Here's an Amazon affiliate link to bolts similar to the ones I'm using in the vid: amzn.to/3IvlWPv
@MdShohag-wc9io6 жыл бұрын
Gosforth Handyman নাবাক
@naranarayangoswami79105 жыл бұрын
Gosforth Handyman
@imranmughal92314 жыл бұрын
i am from pakistan wall bolt machine chahya pleze send the cell phone ya cal me 03006428815
@emhavaemhava80294 жыл бұрын
Would you recommend using those in the mortar/cement between bricks/concrete blocks? Thnks
@PinoyTechTutorials4 жыл бұрын
you deserve it sir!
@pureretro59795 жыл бұрын
I used one of these on a garden gate where the screw kept getting pulled out of the sandy cement wall. It was totally overkill for the job but it worked a treat and the gate bracket is still 100% solid 7 years later.
@sandorkovacs92715 жыл бұрын
fixing anything to anywhere, a man cannot finish the job without saying this: THIS ISN'T GOING ANYWHERE. love it :)
@themaldivian41153 жыл бұрын
Hahah so true . We say that all the times after doing any fixing work. I guess it's a universal thing
@mrslkungpowchikn1206 Жыл бұрын
Been Looking for this for over a year! Now, how do we deal with a cinder block exterior wall with a plaster board lining it’s interior? It covers 2 walls of our smaller size bedroom and my son’s small bedroom. Need to hang heavy duty floating shelves for books and also, heavy paint cans! lol (I don’t like them outside because the constant cold temps and then super high summer temps tends to ruin them! 😂
@Luka11808 ай бұрын
Hope you eventually found your answer
@AtticEntrepreneur2 жыл бұрын
Great tip about installing the bolts in the anchors onto the thing to be mounted and then inserting them into the drilled holes! I tried it by installing the anchors in the wall and then screwing the bolts in, but one of the bolts wouldn't grip and then it was a nightmare trying to get the anchor out of the wall again. All done thanks to this great video, thanks!
@ipod19786 жыл бұрын
Good video pal. For anyone looking to use these with only a standard masonry bit/hammer drill you can get away with using a bicycle pump and a needle tip (like you would use to pump up a football) to blow out the excess debris and dust. Messy but it certainly clears the cavity enough to allow a solid install.
@michaelnobibux28866 жыл бұрын
Junior J I sometimes use a can of compressed air (the kind used to blow dust off electronic circuit boards).Works great!!!
@marcoliver7914 Жыл бұрын
Thanks so much for that recommendation. I'll defo give it a go.
@ianjohannes75243 жыл бұрын
Just wanted to thank you for your video. This was what pointed me in the right direction. Where I live, most of my walls are ultra dense, reinforced concrete - kinda stuff used in UK high rises in the 60's. Anyways, I weight 130kgs and so bought a hefty pull up bar which is wall mounted with four M10 rawlbolts now. Never felt anything so solid. I then decided to get gymnastic rings and so SDS drilled into the ceiling, which is also this god-like super concrete (took ages) - installed M10 eyehook bolts and hung 200kg load carabiners and gym rings (straps and gym rings can hold 450kg each). I still was a bit concerned. Until I set one gym ring about 5 inches off the ground and put all my weight on it....for for 10 seconds I swung gently back and forth...all 130kgs of me. On ONE BOLT! Called RawlPlug UK to see if this was OK and Adrian laughed and said I could have 3 of me on one, and the carabiner and gym rings would give out before this single rawlbolt. If it wasn't for your video I would have never been able to get myself the gear I need to get in shape at home. So a huge thank you. I have subbed. :)
@osh2023 Жыл бұрын
Thank you for the notes on how to pull these out. I have a few installed and I was worried on what to do in case I wish to take them out in the future.
@blackbird86323 жыл бұрын
I use these for hanging the swing for our kid. It even supports my full grown weight. Awesome fixings.
@tambade14 жыл бұрын
You're the best, these came with a wall mounted punching bag that I got, wasn't sure how they worked and how to install them. Thank you for this video
@TheGunzSkido4 жыл бұрын
Can you install it onto wood?
@lw72283 жыл бұрын
Best video I have seen how to attach these. Clear and concise. A pearl between the rubbish out there. Keep making these video's. Thank you from Holland
@Chris.Brisson2 жыл бұрын
I just saved me much grief with the tip on how to remove a wedge anchor. It worked easily.
