GoPro Hero10, 9 and 8 Recording on External Power

[@mygiguser]

I am now on firmware version 1.50 and it is working with this powerbank www.amazon.com/dp/B08V7KC466 there may be other powerbanks out there that work too. This is just the one i found that works.

[@AskRemy]

straight to the point - no intros - no storytelling - raw HOW to - thanks for respecting our time

[@phaedruscj3330]

No music!

[@fishycomics]

thank you for taking the time to make the video and presenting all three cameras, you should have pressed record after the battery was placed in, in order for us to correctly record,

[@chrishockleyoutdoors5419]

This is an excellent video that helped me tremendously. I have not been happy at all with my GoPro10. That accept randomly, and will allow you to record without the battery sometimes but not others. It seems that this is a good workaround and is currently working fine. There’s all sorts of issues with this camera including overheating. Just sitting on the tripod. I think it’s sad that GoPro doesn’t have any competition to keep them on their toes.

[@mygiguser]

Great to hear!

[@m.dennis]

There's the Insta360 Ace Pro now

[@Justsomeweirddragon]

They say if you remove the battery and only use the external batteries the overheating will be no longer a problems

[@mygiguser]

firmware 01.16 fixed this issue 😀, but today trying with version 1.42 it only worked once. Strange behavior, i don't know what's going on.

[@RandomDude989]

Thanks for reporting this is fixed. So the GoPro 10 with firmware 01.16 or newer works just like the 8 and 9 now? I'm looking to buy one is why I'm asking.

[@RolfResler]

So with the 01.10 firmware the Gopro 10 behaves like the Hero 8 and Hero9 now? I was planning to get a Hero10 but usually I always record with a permanent supply.

[@4audio]

@@RandomDude989 no preview while recording on your phone!!!! 9 and 10 gopro same sh.....

[@Kendzior944]

Great! I bought the 10 for airsoft, and I will be primarily using a powerbank to keep it going, I also need to 3d print that doors with the hole in it to keep it just a bit more secure from the wheather

[@dalibor2311]

@@RolfResler For how long do you record with a permanent supply and which video settings? I plan to record in 4k 30p for 2-3 hours. Would it work? or shutdown because of overheating.

[@Stellarbaits]

Was having issues with powering my hero 10 with a portable power bank. This did seem buggy but was very helpful. Seems order of operation is a factor with the Hero 10. Plugging directly into the hero from the power bank when the camera has NO BATTERY in it was a fail. After this video I tried turning on the power bank FIRST, and the plugging into the hero while the BATTERY is still in the Hero. Then removing the Hero Battery and the power stays on. I also experienced the blacked out screen, but it seems to go into sleep mode quickly but is still working/recording. Although it didn’t work in this video, tapping the screen brings it out of sleep mode. Although this video wasn’t focused on my particular problem, it was highly detailed and help me figure out my issue very quickly. Great video, thanks so much.

[@HansBrevik]

This was just what I was looking for! Thank you very much 🥰

[@WanderingMonkHikes]

I have been shooting night time lapses for 9 hours at a time on my Hero 10. I don’t remove the battery, but simply plug in the external power bank. It works fine. I haven’t tried removing the battery.

[@mygiguser]

the thought behind removing the battery was to avoid/delay overheating.

[@WanderingMonkHikes]

@@mygiguser That’s logical, but if you open the door (I use a special door from GoPro with a port for the USB) and mount the camera on a stick (I use the shorty) there is enough air flow to keep it from overheating. There are two small ports under the mounting thumbs that dissipate heat. People mistakenly leave the thumbs closed and sit the camera on a flat surface. Then they have problems.

[@voidwareprohibited]

@@mygiguser The Hero 10 doesn't charge the battery while recording, it just uses power to operate, so shouldn't overheat.

[@Bonzi_Buddy]

What is the longest time have you gotten your setup to go?

[@WanderingMonkHikes]

@@Bonzi_Buddy last week I did a night lapse from 7pm to 6am. Then I switched to day time lapse settings from 6:30am to 8am (total 13.5 hours). I was connected to a 20K ma power bank. It used about 25% of the power bank.

[@paragsj]

Great video. Exactly what I was looking for.

