He decidido hacer una revisión al motor con 600 km, el engranaje de naylon estaba bien lubricado de fábrica, he aprovechado para engrasarlo y quedar más tranquilo.
Пікірлер: 110
@tombrenner44185 жыл бұрын
I finished my repair and tear down. Didn’t think I could do it. Watched several videos of different problems.Take lots of pictures and take note,even if it’s looks silly,putting it all back together was easy.Get the proper tools is a must.I used the mobile 28 because of the properties.I have the same motor and my core body was replaced.I greased mine and am totally blown away as to how quite it is now. At high speed my tires make more noise. In the lower speeds it’s quite.Before the motor gave off a high pitched whine to which I can now say lack of grease.The first thing I noticed was getting better top speed 43 to 50 km/hr.Been out twice now.I needed to tighten up the crank arm because of cracking out from to loose.This time went over and used blue lock tightener.My ride went well and didn’t notice the same problem. Ride safe folks.
@portnuefflyer4 жыл бұрын
Pretty profound music, I didn't realize taking the motor was such a serious thing! Actually, I liked it, set the mood just right.
@e-mtbbbs14873 жыл бұрын
Thank you very much for your pleasant comment, a way of helping us
@tombrenner44185 жыл бұрын
May 22/2019. I fallowed this method and greased everywhere you did and thank you for your idea. How my bike is supper quite and you can hear the motor but a like low pitch whirling num.I showed it to a friend with more knowledge and he thought it sounded like what a electric motor should sound.I also get a faster km/per hr.As of this date I have ride 200 km and have no problem.Thanks again,ride safe.
@colincroft27044 жыл бұрын
Great video, thank you. One tip: make sure your nylon gear is not 'upside down' before re-inserting/installing. The sides look identical, but you'll see the obvious indent where your snap ring will go back on. Much easier to do BEFORE you have all that grease on there :)
@e-mtbbbs14873 жыл бұрын
THANKS A LOT
@markreisdorf58604 жыл бұрын
Great video! It showed the whole process very clearly and showed a very simple quick and useful upgrade.
@user-gt5jp5jy2b7 жыл бұрын
excellent job 👍 I like the music and no talking and Mobil Grease 28 is the right choice.
@portnuefflyer4 жыл бұрын
I love it when the cir clip goes flying off, (never to be seen again no doubt) right at 2:44 in, that's realistic right there.
@e-mtbbbs14874 жыл бұрын
If I found him by my side
@gedofgont10063 жыл бұрын
@@e-mtbbbs1487 Did you dismantle the whole thing and reinstall the missing screws from the nylon gear cover plate?🤷♂️
@MM-kq7eu6 жыл бұрын
This video is forcing me to acknowledge my freaking love of electric bikes. The bafang bbshd and this music is too much for me. .....Will be needing to go ball my eyes out for a while!!!!
@rossg93632 жыл бұрын
The colour of the original white silicon grease inside at 4.17 looks in excellent condition! I would have put it back together as is, that mobilegrease 28 is not dielectric where as the original white silicone grease is dielectric.. i found your video pretty awesome! i enjoyed seeing the full teardown of the motor compartment👍💪
@e-mtbbbs14872 жыл бұрын
☺
@mani-00 Жыл бұрын
why would you need a dielctric grease for the nylon gear?
@andy-the-gardener4 жыл бұрын
I can tell this is is a person who really cares for their stuff.
@danshady093 жыл бұрын
seriously? the guy looked like hes never done anything like this before
@billmarsh19713 жыл бұрын
@@danshady09 he was shaking while reassembling the beastie...
@andi42813 жыл бұрын
That's quiet! 👍👍
@CrIMiN8l6 жыл бұрын
how has it been since the mobile greaseing?
@danyforbach90576 жыл бұрын
anglais , no comment .... good taf , francais , pas de commentaire .... du bon taf
@whiteshadow21323 жыл бұрын
Excellent
@MeysamShojaeeNejad3 жыл бұрын
Shouldn't a white lithium grease be used for the nylon?
@Sanwizard12 жыл бұрын
Nice music!
