Givi XE135 - Brake light for topcase

[@Jeroony24]

Je hebt gelijk. die blauwe dingen hadden opeens problemen bij mij. Heb je filmpje herbekeken voor een nieuwe instalatie. Bedankt!

[@miguelballesteros8890]

I did this today following these steps. My top case is a Givi V47NNT, and the process is exactly the same. My top case can't have a customized keylock but all the rest was the same. I purchased the E135 brake lights from Givi and the bike plate from a Kawasaki dealer. I had to glue the connector to the plate using a bi-component glue like Andy, otherwise it was likely the connector to move and fail wiring connection between the case and the plate. Thanks a lot Andy for another very helpful video!

[@MotoAndy]

I'm glad everything worked out, I hope this brake light will serve you for a long time, and of course I'm glad I could help. take care😃

[@Moonlight-zp5rj]

I wish to reflectors below the brake light working in the video. Haven’t found any video on it. Amazing job with the installation.

[@karanchoxi1]

That is an awesome job. This video is like a meditation from the regular chaos in India. I wish I had the time that you have.

[@fernanfer4967]

I like the way you explain in this videos, all cristal clear, not such conmon thing on youtube, I have tried to build up an installation for this, didn´t know the givi kit, and eventually got to the same type of installation, but better with the givi kit, so im going to try :).

[@HazardSports]

You have a lot of patience with that connector on the base plate. I would’ve just drilled a hole in the back corner and used an SAE connector. Good job !

[@francoisdussaud1251]

Nice work ✌️ Super video 👌

[@ppwm56]

Your video was a great help!! Thank you! The only thing I did different was instead of glueing the contact at the right height I inserted 2 rubber rings. Let's see if this works in the long run...

[@PAUL-yv2kk]

Quite a complicated installation, but nice result in the end for your hard work. 👍

[@MaverickAus]

Nice job, instead of soldering I use posi tap connectors, they never fail.

[@sawekgoab4083]

Profesjonalna robota panie Jędrek. 😀

[@jaumebeltran524]

Shad case on my versys,, will see if there is something similar. Not sure if it's legal in Spain🚔, will investigate too 👍 thanks a lot for your videos Andy

[@adys6115]

Nice work Andy, well done.

[@RicardoSilva-nz4yp]

Great vidio. Nice job. Tanks for share.

[@DIVA-MC-7]

very nice install ! i'm next !! thank you

[@pitmac9090]

Dobra robota, dzięki za podpowiedź :)

[@reinharddesar5040]

Prima Arbeit, das gleiche instaliere ich an meiner honda St 1300 Pan european

[@Jonte_W]

Nice work, you are verry good mekanic 👍

[@richardlloyd3483]

Hi Andy, Came across your video for the Givi brake light. I am in the process of adding extra tail lights to my Versys 1000GT and i was wondering if you know the part no for the brake light connectors you spliced into (both male and female sides). I intend to fit an extension lead between the male/female connectors rather than splice into the actual connector. I will then run off a lead (from the red wire) for use as an ignition trigger wire for a relay

[@mauriciolillojulio]

thank it was a good presentation, I want to put the same in a Kawa GLR 1400...

[@arianggara8092]

if i don't have such led lamp, what type of led can be used or compatible with it? Thanks before

[@Prez_s]

Pełna zgoda co do jakości kufrów Kawasaki w stosunku to tych firmowanych przez Givi. Mam ten od Kawasaki i ten sam problem co Ty widoczny po zamknięciu kufra w 26:57. Niezależnie od tego jak ustawię zamek, klapa kufra nigdy nie przylega do dolnej części mniej więcej od połowy kufra. Porównywaliśmy to z kolegą, który używa kufra Givi i u niego problem nie występuje. O dzwonieniu na pusto już nawet nie wspominam :)

[@MotoAndy]

Na szczęście nie przeciekają (o dziwo) 🙂

[@shayli05]

Good and clean job!!

[@Momo-Sparco]

Next episode: MotoAndy installing rear fog light 🤣 Great job Andy! 👍

[@MotoAndy]

You almost guessed it, definitely in the back😂

[@robertodolza]

Thank you great tutorial! 👍

[@olivierqueloz8054]

Salut Andy,voilà j ai retrouvé la vidéo👍✌

[@leonringma4609]

Hoe vervang je de Knipperlichten voor en achter voor Led Kawasaki Versys 650 2017 krijg de voeten niet los uit de kappen en waar zit de relet

[@MotoAndy]

Ik rijd Versys 1000, maar je moet de kappen demonteren en van binnenuit zou er een plaat en een schroef moeten zijn die de hele richtingaanwijzer vasthoudt, relay in 650 heb ik geen idee.