[@JapanCycling18]

Im your fan now, count me on too

[@jerseyshoredroneservices225]

Thanks for making this video and to all the people who commented with helpful suggestions. So I just got a go Pro for the first time last week and realize I needed longer battery life so I bought the loom cube battery grip and thought I was set to go but unfortunately the GoPro just used up its own battery and shut off, leaving the external battery fully charged :-( I can't find a firmware version but I do see where it says camera version 01.42. I also saw that it said the firmware is up to date.

[@HighCarbAlex]

Apparently it's fixed now

[@jerseyshoredroneservices225]

@@HighCarbAlex That camera was a GoPro 10. The solution was a manual firmware installation off of the SD card. Unfortunately since then I've learned that the 10 and 11 have very delicate back screens. Both of mine broke without ever being hit or dropped. A search for the issue reveals that many other people have had this problem with their GoPros so it's not just me. My 11 broke the first weekend I used it in Nov 2022. I made a warranty claim and GoPro told me to get lost. So I learned the hard way that GoPro cameras are very expensive disposable cameras :-(

[@HighCarbAlex]

@@jerseyshoredroneservices225 go with a DJI action 3, that's what Im currently doing. Cancelled my hero 10 order and went for action 3.

[@HighCarbAlex]

@@jerseyshoredroneservices225 also maybe worth getting the go pro subscription for 25 bucks and trying to get it replaced that way

[@jerseyshoredroneservices225]

@@HighCarbAlex Ive had it since I bought the first camera. Unfortunately they don't just replace the camera, they charge you I think $100. Considering that they are defective cameras I don't think it's right to be charged for a replacement. Especially since I have two of them and the 11 broke the first time I used it, I just can't give GoPro more money...

[@RichardsWorld]

My GoPro 10 was shutting off a lot outside the last couple days. I'm going to see if it stays on using external battery and door open.

[@BigManAlaska]

Well that's a big help when mounting it for a dashcam device which is something I planned on trying tonight for my next video.

[@BigManAlaska]

I did notice that it will charge the battery if the screen is on and not recording. But maybe that's a well known fact 🤗

[@HondaRider_600rr]

hi to all for hero 10 we have to have a very Good power 2.1 amp or more and charge Boost cables do help too ... note your power bank may say its 2.1 or 3.1 amp charger a lot of cheep ones out there .. my hero 10 gave me problems with two different power banks one was new 3.1 amp would not even work ... so good power Banks & cables should help😏 A belkin 20k power Bank and Belkin Boost Cables should work Fine

[@porteneur1]

Interesting comparison. hope they fix that bug on the next update hopefully Gopro will see this. thanks you Sir.

[@pratikvyas1172]

am getting this issue now and is not 100% fixed

[@chiribimchiribim]

which external power solution would u recommend in order to record a timelapse for 2 days? thanks!

[@jesperkrautwald5594]

Very good informative video. I'm still a bit confused though: Has the firmware updates in the Hero10 made it possible to use it as with the H8 & H9? I imagine that running on 'external' power only will minimize the overheating problems many users complain about?

[@mygiguser]

It needs more power than the H8 and 9. And sometimes it just doesn't work, other days it's fine.

[@SideHustleInspiration]

Are you getting clicking noises sometimes in your videos?

[@rapaent]

I received my Hero10 today.....My power bank worked flawlessly. The following are two ways to use a power bank; FOR SOME REASON, EVERYTHING WOULDN'T FIT IN THIS COMMENT. I WILL FINISH IT IN "REPLY" BELOW 1) You need to leave the battery in camera for all functions and screen to work properly. Setup: Plug in your power bank > Red indicator lights will be on solid > Turn on your GoPro > Solid red light will now turn off > Battery bar on screen will show your battery is charging > Operate GoPro as usual > A functions are available. Note: a) Battery will charge if the power bank is plugged in while "not" recording or turned off. When turned off the Red indicator lights will be on solid while charging. b) Battery doesn't seem to charge while recording but, it remains at the same percentage. I recorded for about eight minutes which showed the same percentage as when I started. c) I repeated this process three different times without any problems.