@rivolinho3 жыл бұрын
Great video. About to fix a gun safe to a solid wall and never used these fixings before. Very helpful!
@ystebadvonschlegel32954 жыл бұрын
"that isn't going anywhere" - universal man saying across the world
@stonermagicinc.63432 жыл бұрын
I was thinking the same when he says "beefy hole" 2:47
@mokodo_2 жыл бұрын
That's so accurate
@Aliwala692 жыл бұрын
Excellent video on how to use Wall Bolt with details. It makes my life easy now to use Wall Bolt.
@Orion742054 жыл бұрын
I hope to be using these exact bolts to wall mount a display cabinet to an exterior wall in a small bedroom. Never used such a thing before but you make it look so easy, thanks!
@ShaukatHakim5 ай бұрын
Just happened to watch this video and found it very useful as I needed it before starting a job I have to carry out. Thank you very much!
@Neilgal124 жыл бұрын
Great video. Quality explanation, quality filming and editing - none of that’s easy, but you made it look easy. Thanks!
@BigTastey3 жыл бұрын
Followed this step by step when I hung my heavy punch bag! Went to B&Q bought all the wall bolts and very similar drill everything went great. Thank you for this video mate!! 🙏🏼 👍🏻👍🏻
@chiefnkosi77053 жыл бұрын
I'm actually watching to hang my bag
@BigTastey3 жыл бұрын
@@chiefnkosi7705 Check the wall your using will be able to take the weight first mate. I hung mine from the wall inside the garage [normal house brick] and after a month the mortar between the bricks started to crack from the heavy weight and me punching fuck out of the bag!! Think I’m going to have to go with a free standing bracket now.. 😢😢
@chiefnkosi77053 жыл бұрын
@@BigTastey my wall is made up of concrete blocks which filled with cement and the wall is plastered up with more cement so I can't see where mortars are. How can I check this?
@t190uk3 жыл бұрын
I can't believe u drilled ur garage floor just for a demo....fair play! Great video 👍
@jessielang8331 Жыл бұрын
In UAE here and living in Dubai from one of the old buildings.....Im planning to do this in my room to bolt a pull up bar. I need to drill 4 holes... 2 on each side. I think drilling is not an issue though not so sure if ill be hitting some cables or if its a solid block. Been checking videos on how to do this...
@raymondpauly55765 жыл бұрын
Best video I could find on how to use expansion bolts.
@ethanf.68483 жыл бұрын
Glad to see that you could remove it from the floor at the end of your demo!
@johnhanley18904 жыл бұрын
I used these 30 years ago to secure metal post supports to the top of a concrete wall, they’re as solid today as the day they were fitted.
@johncroasdale19924 жыл бұрын
I have used these fixings to hang up a chining bar for doing pull ups definitely the best for the job
@mohamedharif77553 жыл бұрын
Bro pleas tell size
@mohamedharif77553 жыл бұрын
for same purpose
@manzildeuja6665 жыл бұрын
this is just gold ....thanks for the in depth tutorial. hanged it on my wall for wall mounted pull up bar. now i have to pull it out again and shift it another place... this informative vid' helps putting it in and pulling it out ;) XD
@grzegorz161004 жыл бұрын
That is what I will be using it for
@helios33094 жыл бұрын
Is your pull-up bar holding up. Mine fell of the wall in 10 days after installation.
@qEnergize4 жыл бұрын
@@helios3309 Seriously?
@steelydan12422 жыл бұрын
Thanks buddy. I had a few of these wall bolts in the tool box and not knowing what they were for or how to use them untill now.
@mw2159Ай бұрын
Do you use a drill bit that is 1mm larger than the bolt/anchor? I drilled using 12mm drill bit on the wall, and went in out a few times. But the 12mm bolt/anchor can't seem to go in. I abandoned it now as I did not want it stuck halfway and I have to use pliers to get it out or have to hammer it in.
@edward_grabczewski4 жыл бұрын
What an excellent video. I've been struggling trying to get mine to expand and I think I'll need to use a bit of resin to help but at least I finally understand how they work. Cheers!
@trecker593 жыл бұрын
I used the old 1/4" whit Rawl bolt on heavy hanging basket brackets some 40+ years ago and there still solid, I have removed and refitted them many times for painting also using the same bolts.
