Graphtec CE7000-60 Basics For Perforated Sticker Cutting

[@AnZ85]

So it's basically like dashline cutting. For those normal cheap cutters.

[@stickerhoggz]

So on this you would want to do #2 so that you don't have to scroll so much on the vinyl there. It's how i do it. Just keeps it closer to the crop marks.

[@mikesstickers]

Are you talking about where it says Roll 2 - Current Position

[@stickerhoggz]

@@mikesstickers Yes, that is correct.

[@mikesstickers]

@@stickerhoggz I’ll give it a try. Thanks

[@onestoppromo]

What system are you using to print on the vinyl?

[@mikesstickers]

@@onestoppromo I’m using a Roland BN-20a for my printer.

[@desertgardencollective]

What vinyl do you print on for stickers? I have a roland bn20a myself

[@Lucky7Graphix]

Does this work for the CE6000-60?

[@518pressandgo2]

Where did you order your 60 degree blades!? Plz Ty!

[@mikesstickers]

I ordered this kit just for the 60 degree blades. I could not find a set of just 60 degrees by itself. CB09 CB09U Graphtec Blade Holder with 15pcs Vinyl Cutter Plotter Cutting Blades 30/45/ 60 Degree a.co/d/9DJvPyH

[@chrisfortin8549]

@@mikesstickersBe wary of aftermarket stuff.. I have a pile of 60 deg blades I wont use anymore and aftermarket blade holder.. I was getting horrible cuts, went back to graphtec and got a new 60 deg blade and blue tip holder and back to mint.. just saying if you have an issue you cant find.. this where the solution may be!

[@mikesstickers]

@@chrisfortin8549 good info. Thanks

[@Justlawl]

Hi can you do a guide on setting up the step and repeat on the document as I am putting in illustrator, copying and pasting but the cut line and image stays in one layer rather than seperate cut line and image thanks

[@mikesstickers]

Yes I will work on that.

[@Justlawl]

@@mikesstickers thank you

[@Justlawl]

@mikesstickers And the best way to maximise stickers inside the scan marks etc all will be helpful 😀

[@mikesstickers]

Here you go. See if this one helps. substance.com/products/icon-pm-2755

[@ChrissRollex]

Sorry, may I inquire about something? I noticed the blade number "cb09u+0" on your screen. Are these blades not the standard factory-supplied ones that come with the Cutter plotter? When I received my Graphtec CE 7000, it came with blades that have the same code 'cb09u+0', and the manufacturer tells me that they are 45 degrees. By the way, thanks for your tutorial video! 🤗🤗🤗

[@mikesstickers]

I’m using 60 degree blades for the perf cuts & the 45 degree blade for contour cuts. The 60 degree blades & holder are a cheap $15 kit from Amazon.

[@ChrissRollex]

Oh, that's interesting! Are you working with blades of 1.5mm or 0.9mm thickness? My supplier recommended purchasing the 'red cap' blade holder with 1.5mm/60^ 'cb15u-k30-5' blades. As I'm relatively new to the realm of cutting plotters and vinyls, I'm unsure if these blades are suitable for my needs. Hence, I'm seeking your advice on this matter.@@mikesstickers

[@mikesstickers]

@@ChrissRollex these are the ones I’m using. CB09 CB09U Graphtec Blade Holder with 15pcs Vinyl Cutter Plotter Cutting Blades 30/45/ 60 Degree

[@majidsignshop4903]

😍😍

[@Statikleoscamming]

mine is doing the same thing vinyl doesn't lay flat it bowes causing the blade too glid transitioning thru the cuts did u ever fix that problem i thought this would have a suction thing that held the vynil down like the bn20

[@mikesstickers]

@@Statikleoscamming yes, someone told me about a setting that pulls the blade up off the material before moving to the next design. I don’t remember exactly how to do it but someone on the Facebook group told me how to do it. In addition to that I also found a 3D printed guide that holds the material flat in the middle of the cutter. It’s a very simple device that someone sells on Etsy. I’ll see if I can find it.

[@mikesstickers]

@@Statikleoscamming here is the 3D printed push arm. For my 24” cutter I only needed 1 of these to add to the middle. I think this device helps the accuracy of the cuts in general. The real fix for the scratching of the vinyl was the setting to raise the blade between cuts. www.etsy.com/listing/1240449602/graphtec-push-arm-v21-new-and-improved

[@aliciagolden8258]

👊 "promosm"