[@rapaent]

2) If you remove the battery and then plug in the power bank you'll be able to see your screen but, once you hit the record button, the screen/s will shut off. Stop recording and the screen/s will come back on. All functions are then available for you to see.Setup: Plug in your power bank > Red indicator lights will flash once and turn off > Turn on GoPro Hero10 > Battery indicator states No Battery > All functions are available > Start recording (screens will be off until you stop recording) Note: After the first time of recording and pausing you will hear a beep and a pop-up will appear stating the following; Cold Battery AlertYour GoPro battery is below 0°C, the displays will turn off during recording to maximize operation and runtime. Press OK This "won't repeat itself for any more consecutive recordings unless, you power off the GoPro Hero10 and/or unplug your power bank. This should work out for any power bank. I've had my Anker power bank for about four years which has worked all day easily on my Hero7 Black without any problems. It appears the it's unavailable now but, the following is an Anker link to that power bank. Anker has many others to choose from and has a great rep. www.anker.com/es/products/variant/powercore--10050/A1311011

[@dinbali]

@@rapaent thanks for your comments!

[@rapaent]

@@dinbali Your welcome.... 😊👍

[@mygiguser]

@@rapaent I compared the 9 and 10, and i see both pulling a max of 1.2A but the H10 has the screen off as soon as it is recording. With battery inserted, and recording, it still uses the same amount with 1A with spikes to 1.2A. My USB power supply can handle 3.1A And with low battery inserted, and NOT recording, it pulls 2.1A

[@zoranstary7229]

Guys, you’re genius. I was searching this kind of explanation/instructions. Great job done. Thank you so much 😊!!!!

[@guidingstars9840]

hey. currently the hero 10 has not available for external power ? ,, would be very frustrating cant use an external power thank U , I am new subscriber

[@kikalunas7449]

Hmmm! Im new to gopro and have just bought a hero 10 still being trialled before i use it for a forthcoming road trip through the Swiss passes and theB500 Black Forest and want to record the whole of these sections by using a usb cable in my car to avoid changing batteries every 35-60 mins. When following your test conditions whilst plugged into my usual iphone usb plug charger, it all works perfectly in various combinations but when trying the same in my car i get a a blank screen saying connected into usb and no functionality. I have only one option by starting the GoPro 10, and press record and lastly plug in the usb-c cable which then shows it is charging. alas, if i stop recording i get that blank screen again saying usb connected and no functions. I will try calling customer support tomorrow to ask whats happening as my car usb-c ports work fine charging my iphone

[@riverrat92]

I have a hero 9. That records fine with battery. If I try and record with only charger it shuts off when I press record. It’s driving me nuts. Any advice?

[@rabbit5717]

Very good! I can now use my charger cable wrapped around my Yak Attack pole with my 9! Fantastic! Thanks

[@immanuelroach]

What firmware was the hero 9 on in this video I want to know if the external power will work on the hero 9 1.70 firmware ?

[@mygiguser]

Firmware1.72 is what i used. Don't know about 1.70

[@alexei__96]

хорошее видео! только что купил гопро 10, пробую ваш тест!

[@ibrahimomar2335]

Hey, kindly please. I really need to know. If you can answer my question. How long I can record constantly with GoPro8 while plugged in terms of memory or memory options? How I can record as long as possible? And is there a way to have it record constantly while it's deleting older part of data to keep recording so I can pull out the part of data when a serten event happens. I never had GoPro before. It would be very helpful of some helpes with this. Thanks

[@mygiguser]

i personally would not trust a GoPro to long term record. How long you can record depends on temperature, the capacity of the SD Card, and luck.

[@ibrahimomar2335]

@@mygiguser Thanks for helping I'm going to consider a monitor camera instead.

[@busyguy925]

Thank you ! very useful hack . shouldn't be made that hard by the manufacturer , but you figured it out

[@cancion5791]

Your voice reminded me of Hans Zimmer, good video👍

[@markobizjak3736]

I am filming how the flowers are drying, and I have the camera connected to a power source. Does the recording automatically save when the SD card is full?

[@mygiguser]

idk, i always use very large SD cards and never tried that scenario. But knowing my Hero11, i believe it is more likely that the camera will crash before it is able to fill up the card.

