Exactly my problem! Straighten out a paper clip and removed the blockage without removing the motor. Furnace fired right up! So glad thankful to have heat again! Thanks Nagen!!!
@Rustytales6 ай бұрын
Thank you very much! I checked everything and all the parts were working, but the igniter was not receiving 120 volts. Then I found your video and cleaned this thin tube, everything immediately worked as it should! What are the engineers thinking who come up with this junk? It turns out that due to a clogged hole with a diameter of just over a millimeter, a family can freeze in the winter without heating. Junk makers, not engineers. Thank you again for your video!
@chadvaughn35595 жыл бұрын
Thank you! Saved a service call. Removed motor, used a paper clip to run in and out of the hole and fixed it!
@themexicanstaringfrogofsou5268 Жыл бұрын
I'm getting a code 2 on my goodman furnace. It says to check venter end switch. Is that the switch located on the inducer motor? Do I need to replace to inducer motor? Mine doesn't seem to have a pressure switch or hose coming out the inducer motor plumbing
@aaronrodden8121 Жыл бұрын
Fyi use a small gun cleaning brush attached to a drill....Thoroughly cleans it as the gunk will build back up soon if not done properly. Use a quick drying lube (dry lubricant) to help seal the corrosion as well as prevent more gunk build up due to corrosion.
@sabbasdsouza5 жыл бұрын
Thank you so much Nagen for sharing this. I had three flashing LED light fault code and did the same thing. Coldest night of the year and the furnace is working again. That was a real helping video.
@jerryharrison29938 ай бұрын
😅😅
@GregInATX4 жыл бұрын
Thank you So much for this video. My induction motor valve was clogged as well. I cleaned it out with a drywall nail. Thanks again for posting this video. Its was 29 outside today. I was placing a service call tomorrow just thought to give it a try and found this video. I watched about 8 or 9 but none covered this issue.
@kylefromkansas3 ай бұрын
Thanks for this video it fixed my problem. I was able to poke it while it was still on the furnace fortunately just took off the hose.
@JavierIncRealty2 жыл бұрын
TOTALLY LEGIT!!!!!! Do it and save yourself the money! Not lighting??? This is probably why! Thanks DUDE!
@captaindelaigle7531 Жыл бұрын
Thank you! Spent two hours hinder my house and all it ended up being some trash in that nipple! Didn’t have to take it all off just the hose. Very helpful and saved a good bit of money! Thank you!
@nickgoesvestmode5 жыл бұрын
This helped me too! Thank you!! I had an HVAC guy scheduled Monday and now I can cancel! Thanks!!!
@cjchand4 жыл бұрын
Just another note of thanks. I was able to use your info to fix my furnace... without even removing the blower. Thanks again!
@shawndavis92762 жыл бұрын
Thanks dude! I ended up having to take the hose off from the motor to the switch and cleaning that out I just blew on it really hard and a bunch of dust came out you’re the man
@Quejuans Жыл бұрын
Saved me some money. Somehow a baby bat got lodged in the motor and was blocking everything up. Clean it out and furnaces fired right back up
@spirenoir Жыл бұрын
Had replaced the control board, no luck...Blew compressed air into the nipple where the hose connects. Fired up instantly. Thanks for the video.
@gregorycasey22713 жыл бұрын
Thanks Nagen , that small tube was full of water and dirt on mine , gave it a quick clean and it fired right up .
@bigricyomamie11823 жыл бұрын
Your vids saved me as lot of money thank u may god be with u
@dursty32262 жыл бұрын
Bless you! all i had to do was clean out that little tube on the motor. thank you for sharing your knowledge and expertise!
@IIINEMESESII4 жыл бұрын
Thanks man all I had to do was take off the little grey hose and re seat it. It's working now just saved me so much money. My gma keeps paying out the ass to fix this damn furnace. Happens every year. Now I know what they are doing an why it only takes them a few minutes to get it working. Looks like I need a fresh hose mine is split on one end. Doesn't fit right as should I assume. Wayyy cheaper to get myself new hose an replace myself instead of calling the same damn company to rip us off. Thank you
@MrTaherikbal2 жыл бұрын
Thanks, it helped and solved my issue too. You don't need to take off motor to clean clogged nozzle just run hair pin or copper wire thru it. However opening the motor let you see clog and satisfies you.