@Sophia-dq8xj3 жыл бұрын
Thank you for this video, without it my husband would have made a couple of mistakes. Very informative.
@madeinyorkshire220311 ай бұрын
Great video! How would you fix something very heavy to a single leaf garage wall, please? Thanks
@RAINE____4 жыл бұрын
Mate, I've got no interest in DIY/joinery at all but these videos are mint. They're so relaxing. I've seen you dismantle two hotels, renovate two houses, inspect a couple of new builds and now demonstrate some mad claw anchor bolt things. Awesome.
@nowthenad32865 жыл бұрын
I am spending my evening watching a video of a bloke balancing his entire body weight on the top of a bolt...and finding it weirdly enjoyable. Great videos
@gustavou2865 жыл бұрын
I guess u r fucked up man
@syl7648 ай бұрын
Now a video in real time of you putting one back together when it comes apart. I bought 20 yesterday and 4 of them fell apart. Unfortunately I needed to use 18 and Screwfix had now closed. I spent more time putting two back together than I did fitting the rest of the shelves!
@leegriffiths3123 жыл бұрын
Best explanation of anchor bolts on here! Thank you
@nyegrant59372 ай бұрын
Great video, thank you. I have a question…for stationary items I imagine this would be perfect but would this be suitable for heavy moving items such as a heavy duty boxing bag? My thoughts are, as the bag is moving the fixings might break away some on the wall material and so loosing its integrity. What do you think? Any suggestions on what I should use if not these? Cheers
@chrisperrins80822 жыл бұрын
Excellent and patient presentation. I have learnt a lot.
@chip28814 жыл бұрын
Like how you explain all features and leave no questions, solid vid
@charliesanders83313 жыл бұрын
Thanks Andy for such a clear and comprehensive video. I had a few queries as to how to use these anchors and it has answered them all.
@cobrahutch5 жыл бұрын
Hi Andy, I have to agree with other comments made, I use concrete or “Lightning bolts” these days. I once tried to hang a heavy duty tv/satellite bracket on a new extension wall using rawl bolts. I drilled into the centre of the brick to find the bricks had frogs in them, the rawl bolts would not anchor and kept spinning. Ended up having to use chemical anchors instead after drilling many holes..... Rawl bolts are ok for drilling into concrete and dense concrete block, personally I wouldn’t use them on brickwork unless I was confident the bricks were solid. Thought I would share my experience, hope it helps!
@rabri-ghewar Жыл бұрын
Thankyou sir I was fitting my pull up bars in wall and I only knew about plastic anchors These metal anchors came with the setup and i did not know how to use it. 👍🏼
@chevyimp58574 жыл бұрын
great channel.one of the best with minimal fluff...Crucial to hoover out the hole.. I normally insert with bolt fully home otherwise there is a possibility of pushing the wedge out when tapping in...
@stevenm28102 жыл бұрын
What kind of anchor would you recommend for hanging something on an exterior brick wall of a house?
@antares4443 жыл бұрын
Can I use them to put timber into brick wall which gonna be used as a support for rafters above the patio?
@marcchrys Жыл бұрын
The Screwfix site suggests a 10mm drill bit for M8 sleeve anchors and I've seen other videos suggesting 12mm?
@TOTandMom9 ай бұрын
This is a great video. I see everyone talking about using them in concrete or brick and mortar. What about drywall?
@thecatat72 жыл бұрын
Thanks for posting this! Very informative for a noob like me. Thank you very much again.
@DS-cy6mf Жыл бұрын
Great video! Will I be able to use them on cinder block to anchor a safe?
@HarrySingh-gb8xq4 жыл бұрын
Great video explaining how these bolts work, my question is; Is there a bolt with the same casing that once screwed in has a 'special' screw head which makes it hard for someone to just come along and unscrew and walk away with what it's holding to the wall. I have some railings that are bolted into a brick wall and I'm trying to make it difficult for a chancer to just unscrew and walk off with them. Thanks in advance
@Egirk3 жыл бұрын
Shear bolts ;)
@1994AustinSmith2 жыл бұрын
@@Egirk That the kind where the head is designed to shear off?
@Egirk2 жыл бұрын
@@1994AustinSmith yes
@rrsrsamsung3623 Жыл бұрын
Hi Andy. Excellent video. I tried installing some of these anchor bolts but the bolt is not catching the nut. I think my drilled hole may be deeper than the anchor bolt. Any solution or should I drill elsewhere a shorter hole. ?