[@markobizjak3736]

@@mygiguser I think recording Time Lapses doesn’t make very big files and I will probably be filming for ten day, so guess everything will be fine. Thanks for reply 😃 I also thinning to buy 11 🙂

[@ianM449]

tried it my hero 9 and it works

[@sylvie90313]

I use my GoPro when cycling. I do not like the idea to ride without the door in place. I am affraid a lot of particles could enter in the GoPro. What could I do ?

[@mygiguser]

You could use the Media Mod

[@sylvie90313]

@@mygiguser Thanks for you quick response....I have just watched on KZbin what is Media Mod... sorry but I don't understand how it could work...to put out the battery you have to disconnet the USB-C cable, right ? so it wouldn't work... maybe I don't understand the Media Mod...

[@michaeldunlap3401]

Mile marker mike here: when I use to keep the battery and use external power for longer recording time I would get overheat I no longer have the internal battery but just operate the GoPro with external only no more over heat problems in high temperatures so why don’t you just turn it on and off with external power minus the internal battery

[@yomeportobien]

I’ve used mine for months with no battery, just power supply. Then one day, out of nowhere started doing this. Is any way to fix it?

[@mygiguser]

Did you get an update on the camera? Otherwise, i don't see why it would stop working!!!???

[@yomeportobien]

@@mygiguser I did upgraded the firmware but was right out of the box. I've upgraded today again and the sign started popping, before just shut down. I've tried the iPad charger and worked! Notices that the sign says 5v 2a. Haven't checked with a external battery yet just plugged into the wall.

[@bandit911]

My GoPro 9 works with power bank through the media mod as long as the GoPro battery is installed, if no battery installed then i can't even turn it on with the power bank

[@sequoiasemperviren3163]

In all of the videos I have seen on youtube regarding powering Hero Black GoPro cameras, not one has offered to say what the power source is: 110 volt ac? 12 volt dc from car? Power bank? Very frustrating.

[@mygiguser]

the powersource has to be 5V thats what GoPro needs!

[@sequoiasemperviren3163]

@@mygiguser Thank you very much! I will look for a power bank that gives out 5 volts and I understand 3 amps. The Anker PowerCore 26800 mAh appears to be able to power GoPros.

[@pootthatbak2578]

Im trying to record 20 hour time lapse. With the hero10 black..crashes, unknown reason. Im currently running it voice command disabled..im worried it hears me say go pro and turns off.

[@mygiguser]

Well, for me the Hero11 works much better!

[@digflfishing2177]

I have a big problem with mine overheating. I film in full sun a lot in Florida. Any suggestions? I'd like to make longer videos but at current, they end up short because I can't get too much time out of the camera. I watched your video because I was wondering if removing the battery pack and using an external battery might help keep the camera cool? Any thoughts?

[@mygiguser]

What GoPro recommends is to turn off GPS and WiFi, and then go with a lower frame rate, and maybe turn off Max stabilization, and run it with less stabilization. I image on a boat with constant movement, the stabilization is very busy, what could cause the fast overheating. External battery is not bad, but then the camera is not waterproof anymore...

[@bananafueledgaming8399]

lol gopro is an idiot why buy a hero 10 if the features are not usable. if thats their solution to tone down the settings then the hero 10 is not worth the upgrade

[@jerseyshoredroneservices225]

Like the other comments says, turn off those features if you don't need them. Also create shade and ventilation for the camera if possible. Lastly, remove the battery from the camera and power it with an external battery. Leave the battery door off for better ventilation. Obviously this doesn't work if you're going to get it wet. whatever you do be super careful because the back screens on the 10 and 11 are super delicate. I broke two of them one very new cameras without dropping them or hitting them with anything. I made a warranty claim but GoPro told me to get lost 😡

[@CurrentJAM]

This used to happen to me also especially if I kept the battery in while it's plugged to an external power bank. I have found success when using only the external power bank and removing the battery.

[@SideHustleInspiration]

I have a questions for you. I received a GoPro hero9 replacement camera. The video recording is excellent. But, I occasionally hear "clicking-popping" noises in some of the videos. I noticed you said "poipping" is what it sounded like to me. How do I overcome this do you know?

[@ZeroTraveler4]

What is the external power supply voltage for gopro hero 8..will it damage the gopro??