@AdamEisan Жыл бұрын
You rock! Just saved me a ton on a service call. Much appreciated my friend!
@mr.k27443 жыл бұрын
Awesome man! I had the same exact problem and just fixed it today! Thank You! Tomr is 30* in NYC 🥶
@blackpeterose2 жыл бұрын
Nice job Sir! You are spot on with this repair. 👏 I
@Tony-tt5mn Жыл бұрын
You're the man! After trying to clear it with compressed air(no luck) I cleared it with a guitar string without taking the motor off. Hope this saves someone some time!
@wmoore02112 жыл бұрын
Thank you! This was exactly the problem! Running smooth again!
@lazbuza4 жыл бұрын
Nagen, thank you so much for your informative video. You helped me fix my problem.
@DrMidknight4 жыл бұрын
Nice video. My pressure switch was bad. I will note this for future repairs.
@roopananjappa86935 жыл бұрын
Wow! This helped me save SO much money! Glad to see people like this helping out our community!
@SoulSeeker7704 жыл бұрын
Oh my goodness!! You are lifesavers!! Thank you SOOO much!! It stopped working with 3 red light flashing. Cause: • Pressure switch hose blocked, pinched or connected improperly. I checked.. nothing wrong. • Blocked flue and/or inlet air pipe, blocked drain system, or weak induced draft blower. I have no idea what or where these are or the next two points. If any of you have an Amana Furnace and know, please help. • Incorrect pressure switch setpoint or malfunctioning switch contacts. • Loose or improperly connected wiring. Corrective steps: Inspect pressure switch hose. Repair, if necessary, • Inspect flue for blockage, proper length, elbows, and termination. Correct as necessary. • Correct pressure switch setpoint or contact motion. • Tighten or correct wiring connection.
@larrykornstadt12413 жыл бұрын
Thank you so much, wish I could buy you a beer, appreciate your sharing this. Merry Christmas my friend
@Katz69cristian4 жыл бұрын
Thank you for your video. It helped me fix my unit.
@frankborja14032 жыл бұрын
Thank you very much thanks to your video today I was able to fix my furnace just as you stated in this video
@aaronrodden8121 Жыл бұрын
This worked for me but after a year, the inducer motor started not coming on until I tapped the control board a few times with power off then turning power back on. I'm working on that issue as we speak.
@dezzyd14 жыл бұрын
Thank you! Thank you! This was a quick and easy fix!!
@rocky12664 жыл бұрын
Worked for me as well, thank you!!!!
@Death_Row_Anglers3 жыл бұрын
PROBLEM SOLVED! Thank you! I had the same problem that you did. I just subscribed to your channel. Thanks again 👌🏾
@dphillie1234 жыл бұрын
Life saver! Worked like a charm!
@thomast60964 жыл бұрын
That worked for me!! Thank you SO Much!!!
@MrPiratachido4 жыл бұрын
I like your video it help me a lot and save me money thank you my friend
@Honestandtruth4 жыл бұрын
Thanks you for sharing. Good people will always Help others..👍💟👍
@CJDowling7774 жыл бұрын
This was exactly my issue, thanks muchly!
@ejflesher9 ай бұрын
This fixed my issue. Thank you so much
@seanjfk14 жыл бұрын
Thank you soooo much for this video!
@carterbersano3475 Жыл бұрын
THANK YOU! This was exactly the problem!
@513goldybaby3 жыл бұрын
Thanks 👍 it's 23 degrees out side and feel like -10 inside watch this video and now it feels like 76 on the beach ⛱️. Thank you A++
@minee40094 жыл бұрын
Thank you so much!!! It works for me . God bless😇😇
@lel70schildofthemosthigh71 Жыл бұрын
Thanks soooo much it helped me out as well !!! Saved me the service call !!!!
@alienatedyouth7errr4 жыл бұрын
Thank you so much this helped a lot!!
@carlossantos2525254 жыл бұрын
Man you save me $ tnks for the video I did just that and it works fine now kids are happy and wife is no bothering any more 😃
@jefferycoles48132 жыл бұрын
Thank you so much. Greatly appreciated
@mikestein10243 жыл бұрын
God bless you sir !!!!
