Great video, fixed my goal zero yeti 500x that wasn’t charging. Thank you, super simple just unplug the battery for 30 seconds replug it in and it’s good again.
@ElectronicNoobBlogАй бұрын
Glad it helped!
@MONTY4X423 күн бұрын
Worked for me! I have a brand new yeti 500X off the shelf that wouldn’t charge. Stupidly, I waited until the night before my camping trip to take it out of the box and charge it up. This was quick and worked great. Thank you!!
@ElectronicNoobBlog23 күн бұрын
Glad it helped! Hope You will have great time with it!
@bazh604122 күн бұрын
Fantastic... just got a new one, refused to charge out the box... thought I was gonna have to return it which I didn't really want to since it was a really good limited time deal. Tried your solution and 2 minutes later it's fixed and charging! Ideal. As another poster says, no need to remove bottom screws, just the top 4 bolts is fine. So quick and easy! Thanks!
@ElectronicNoobBlog14 күн бұрын
Glad You get it up and running!
@gavinimages9 ай бұрын
That worked for me after letting by battery go to 0. Thanks!
@ElectronicNoobBlog9 ай бұрын
You are welcome!
@germann993 ай бұрын
Thanks, it worked! But the small screws don't need to be removed. 🙂 Maybe Yeti 500X Reset helps aswell: Press and hold the units and info button.
@kpj522 күн бұрын
Thank u that worked perfectly 🙏
@ElectronicNoobBlog22 күн бұрын
You're welcome!
@harrelsennez7 ай бұрын
I might have to give this a try. My 8mm input charge is not working. When plugged in the light will be solid blue. I have been charging my 500x with USB-C cable.
@ElectronicNoobBlog6 ай бұрын
I'm afraid it might be something else mine also did not accept charge via usb-c. Let me and other people know how it went and did it fix issue.
@harrelsennez6 ай бұрын
@@ElectronicNoobBlog It did not work. I let my Goal Zero go to 0%. Disconnected and reconnected the red and black cables. Connected the 8mm power cable that came with my Goal Zero, solid blue, no charge.
@ElectronicNoobBlog6 ай бұрын
@@harrelsennez Not good, sound like some sort of problem around MPPT circuitry, what about rear port 8mm?
@F76986jhg Жыл бұрын
Thanks for the video, Is very interesting content for me😊❤.
@ElectronicNoobBlog Жыл бұрын
Glad you enjoyed it!
@auburnalum90198 ай бұрын
Great video. Thank you!
@ElectronicNoobBlog8 ай бұрын
Glad you liked it!
@gadgetsnation61182 ай бұрын
Do you know how to change fuse for AC inverter of where is it? It would be extremely helpful if you can tell me.
@garethjones96945 ай бұрын
Any idea what cells they are? are i know they NMC li-ion. The pack looks like 3S9P.. can you confirm?
@cyriltarkwin7 ай бұрын
Sadly did not work for me. The ! logo still shows on the screen, then the input slowly drops from 35 Watts down to 0 and then stays at 0 with an occasional 2 seconds up to 5/10 Watts and then back to 0. Dead battery?
@ElectronicNoobBlog7 ай бұрын
Maybe it's discharged too deep - try measure voltage on that battery connector.
@yearasta72645 ай бұрын
@@ElectronicNoobBlog Can you do a video on using external power supply to raise charge so controller can read it please
@lawllipops13Ай бұрын
this just happening to me as well. recently moved and had it in storage. after taking it out wouldn't work. did you figure out a fix?
@cyriltarkwinАй бұрын
@@lawllipops13 Sadly not. I scrapped it in the end and bought a new one. I figured it's life lifespan had expired.
@georgeslouis-jeune16218 ай бұрын
do you have suggestions for same issue with a yeti 1000
@ElectronicNoobBlog8 ай бұрын
Sadly I do not have Yeti 1000. You can try open it and see if there is easy access for disconnect. Maybe it will work.
@randomthings-00014 ай бұрын
I have the 1400 and I had to flip it upside down get the cables disconnected at the battery let it sit for a few minutes and reattach. Also solar charged it to wake it up then all was fine. Should run these down to 20% or so every few months just to cycle it.