New Vintage Air install on a frame up square body build!

[@henrytaylor3049]

I really love the cup holders frenched into the seat👍. The argile in the engine bay and the seat is pretty sweet too...❄️ Truck.

[@red93yj]

dude, that truck is amazing!!

[@ericdavis7002]

Great information! Love the truck! Color combo!

[@NaztyNate]

THANK YOU for such a great install video!!!!!

[@bobdaily836]

nice job, thanks for the updates of what needs to be done

[@Flyguy843]

Sweet setup. I’m planning to do my truck soon.

[@billlloyd9755]

Nice pickm up truck 😊

[@LaMalditaC10]

That’s a really nice truck. Congratulations 💪🏻💪🏻💪🏻

[@cwmotorsports4497]

Thanks for the video!!! Very informative.

[@eddiedominguez7055]

Really nice job

[@robertoherrera9793]

Thanks!

[@yourboij82]

Nice one! 👍🏾

[@pablotonche5780]

Awesome video. What’s the belt part # if you don’t mind sharing. Ty

[@saltyoperator7435]

I wanna know the part number on that cat! Bc I need to order one meow!

[@gbertostorage1575]

I need this

[@NDB390]

What high mount bracket did you use? And was your truck a factory air or non factory. I have a non factory and finding that it’s a lot more money for a non A/C truck. If the main difference is inside duct work then can a guy just pull duct work from a donor and save some money?

[@NDB390]

Hello. I like that color combo. Question: Have you had any issues with the condensers with the Vintage Air setups? I need to buy a kit but seen a few things that people are saying they have had issues with the condensers being undersized and they have intermittent cooling issues and swapped them to bigger ones and haven’t had the issues since.

[@GreaseMonkeyTV]

Never a single issue. Blows colder than the other two brands I’ve used.

[@michaelhood1291]

Fantastic video! 🇺🇸💪🏼 Can you tell me how much real life time this Vintage Air install takes?

[@GreaseMonkeyTV]

Probably 4-5 hrs on a completed truck.

[@billyconnell5628]

bad ass truck sir how did u go about wiring the ac control to the idle air controller or ecm to make motor idle up when ac is on?

[@GreaseMonkeyTV]

You can send a signal to the PCM via a designated wire in most aftermarket harnesses.

[@UpinSmokeBarBQ]

What equipment are you using for to record the video? And your truck is awesome

[@GreaseMonkeyTV]

iPhone 12, GoPro 9, MacBook iMovie.

[@martinolivas319]

I’m having issues finding why my factory climate control system constantly pulls in air from the engine bay. My Exaust is leak free, but at stop lights I pull in Exaust from the surrounding vehicles. Any advice would help

[@GreaseMonkeyTV]

Turning your air to recirculate uses only the interior air.

[@handyrandysgarage6929]

I have close to the same set up as you. I’m having a issue of the idle rpm dropping so low sometimes at a stop light that it kills the engine when the ac clutch cycles. Did you do anything to bump up the idle when it cycles?

[@GreaseMonkeyTV]

Your tuner should be able to fix that.

[@CaseyDillon-os4kd]

What did you do to make the defrost vents fit? I don’t have any factory holes to screw to although my truck is factory air. I could also not get my u-nots to fit. Thanks in advance. Great video and truck as well!

[@GreaseMonkeyTV]

Interesting. Your factory air truck doesn’t have the defrost mounting holes?

[@CaseyDillon-os4kd]

No sure doesn’t! It is a factory air truck as I removed the factory AC. Thank you for your reply. Sent email to Vintage AC. Every other video I watched everyone just screwed them into place.

[@benjaminnewsom9193]

What gauges are you running on this build? I’m like those a lot

[@GreaseMonkeyTV]

NVU

[@ParadiseOnOctane]

Great work,Which vintage air kit are you using??💪

[@baderalsaho2912]

please can you make it a video to explain how to read and working ecu with o2 sensor in your car with knock sensors my truck is swap ls engine not read it I have problems with low voltage knock sensors bank 1 bank 2 and please anyone one help? With that issue

[@GreaseMonkeyTV]

Probably need to seek out a good mechanic in your area.

[@seanjordan4485]

What gauges did you use?

[@apluspooldesigninc6122]

what size are those wheels?

[@baldheadatl7902]

What kinda engine 5.3 or 6.2

[@GreaseMonkeyTV]

5.3

[@pablotonche5780]

What belt did u use ???

[@GreaseMonkeyTV]

Can’t remember. Tried about 3

[@crsmith56]

Do you dare to give us a complete price list of what it cost to build?

[@GreaseMonkeyTV]

😂 not a chance.

[@crsmith56]

GreaseMonkeyTV Don't blame you! Thank you for the info and inspiration on the build. Awesome C10!

[@JeLifeCoach]

@@crsmith56 Chassis 23K plus, motor and trans (20k), VA kit (2200), wheels and tires (3k), sound system (2-3K), interior carpet and dress (2200), chrome bumpers and trim (1-2K), finding a project truck (8-15K), paint (who knows probably 20K). I’d say well over 70K.

[@jasonfarnsworth5880]

Probably more like 85