@woodlandxwarrior2 жыл бұрын
Thanks brother. I did not confirm if this is the issue just yet, but I've already kinds looked at the system, and are having the same issues. Error code 3: PS switch stuck open. I'll check it now.
@armageddon8905 жыл бұрын
What gunk are u referring to?
@bradleycole5079 Жыл бұрын
You literally just saved me and my family hundreds!!! And on Christmas Night!! Thank you very much!!!
@sandlertossone18134 жыл бұрын
You are the man. Thanks soooo much I was freezing my butt off lol
@ivancarrillo90484 жыл бұрын
Thank you so much you saved me alot money I did the same and it worksssss
@JKinLVN4 жыл бұрын
Thank you, thank you, thank you! May God Almighty bless you for this video!!!
@d.ppineda44872 жыл бұрын
Thank you for your help
@youngmultac5 жыл бұрын
thanks a ton
@thetruckandi2 жыл бұрын
7 Extremely helpful!
@danoblelaw334 жыл бұрын
F'n AWESOME>>>>>>>> THANK YOU THANK YOU
@rocbrar3 жыл бұрын
Thank you!
@Woke14404 жыл бұрын
Better clean those burners 👍🏼👍🏼👍🏼
@HungNguyen-sb1yu5 ай бұрын
I have a comfort maker furnace. Where can I find the tiny hole? Thank you.
@Triceptor783 жыл бұрын
Thank you!!!
@sharonmanetta7685 Жыл бұрын
Where did you find that switch
@kevinswaney58752 жыл бұрын
Hi, I was hoping you could give me some advice. My parents had a new Amana furnace 6 roller (model AMES801205DX installed. Unfortunately they continued to have problems with it. The seller admitted they installed too big of a furnace for their house and replaced it with a Goodman 3 roller (model AMES800604BXAA). They did not receive any refund for the price difference. My dad has dementia and my mom has Parkinson. I think the company took advantage of them, but I can't find the prices for the furnaces. Any feedback you could provide would be greatly appreciated. Thanks, Kevin
@elprimojales57043 жыл бұрын
TY!!!
@jjhatnm Жыл бұрын
My lights flash red three times just like that, but their is NO noise from the motors/fans like you hear. Mine is silent. What does that mean?
@7oriole77 ай бұрын
Thankyou much
@brandenjordan6595 жыл бұрын
I have the same one, but what kond of fan should I get
@nagenem55305 жыл бұрын
Branden Jordan is fan not working?
@eddymumford4086 Жыл бұрын
Does anyone's Goodman furnace ever flash a number 2 when running only when it's running 🤔 mine dose but I never see anyone else's I watched a lot of videos... maybe mine is the only one 😁
@isisyrafaelito34535 жыл бұрын
thanks indian man!!!
@nagenem55305 жыл бұрын
happylittlegirl thank you
@Honestandtruth4 жыл бұрын
Haaahaa 😂 you guys are funny 👍
@moecapitolnetwork29162 жыл бұрын
In my case it was a clogged filter
@blueg30274 жыл бұрын
Not sure why you had to pull the inducer lol just check your pressures with your manometer. Waste of time and money for your customer
@Nagenmaha4 жыл бұрын
Jordan G I didn’t have manometer, just to let you know that was my first time opening HVAC unit
@sonGOKU._. Жыл бұрын
This error code is the worst 😢
@kennethdandurand34722 жыл бұрын
Turn your voice up..... you are whispering.
@HenryBloggit2 жыл бұрын
Can’t hear a word you say
@df56gh4d5h5 жыл бұрын
Speak up man I can't hear you!
@nagenem55305 жыл бұрын
Jim W sorry Jim it was not well planned , perhaps next time
@sabbasdsouza5 жыл бұрын
I just turned up the speakers. It was clear enough on my TV, difficult to hear on the phone. It really helped me.
@Honestandtruth4 жыл бұрын
That's what the volume button is for and Everyone got One. This is to Jim W.
@minee40094 жыл бұрын
Thank you so much!!! It works for me . God bless 😇😇