@darshanpansuriya28136 жыл бұрын
what is the size of gear means pitch,module,no.of teeth,width,height?
@Nizacx7 жыл бұрын
you didn't put the screws back on the greasing wheel thingy.. rip.
@e-mtbbbs14877 жыл бұрын
If after the recording I put them
@tombrenner44185 жыл бұрын
I have the HD and it’s hard to get those back in. Although the greasing is necessary as I took mine apart because it was virtually dry. I need to replace the
@e-mtbbbs14875 жыл бұрын
It's better to prevent, I'm sorry
@navigator_0712 жыл бұрын
Very unusual choice of music for the tutorial but it's OK, it fits. It may even become a trend instead of the usual, worn-out tra-la-la musical backgrounds Anyway, good video.
@rodolfobaliga75772 жыл бұрын
Where to buy the new nylon gear in case it will damaged.
@okotoood1133 Жыл бұрын
what gease to use ?
@andresmejia77414 жыл бұрын
El sistema se ve rudimentario y de mala calidad ?Cual es tu opinion ?.He estado pensando en comprar uno , pero un poco dudoso ! Gracias por el video !
@TK-OK4 жыл бұрын
Only 745 miles ? Or is it 12,000
@MrSoggyjocks4 жыл бұрын
My bbshd seems to run fine, but when I pedal I get a creaking noise. Doesn't happen when I just use the throttle. I think something needs greasing internally, but I am not sure. I hve heard there are some bearings inside which may need a lube. If anyone has any ideas. I have checked the pedals are tight and that the unit has been mounted solidly, nothings loose
@e-mtbbbs14874 жыл бұрын
you have to be cautious and prevent
@timdouglass64915 жыл бұрын
Is the plumbers tape necessary to hold the motor in place?
@e-mtbbbs14875 жыл бұрын
Maybe I can help
@MrSoggyjocks4 жыл бұрын
Mine slipped a fair bit till I ended up using some long zip ties and some thread lock.
@RicSil693 жыл бұрын
Hi what gear oil would you uae for 350w rich bit geared rear hub motor. Mine requires me to put in 35ml of gear oil after 3 months of me uaing it. But what gear oil do i need?? Many thnks
@e-mtbbbs14873 жыл бұрын
yo he Puesto LGMT 2/0,4 SKF Bearing Grease
@tvbrasil80 Жыл бұрын
Que tipo de grasa recomiendas bro?
@Samson-EC3 жыл бұрын
I have read several snippets on whether to lube or not lube nylon gears. Also that mob 28 is the way to go. Your thoughts and whether or not o-ring lube is OK to use on them...thks..jc
@e-mtbbbs14873 жыл бұрын
I have not had any problems, the experience has been very positive. Very quiet engine
@rlni21103 жыл бұрын
"Because lithium grease is petroleum based, it's not recommended for use around plastics and rubber where it'll cause these to prematurely fail. ... Silicone grease, on the other hand, works better in low temperature, low stress applications around plastics and rubber." Mobil better used on those steel secondary gears.
@e-mtbbbs14873 жыл бұрын
thank you
@marcolucarelli51653 жыл бұрын
21890km in 4 years without maintenance at the motor. Bafang 36v 250w speedlimit off
@e-mtbbbs14873 жыл бұрын
Genial
@e-mtbbbs14873 жыл бұрын
👍yo he preferido hacer el mantenimiento antes por precaución
@johnmarklucing71064 жыл бұрын
is the grease good to protect yhe plastic gear,?
@e-mtbbbs14874 жыл бұрын
if I read it in an article that advised
@tombrenner44185 жыл бұрын
I think after watching this,after I get the tools,give it go,it’s good that we the rider can brake it down and fix it ourselves.Its the order of the washers is what confuses me. I wished the there was a list of order to return.
@olegpetelevitch44434 жыл бұрын
I have had mine for 6 months store built dualy 27.5 . Is it normal for the screws to be loose in certain places ? As i don,t know 1st E bike ? And for some reason every 3 4 rides i have to tighten a few bolts screws ! Thank you top instructional as i do all my self learning this motor.