[@mygiguser]

they are all 5V

[@lukelloyd1985]

Do you know, if there is no power to the GoPro (battery or external) does it lose any configured settings?

[@PEVRidersClub]

I just checked and tried to charge thru the media mod on my GP10 and it works only IF: 1. You use the GP provided usbc cable only 2. You have to remove the battery of the camera. Great video BTW thanks for sharing it 👊 #PEVRidersClub

[@SideHustleInspiration]

And do you hear clicking noises in your videos sometimes?

[@m.philip]

Thanks for the video. Just tested my Hero 10 - with no battery and only external battery the display (front and back both) is turned off when recording. Maybe its by design. If not expect a firmware update.

[@mygiguser]

Hero8 and Hero9 can do that without issues. By design means things get better and not worse. I guess not with GoPro.

[@UTdky888]

Get an external battery with USB type C output. Connect the external battery to Gopro hero10 with the USB-C to USB-C cable will work without the battery error message, even with the latest firmware update. No need to insert the internal battery. Thunderbolt to Thunderbolt cable also works. Do not use USB-A to USB-C cable.

[@HoffmannChristoph]

I have the same issue with my hero 10. Doesn‘t power on external battery. However if I plug it into the mediamod it works. Very mysterious.

[@cncpopc5456]

Not sure, a bit of a puzzle, ...BUT... this version (10) is configured to work as a cam=>external video source (mixer, or ext recorder, or webcast). In THAT mode the GoPro rear screen goes black as you INSTEAD view from the external system monitors ((mixers, matrix whatevers, etc). ALSO no matter what GoPro video format is set as active format the output from the cam out (using the housing) is 1080p. Again a GREAT thing for live web cam but is unlike prior. I don't know of any switches including iPhone control. ???? Not a "glitch" but a "feature"? :-)

[@cncpopc5456]

Forgot to add (kind of obvious) that the housing out is TWO ports: HDMI (1080p) & USB-C (power).

[@mygiguser]

What housing are you talking about? I didn't use any housing in my video??

[@cncpopc5456]

@@mygiguser =>THAT

[@henrytwigger2245]

Is the power supply delivering enough power for the Hero10 ? It uses more power than the 8 and 9.

[@mygiguser]

yes, i tried different power supplies, including a power pack, and the GoPro supercharger. All show the same result. Tried different batteries too. The external charger is able to charge the battery to 100%. The Hero10 and Hero9 batteries seem to be the same.

[@jacobgray6949]

Has there been a resolution for this? I want to try this for timelapes at work to keep it from over heating

[@mygiguser]

with wifi and gps and displays off, it doesn't get that hot during time-lapse

[@swvlogsandinfo]

i try My gopro 10 its work without betry ....But 5v 3am power adapter and same power bank ..Fine working Mostly video vlog making power bank atached betry removed and making vlogs

[@SteveWB]

I think the GP2 chip draws more power and the power cord was enough for the 8 and 9 but not the 10 so try a different power supply or a battery bank.

[@SteveWB]

I should of watched the rest of the video before commenting lol

[@mygiguser]

I compared the 9 and 10, and i see both pulling a max of 1.2A but the H10 has the screen off as soon as it is recording. With battery inserted, and recording, it still uses the same amount with 1A with spikes to 1.2A. My USB power supply can handle 3.1A And with low battery inserted, and NOT recording, it pulls 2.1A

[@SteveWB]

@@mygiguser very good!

[@bills5423]

@@SteveWB Had same issue. Will take pix fine w/o battery, but not videos. Changed to a battery pack that exceeds 1.0 amps and it works fine. So the packs that limit to 1.0 are the problem

[@bills5423]

further observation- 1.0 amp Works with the "standard" setting 4k/30, but no higher FPS

[@toxinaofdead]

Acabo de realizar la prueba, y lo que sucede es que la cámara no soportar realizar las grabaciones en 5.3 k. Como lo realiza la persona del video sin batería. Si la bajamos aúna resolución menor a 4K si que se puede. La siguiente prueba fue. Que si requieres realizar una grabación a 5.3 k con una power bank a ala GoPro 10 si se puede solo que no tienes que sacar la batería. Y conectar el power bank

[@mygiguser]

Interesante

[@ayushmohanty4522]

Sir is the battery door of 8 and 9 are same?

