6 Hundred How about you are a shithead Fucker

[@kennyhuynh9688]

@@zanehopefz6hundred761 he is in school, technically...

[@zanehopefz6hundred761]

Ricky Marquez haha! Jeez.

[@benmoore7721]

Think about some “speed holes” in the heavy metal front bumper. Better airflow for that radiator.

[@fardinm8196]

BOI! It’s coming along nicely!

[@carterzurla1368]

you should cut out the little hexagons in the grill and either replace it with black mesh or leave it open i think that wold really add to the look

[@lsswappedcessna]

Might want to, eh, check for bubbles when you get the radiator set up. That ended up being my cooling problem. I watched the mechanic do it (from afar) Thing sucked in what looked like an entire gallon of coolant.

[@e30sheib]

Having a smaller bolt might throw the balance off a little bit, but it’s not a huge deal. Might wanna change it down the line though just for reassurance.

[@going35]

9:56 😂😂 whole finger in his nose

[@banzai.drifto]

All y’all talking about a bench vice but I just want him to put something between the bench and the item he’s drilling. Destroying that table my dude.

[@TrixxEsports]

9:55 So focused on digging

[@danieladam4424]

Can you turbo it in the future? Pls

[@samuesharpdiamondswo]

There is not really enough room. It would be cool tho!

[@hogdog567]

It's SOS there's loads of room!

[@big_ostrich_egg7287]

He is building the other motor for force induction in the future might be for turbos?

[@markas7356]

He can make turbo sticking out of the hood

[@rhissian5260]

7:37 see that knobby thing next to the coolant intake? that is a stock turbo..... so dont say turbo it in the future....you mean upgrade the turbocharger(s) that are already there.

[@jameslings5353]

Just a small suggestion but I really think it would add to the overall look of the car if the Mazda logo on the grill was painted red and maybe black X’s on the headlights. Very very cheap and easy to do

[@SpeenNHinch16]

Now keep it organized!;) truck is coming along nicely buddy! Dont get discouraged... you are doing all the work alone. Cant wait to see it RIP!

[@that_540guy7]

Awesome how fast your build is going! But I would keep the car at that hight maby camber out the wheels in the front a lil but looks good. I raised my BMW for a reason .

[@MaxMarcotics]

Might want to put some washers between the bolt heads and bushing otherwise you'll have dead bushings after some time.

[@trentlewis1473]

Hey Gingium, build is awesome, can I recommend that you put some screen (like you see on a screen door) in front of your radiator. It will help keep objects from damaging the radiator

[@pantsinajar]

Good editing to the music btw. As a person that has a BS degree in videography, this was tasty. Thank you

[@dwolf97]

Dude you have the coolest Mazda pickup on the planet

[@kristianhansen4522]

9:43 you should weld it all the way

[@TimmyTwoTuck]

I can’t wait to see this thing rip!

[@travislazenby6797]

The day gingium gets a proper bench vise will be a great video.

[@BoostDreamer]

Very nice work. It looks amazing

[@justauser]

i would go back over the front suspension and see if theres any way to reenforce it. Better to fix it now before it breaks later down the road

[@Klemhaken]

If you're drilling in steel water the bit and the metal so your bit wont schatter or get dull

[@DUDERZ_]

Cant wait for this to be turbocharged and turned into a drag build

[@ethanallen2326]

You get a like for the sequence of numbers that represent the videos length.

[@_zombie__45]

With your angle grinder just push the button in to lock the blade and grab the blade and unscrew it. No need for that tool unless the blade is worn all the way down.

[@Hauuy-el1vv]

Get a bench vice! I love this build and videos so much!

[@TheTorkerman]

Never seen a KZbinr that gets so much support from cool supliers, at your sub count anyay. Pops to you Mr Gingium.

[@drakeorion94]

You could mount them on the other side of radiator as well

[@jackbaker7346]

That thing would look mint with a big but low scoop on it, td42 Nissan patrol scoop

[@MrDumont686]

Ging is the best supporter of all other KZbinrs always has other KZbinrs gear on

[@nissancruizer]

CALEB WHY U NO GET BENCHVISE!?

[@bernicesands2265]

9:56 picking his Nose-ium

[@jakobd6028]

you can buy spacers that goes between the rear axel and the leafsprings

[@churt1130]

Jakob D lowering blocks. I had them for a long time on a Toyota Pickup but they’re not ideal for racing use. They screw up suspension geometry and cause a weak point in the rear suspension. I would definitely just recommend mono leaf springs and lowering shocks. Or just coilover conversion.