@e-mtbbbs14874 жыл бұрын
It is not normal but usually occurs
@olegpetelevitch44434 жыл бұрын
Cool thank you ! I see in the blogs its a common problem . All good, have the tools just not the knowledge .
@billmarsh19713 жыл бұрын
@@olegpetelevitch4443 get some loctite blue thread lock on the offending bolts, it'll stop them from slackening and falling out
@bluebird1422 Жыл бұрын
any update?
@ClaudioA4 жыл бұрын
Buen vídeo.... Mi motor dejo de funcionar después de una gran lluvia. tengo batería... la cargue y medí con tester. Pero nada enciende... el display no pasa nada. Todo esta muerto.... que podrá ser??? Tienes alguna idea.
@marcthebrush4 жыл бұрын
It can be the controller inside the motor i had to replace it aswell.
@ClaudioA4 жыл бұрын
@@marcthebrush Thanks for your answer. I changed the controller. Also replace a ceramic fuse in the red power cord. Then everything worked very well.
@ricardorodrigues35083 жыл бұрын
Probably water infiltration burned your controler, take it out and check the components, could be just a resistor burned or similar, and a cwry easy and cheap job to replace
@frantxu19692 жыл бұрын
pues creo que no pusiste los tornillos de la tapa del engranaje de teflón...
@kakekikoku4634 жыл бұрын
Hola, han pasado 2 años desde este vídeo, qué tal sigue funcionando el motor? ¿Qué tal con el paso del tiempo?
@e-mtbbbs14874 жыл бұрын
Hola compañero, continua perfectamente, voy a comprar otro igual para mi pareja, le tiene otro amigo y encantando también. saluddos
@kakekikoku4634 жыл бұрын
@@e-mtbbbs1487 Gracias, por la respuesta, perdona por preguntar más pero, ¿qué motor recomiendas? ¿Y compras todo el kit completo o por partes? Y no me queda muy claro los sensores que van a las manetas de freno si se pueden adaptar a todos los sistemas. También veo un poco inestable el sistema de sujeción enla caja de pedalier, veo que no usa el mecanizado propio si no que es un eje pasante con contratuerca, no se si con el paso del tiempo da holguras Gracias
@e-mtbbbs14874 жыл бұрын
@@kakekikoku463 yo tengo el 1000w quite el sensor a una maneta y lo adapte al freno trasero. el pedalier fenomenal sin problema, aunque lo asegure con una abrazadera
@marcthebrush4 жыл бұрын
I keep falling a sleep.
@mansooreshragh6 жыл бұрын
Mixing mob 28 and lithium grease doesn't look a good idea! chemical compounds property changes when you mix them.
@offgriddreaming54036 жыл бұрын
I did wonder about that. Still should be better than not at all
@GauisHelenaMohaim6 жыл бұрын
Half the amount of grease would have bin sufficient imho. 😉
@akoakko66737 жыл бұрын
Did you have problems with the motor moving downwards at the beginning? Your bottom bracket looks pretty worn out from the side, and you mounted the steel plate the other way round, that's why I'm asking. I'm currently abount to mount a BBSHD on my bike myself, and I'm a bit concerned if the stock assembly is enough to hold the engine properly. - Though I haven't really read about these problems so far.
@e-mtbbbs14877 жыл бұрын
At first it moved with the use, I decided to place a sucker and solve the pro
@e-mtbbbs14877 жыл бұрын
at the moment I do not have any problem the wear was produced by a chain exit
@HermieDaddy5 жыл бұрын
Forgot inner screws
@user-ct6lx9rw9o4 жыл бұрын
Что за смазка? 👍
@neilcopeland44113 жыл бұрын
Never put back the posidrive screws on the cover plate to the nylon gear
@gedofgont10063 жыл бұрын
I noticed that! This guy must love motor tear downs, cos he's gonna be doing a whole lot of 'em!😖
Emplea siempre para el Nylon grasa de Litio Blanca que no lleve compuestos derivados del petróleo y con un bastoncito de los oidos se la aplicas poco a poco. Las grasas derivadas del petróleo se comen el plástico del Nylon por reacción quimica como se puede ver en este video: kzbin.info/www/bejne/oJSzhaGYfKafaNU
@n.a.37342 жыл бұрын
👏👏👌👌👍🤑🤑
@jaciks4 жыл бұрын
i recommend drill hole for oil nipple.