@pennyy99659 ай бұрын
Would these also work in Breeze Block? If not, what would you recommend. I am wanting to install a gun safe which will be resting on the floor. Thanks.
@kstevenson35045 жыл бұрын
Thanks you explained all the aspects of this not just putting it in the concrete.
@nataliebutler2 жыл бұрын
I need to hold a long branch onto a base. The wood is very hard. Would it work for this or would you recommend something else?
@carlruss70033 ай бұрын
This is great! Can these be used on a brick fireplace hearth (thin plaster over it ) I’m not sure how thick the brick is and if it classes as a single leaf wall
@Abdul202553 жыл бұрын
Great video this is. I have a 12m rod that I need to fix to wall for a glass Juliet balcony but there is no bit for me to put the spanner on the end to tighten it’s just a full rod. Any suggestions on how I can tighten this up. Thanks.
@aadittoshen3 ай бұрын
Hey! Thanks for that clear and instructive video! Could you help me with a specific problem? I want to pour a concrete slab - incorporating such wall bolts into it - rater than drilling holes later... Once the slab is solid - I want to remove the bolts from the housing (which should stay within the slab) and reinstate them to fasten my 'load' onto the slab. Do you think this could work? Thanks in advance!
@nineth9445 жыл бұрын
If you add an extra 5mm to the depth, won't you risk the nut falling into the bottom, and the bolt and nut turning simultaneously and making no progress? I've seen M8 bolts where the nuts aren't stuck to the sleeve, but they are free if there is no bolt through them!
@sugarraydiabetes82742 жыл бұрын
Is there a better feeling than a plug or bolt tightening solid into a wall and it being level. It never gets old for me even for a simple wallplug and screw.
@illuminate062 жыл бұрын
Should my external newbuild house wall with render over brick be strong enough to fix a wall mounted pull up bar using these fittings. I'm 85kg and the pull bar takes 6 bolts?
@rogeliomedrano5553 жыл бұрын
Friend:what size of GI tubular usually use for making just one room attach to concrete by using wallbolts?tnks &keep safe...
@problemslayer3538 Жыл бұрын
What type of sleeve anchor would you use for attaching a motorycle anchor, specifically the hiplok wall anchor weighs less than 2kg i would say, to a brick wall. A reasonable heavy motorcycle chain will be going through the hiplok anchor. Would it be a drop in sleeve or expansion sleeve ?
@artursskabs395125 күн бұрын
Perfect 👌very good explanation. Now I know how to use bolts. Thanks
@timewithsopy2 жыл бұрын
great info for dummies like me. Thank you!
@DavePawson3 жыл бұрын
Useful, thanks. Question: you mention in passing 'longer bolts', e.g. to fasten a batten to a wall? How to id such rawlbolts? What's the max thickness of bracket / batten for these please? When to choose a plug vs when to choose a bolt?
@randomscience4k3 жыл бұрын
Wonderful video! Finally understand how these work. Trying to add a couple of new ceiling ikea light fixtures and I got a similar wall expansion hook bolt.
@dailydriver28252 жыл бұрын
Hi, for dot and dab walls, what spacers would you use?
@dash1645 Жыл бұрын
will this work for regular drywall?
@twinturbo52122 жыл бұрын
Should I use these for radiators into solid walls or the chunky plastic plugs that came with the rad? Thanks (I'm a geordie too)
@Idit2Gavra Жыл бұрын
Can it be used to attach semi partition to the floor?
@RKDTOO3 жыл бұрын
Will these work on a gypsum block wall?
@EThome2 жыл бұрын
Hello thank you for the idea. I bought a awning and these type of bolts came with it to hang on the wall. My wall is wood will then work on that or…. Thanks
@ConnorBrandon673 жыл бұрын
Hi there sorry to trouble you however I am looking for some advice. I am going to be building a window cannopy at the front of my house. And I have been instructed to fix some 6x2 timber to the house in order to take the weight of the cannopy and to fix it using resin and screwed rod. However as my house has wall cavities I can only insert the rods in 50mm. Should this be enough to hold the cannopy of is there any other fixing method I can use for example going through the cavity into the internal brickwork and use some other fixings?? Thanks
@jimchristakopoulos61842 жыл бұрын
Best video yet...Thank you!