[@mygiguser]

No, 9 is wider.

[@jerseyshoredroneservices225]

I too had the problem with the 10 not charging from the external battery. The solution was a manual firmware installation off the SD card. Support gave me a link to download the firmware, copied it from my computer to the SD card and put the card in the GoPro. when the GoPro started it founf the firmware update and installed it. That fixed the charging problem. Unfortunately soon after that I learned that the 10 and 11 have very delicate back screens which broke on my cameras without ever being hit or even dropped. The screen on the 11 broke the first time I used it. When I made a warranty claim GoPro told me to get lost. These are very expensive, disposable cameras 😡 When my 10 and 11 become unusable I'm switching to DJI. In general I'm trying to get away from Chinese products but GoPro is pushing me back to China.

[@mygiguser]

Do you remember what firmware version they told you to use?

[@jerseyshoredroneservices225]

@@mygiguser I just looked. 01.46.70 When the camera boots on startup it flashes a message for a second... GoPro Labs Beta Firmware... This is the GoPro 10 and I got the firmware from them about a year ago when I started doing this stuff, just before the back screen cracked LOL

[@roshansmith6560]

thank you for this video

[@youtoob8166]

mine keeps saying not enough power must have 5v2a .i have tried with many power packs and chargers.

[@mygiguser]

try a different cable. best to use USB-C to USB-C.

[@Landelutt]

Works with my hero 10. Probably to weak charger that works with older less wattage heavy stuff but not with hero 10. Try the same thing in battery saving mode and it might work =)

[@lukelloyd1985]

Good video thanks for taking to time to do the comparison. The only test missing I guess is using external power only (no battery from the start) to power on and record, do you know if that works on all three?

[@mygiguser]

it works with 8 and 9, but not with 10

[@brokenpistons]

Interesting, even with the updated firmware?

[@brokenpistons]

I wonder why they removed that feature with 10 🤷‍♂️🤦

[@PEVRidersClub]

I just checked and tried to charge thru the media mod on my GP10 and it works only IF: 1. You use the GP provided usbc cable only 2. You have to remove the battery of the camera.

[@whysoserious13218]

I bought my last Gopro in 2014~2015 and I waited until 2022 bought gopro hero8 and I'm good with my decision at least I can record my gopro continuously with power bank and reserve the battery for like underwater activities

[@XploringwithAde]

What power bank do you use and how long does it last while recording thanks

[@whysoserious13218]

@@XploringwithAde I use anker 10,000mha I recored it the last time for 6~7 hours without problem and the power bank still had more than 50% battery

[@XploringwithAde]

@@whysoserious13218 thanks for that do you leave the battery in the GoPro when your recording with the power bank Thanks

[@whysoserious13218]

@@XploringwithAde yeh I connect it through type C cable ... amazon sell the battery door with a hole for you to use with the cable or you can just remove the battery door on gopro Should be fine

[@antigonooo]

When i connect my hero 9 to the usb outlet in my car it says its collected to cable and does not work

[@mygiguser]

maybe your car usb hasn't enough power

[@antigonooo]

So automatically the GoPro think is connected to a pc. I sorted it out connecting it trough 12v plug and now works

[@BX0207]

See thats why I love my GoPro 5 and 7./ The usb port is apart from the battery and micro card. Now you have to remove the battery door and expose the elements to be able to record from power bank.. .. its as if they did that on purpose to make you wanna buy batteries

[@shahrilaril1492]

Thanks for sharing this video 👍🏻👍🏻

[@charlescasselman977]

try it plugged in with a dead battery. i don't see the reason for recording without a battery. if you have it plugged in then why take the battery out.

[@punisherofArizonaUtilty]

Thank you

[@punisherofArizonaUtilty]

We did this for the Labor Day parade. It was super helpful. I have a few videos from the event on my KZbin channel

[@jeremymclaughlin917]

So that side isn't the battery, WHAT IS IT.!?

[@Remove_Before_Flight]

My GP 10 works fine without the battery. Although it shows low bat temp. constantly

[@mygiguser]

that's odd, i would expect that they all behave the same way.