[@leonringma4609]

Bedankt voor de info had gehoopt dat het gekund had zonder de kappen te verwijderen

[@dariuszkasinski2547]

There is no need to glue it to be at horizontal level , just put it in a drilled hole and that's it. I did it that way and it works well.

[@MotoAndy]

i tried to do that in my previous versys and it didn't work, the socket was misaligned and very often there was no connection and the light didn't work

[@dmcmillan1968]

Very Nice Work

[@sawekkowal3988]

Świetny filmik

[@bismarck19br70]

Obrigado pelo vídeo, talvez eu não faça pelo preço dessa peça no Brasil, ou pela dificuldade da base Kawasaki.

[@jorgerivas6318]

No has intentado agregar luces a los Maletas laterales?

[@674henk]

Leuke review van topkoffer remlicht montage, alleen het aansluiten op het remlicht van de motor gaat mij niet lukken helaas 😢

[@anders.svensson]

Great tutorial :)

[@nelsoncosta4912]

Good job 👏

[@UdoGeerts]

Top, dank voor de link

[@LRijt]

Zou het makkelijker zijn om de Givi base plate op de Versys te installeren, of past dat niet ?

[@MotoAndy]

givi past niet heeft een andere schroefbevestiging

[@daleleatherbarrow6354]

what is the part number for the light kit

[@MotoAndy]

Givi XE 135

[@daleleatherbarrow6354]

@@MotoAndy thank you

[@dazadorph45]

Looks great but most cars drivers wond see the top box lights . Maybe if in a sub, land rover or discovery, Lorry's driver may see it. Nice work though.

[@leonringma4609]

Waar kan je ze bestellen en wat kosten ze

[@MotoAndy]

www.rad.eu/nl/c/p/37278-givi-v47-stoplichtkit-e135.htm

[@frits10001961]

hioi Andy heb je een linkje waar je hem gekocht heb

[@MotoAndy]

www.rad.eu/nl/c/p/37278-givi-v47-stoplichtkit-e135.htm?gclid=Cj0KCQjwj7CZBhDHARIsAPPWv3c-HZL-RCrkBwF-D8DTlDrDtVVAgMevFKP4wDtcxK_5fnktxDzNLw4aAkVaEALw_wcB%2cCj0KCQjwj7CZBhDHARIsAPPWv3c-HZL-RCrkBwF-D8DTlDrDtVVAgMevFKP4wDtcxK_5fnktxDzNLw4aAkVaEALw_wcB&TradeTracker-NL&Affiliate&

[@frits10001961]

@@MotoAndy thanks

[@guillaumelemaire9027]

The FIRST🤩

[@MotoAndy]

🤣

[@guillaumelemaire9027]

@@MotoAndy je suis admiratif comme tu te débrouilles seul pour customiser notre moto préférée Versys 1000 Forever

[@yurinidahara]

Pena que esses acessórios não chegam no Brasil.

[@antoniocarlossantos4915]

Eu consegui comprar aqui no Brasil na loja Espaço Warrior por um preço que achei justo, já realizei a instalação e ficou Topppp. Thanks Andy for your excellent video as usual.

[@patdennis3751]

So it appears as though if I choose to add a top case with brakelights, I should use the Givi base instead of the Kawasaki to avoid the issue you ran into? I am enjoying your videos by the way.

[@MotoAndy]

Well, that sounds logical, unfortunately I'm afraid that the original GIVI base will not fit the Versys, because it is of a completely different shape

[@patdennis3751]

We that sucks..

[@daltroedu]

So hard to install 🥲

[@gbinman]

It is sad that the plate wasn't designed for this modification. Poor engineering. Does Givi offer a plate?

[@MotoAndy]

you can buy a givi base plate, but in addition you need to buy an additional rack (for the base plate), the plate itself does not fit

[@pdx650]

After receiving my box of the givi E135 kit in the mail, high-lighted on the outside package in neon green says this light kit can not be used on the M8 or M9 aluminum top case mount pads. I have an alum mount on my ‘07 Honda ST1300. I am installing it anyway to see what happens.

[@duckieduck3287]

My Versys 650 comes with a Givi top case mount so i didn't have to drill holes and the like@@pdx650

[@elpstudio]

Extra

[@CasuallyGaming909]

You did great but that design has too many points of failure

[@MotoAndy]

it has been working without problems for 2 years, in my previous Versys it worked for 4 years without problems, so the conclusion is simple, if you do everything correctly, it should work 😁

[@CasuallyGaming909]

@@MotoAndy you are a great engineer bro. Great work.

[@robtempest8900]

I fitted one of these a long, long time ago on a TDM900 that had a Givi box and they are pretty robust. Had it for many years and never failed. They are expensive for what they are, and the effect is pretty minimal to cars that are generally below the eye line of those LEDs, but it's a nice little extra, especially if you ride a lot at night where they will stand out more.

[@MrBburdick]

Thanks for sharing!