@3dkiller6 жыл бұрын
man i am doing 20000km on my bbs02 and still going strong. No extra greasing needed !.
@e-mtbbbs14876 жыл бұрын
It seems to me gemial, I after having visualized several cases of engines destroyed by lack of fat I decided to prevent, since the fafricante does not guarantee nor specifies, considering that it is not the same to walk by asphalted road that by mountain. regards
@e-mtbbbs14876 жыл бұрын
It is not an obligation, it is information to show that it is easy to do it
@3dkiller6 жыл бұрын
its good to prevent things i agree on that, my motor is now at 36000 km. Still solid :)
@3dkiller6 жыл бұрын
My bbs02 750w 52v is now at 36000km still doing fine no problems at all.
@bodoruhle2664 жыл бұрын
Hallo! Danke fürs Video. Von Servise-Technikern hört man immer, die Getriebeteile sind wartungsfrei, fetten nicht nötig! In Deinem Video konnte ich sehen, dass Du beim Zusammenbau den Flanschdeckel nicht wieder mit den Schrauben angeschraubt hast, stört das den Motorantrieb?
@e-mtbbbs14874 жыл бұрын
:) Es war ein Fehler bei der Aufnahme, aber ich habe es später gemacht
@recordingmastering Жыл бұрын
Is Mobil1 Synthetic as good as Mobil 28 (is is the same stuff ?)
@olegpetelevitch44434 жыл бұрын
Don,t like the shop i bought my bike did not honor warranty after 4 months took 3 reports to consumer fairs ! Finally fixed it faulty front axle accelerator didn't work with pedelec ! Im 50 treated like shit ! Bought most the tools now ,i am learning myself !
@frantxu19692 жыл бұрын
4min.50seg
@roncooke21885 жыл бұрын
Great with volume off
@ricardorodrigues35083 жыл бұрын
You dont need to take the nylon gear out to grease it, unless you done over 10000km and need to clear the residues on it, otherwise just apply grease via the hole
@rhkgerhkge41192 жыл бұрын
Threw which hole is there
@rossg93632 жыл бұрын
What hole is that you know about?
@ricardorodrigues35082 жыл бұрын
@@rossg9363 when the stactor is removed the nylon gear is exposed in the middle, just get some grease on your finger and stick it inside to paste it on the nylon gear, that is more than enough after 1200km, as said, about after 5000 or 10000km you should inspect the nylon gear, clean old grease and possiblem residues of dirt and parts wareout in it, but i've seen bbhds with 20000km or more, never cleaned before and they were fine, depends a lot if you ride in rain mud or dirt too, bikes doing just tarmac dont need that much maintenance as bikes doing trails. BTW the center hole is seen at 2:12
@rossg93632 жыл бұрын
@@ricardorodrigues3508 ah ok thanks i thought you where referring to a exterior hidie hole somewhere, thanks mate.
@ethanschneider24223 жыл бұрын
Looks like ketchup sauce
@chrislast5470 Жыл бұрын
Too late now he forgot the screws !!
@e-mtbbbs1487 Жыл бұрын
😝 solo en el video
@Longsim373 жыл бұрын
Des
@mous240003 жыл бұрын
Boor 8000km und warum wartetet ihr das ich mach noch mal 5000km alls nur scho
@user-gt5jp5jy2b7 жыл бұрын
excellent job 👍 I like the music and no talking and Mobil Grease 28 is the right choice.
@e-mtbbbs14877 жыл бұрын
Thank you very much for your opinion
@ginojens5 жыл бұрын
Mobil Grease 28 is the wrong choice for nylon. It is only good for 2:th gear in metall.
@otablott77795 жыл бұрын
ginojens hi ginojens, what would be a better grease for the nylon gear?