@TonyMontana-os8ri3 жыл бұрын
Will they hold 6ft fencing post fit at the bottom to concrete walk or better use plastic plugs. And can I get galvanised
@rosalindbrown44233 жыл бұрын
Hi, I want to put shelving in a cupboard. The wall has just been plastered (skimmed) Behind the plaster is solid wall with bricks most likely behind this. I am inclined to mount wood (2 inch thick) and then place shelve on top. Would l need 8 inch bolts
@GARDENER423 жыл бұрын
Highly recommended for fixing gun safes to walls. Used the M10 Screwfix ones & tested with a 30" crowbar jammed down the back with no movement.
@moscowmma12794 жыл бұрын
Will them bolts handle pull up bar mounted in wall?
@findvoltage3 жыл бұрын
What size drillbit did you use and what size was the bolt ?
@rollpunch719633 жыл бұрын
can you use these on cinder block walls ?
@n33cho5 жыл бұрын
Would these be recommended to use for a commercial kitchen canopy? Weighing 75kgs. 1100mm (D) x 2480mm (W) x 500mm (H)???
@ianbird61402 жыл бұрын
Great videos! Where would I get the spacers to bridge the cavity on a dot and dab wall Many thanks
@andykopgod Жыл бұрын
This is what im looking for. Amazing, big thanks. Got 2 heavy TVs to hang and my DIY skills are crap. 💪
@WASOMAMOSES8 ай бұрын
This has been so helpful, thank you
@christophermathison12764 жыл бұрын
Hi. Thanks for the video. Presumably these would work well into a concrete ceiling too or do you think there is a better solution out there?
@xX88B88Xx3 жыл бұрын
Can you use these to hang from a concrete ceiling?
@faisalps88352 жыл бұрын
Awesome bro... I should have watched this video before i messed up an anchor bolt...
@jtoeleraj5 жыл бұрын
One thing you forgot if I am not wrong is which dril bit size to select for which size bolt. Please provide info on that. Thanks for so informative video
@tareklandoulsi17342 жыл бұрын
Are this good for an awning?
@dsgg57142 жыл бұрын
Can I use 65 mm long concrete anchors if the wall is 60mm thick?
@sircompo3 жыл бұрын
Thanks dude. That was EXACTLY the video I was hoping to find. You have a new sub 👍
@tommyharris58172 жыл бұрын
Are they suitable for breeze-block garage walls?
@PiqueBlind3r3 жыл бұрын
i need to fit a steel bracket in my garage to lock a bike upto would i be able to add ready made cement in the hole to stop the screw been unscrewed again ?
@iain.wlaird22752 жыл бұрын
If I use a 125mm x m8 bolt on a block wall to hold steel work sitting at 45 degrees. Will there be any issues using a longer bolt than say a 80mm bolt.
@byzanttine3 жыл бұрын
Thanks for the video. I was going to fix something similar to install a heavy geyser and this video was very helpful.
@idrismokhtar36212 жыл бұрын
How do you choose which size drill bit to use as I see after you've drilled the hole, the wall bolt fits into it kinda loose?
@MehmedimS2 жыл бұрын
in table shown 3:32, required drill bit writen under headline of "Drill-Ø"
@reaper060670 Жыл бұрын
I bought a pack of 25 Sleeve Anchor bolts off Amazon. They are fairly weak in their design and they're not as heavy duty as those in this video. Mine are M6 x 60mm. Would they be ok to hold metal brackets onto a concrete wall?? I want to put up brackets on my shops concrete block wall for lumber storage. Would u think they might be strong enough.
@tohirizulkifli73694 жыл бұрын
Hi Mr Gosforth. Can u tell me what is the size of wall bolt and masonry bit that u have used in this video. Anyway nice video and explanation. Tq!
@RoyAlexander4 жыл бұрын
Great thanks. Trying to hang a punchbag on a wall that's got plasterboard on top of brick. Bit of a nightmare but getting there. How tight do they go? I've got 3 in and seem to be able to tighten them and tighten them.....
@Bob_Burton6 жыл бұрын
I was waiting for the test where you test how much force is required to pull up a section of your garage floor :-)
@neilrobinson81014 жыл бұрын
Could this type of fitting present problems in old bricks that seems brittle?
@GosforthHandyman4 жыл бұрын
If they're surrounded by other bricks you're normally fine but these can *easily* split bricks if they're at the edge of a wall for example. 👍