[@OrlandoavancoPescaesportiva]

Tenho 1 go pro 9 a 1 ano de uso com.pescaria ligada dia todo nonpower bank baseus 3000 ha

[@mygiguser]

good for you!

[@LANTER2300]

Is a baddery the same as a battery ?

[@mygiguser]

it is

[@FlattyDaz]

Same problem with my gopro 10…… i cant use it on my fishing kayak with an external battery, extremely disappointed with Gopro, even called Gopro and they wont even admit there is a problem, so in a few days i plan on using anothet action camera on my kayak and film me throwing my Gopro 10 into the ocean and i will be sending a link to my video to the CEO of Gopro and hope he enjoys it 👍🏼😊🎣

[@mygiguser]

I feel your pain, but my Hero11 doesn't have all those problems. I said 'my' Hero11, because with GoPro you never know ...

[@scorpnz4433]

Not impressed with the gp10. For the dam price paid for it i find it pathetic you can't record while the charge cable is attached even if the batt is close to full & instead you have to go through the rigmarole of recording first wtf. Glad you made the vid for the work around

[@jerseyshoredroneservices225]

I had that problem too. This solution was a manual firmware installation off the SD card. unfortunately soon after that I learned that the 10 and 11 have very delicate back screens which broke on my cameras without ever being hit or even dropped. when I made the warranty claim GoPro told me to get lost. These are very expensive, disposable cameras 😡

[@rapaent]

New Battery coming by the end of November! GoPro anounced a new improved battery called Enduro which will be a big improvement that we're dealing with now. Check it out here; 😱 gopro.com/en/us/news/hero10-black-video-performance-modes-and-enduro-battery

[@sosuaevents]

This is perfect.

[@entre.navajas]

Te amo me has salvado con este video ❤❤❤❤❤😅

[@jujumooz9784]

Extended Battery Module For GoPro HERO10 Black & HERO9 Action Cameras - Digipower

[@fishycomics]

I ran again this test, got the uickCapture to turn on like the Mode On, kzbin.info/www/bejne/j2STf5Rvmqagj5o

[@dashcameraro2031]

Not worked for me

[@Rev_n_xplore]

What about mic

[@kabolamoto-8611]

thanks sir

[@OrlandoavancoPescaesportiva]

E moro na Rondônia aqui 1 calor do samurai

[@dimitrimoonlight]

GoPro hero 10 has GP1 Prosser which is power hungry.

[@SuperRealityKid]

Such a time waste sorting out these GoPro problems that they should have worked out before taking your money. Gopro will tell you it is anything but their fault. The GoPro tech people know exactly what's happening but the marketing people deny deny deny. ("We've got units to move here, tell them anything to keep them buying") The problem is that the software developers are trying to do everything to attract buyers by offering more and more features but then leaving it to the public to beta test them. The newer the firmware, the more buggy they are. I have rolled my 10 firmware back to 1.2 and it is working fine for me. Probably missing some refinements but at least able to get through 2 hours of recording at 4K, 60 fps, high bitrate and not overheating. I can now get back from a flight in my aeroplane and not find the external cameras stopped working after 40 minutes. Seriously looking at DJI after being a Gopro fan and purchaser since the Hero3. 😡😡

[@mygiguser]

You are right, but what surprises me is that the new Hero11 that i got works so much better than all the others. How is that possible?

[@jerseyshoredroneservices225]

When my cameras become unusable I'm switching to DJI. In general I'm trying to get away from Chinese products but GoPro is pushing me back to China.

[@rapaent]

Take the battery out before connecting and turning on...... You're confusing the software in the camera.

[@mygiguser]

the software is not confused on the 8 and 9, but only on the 10?

[@rapaent]

@@mygiguser Thanks.... I sure hope this getr figured out. I use external power over 70% of the time on my Hero 7 Black. I have a 10 on the way. Thanks again. 👍😊

[@mygiguser]

@@rapaent did you receive your Hero10 yet, how does this work on yours? Any luck?

[@rapaent]

@@mygiguser I'll be receiving it next week. I'll let you know here. 😊👍

[@rapaent]

I placed my testing under Comments further down. 😊👍

[@pratikvyas1172]

@mygiguser i am stilll getting this issue with brick wall charger but dont get it with laptop or Car charging point with Hero10