Grid connected inverter design in Matlab Grid tied inverter design in Matlab Şebeke etkileşimli inverter tasarımı Şebeke bağlantılı inverter tasarımı how to synchronize pll grid to inverter in matlab
Пікірлер: 106
@hocho72544 жыл бұрын
For simplicity we can use BREAKER with external control instead of Anti-Parallel connected switches: Thank you sir for your great contribution in the society
@shahkhan1104 жыл бұрын
Thanks alot for these valuable videos. This is very helpful for grad students doing masters or PhD. Looking forward for other videos related to smartgrids, Wind, PV, etc.
@nakiguler4 жыл бұрын
I am glad to hear such a response. I am so much busy. When I have time I will share a new one.
@elijahturatsinze15764 жыл бұрын
Hello, thank you so much for the video but I dont understand the role of parallel connection . May you please tell me what is it?
@berktuncer4773 жыл бұрын
Naki hocam merhaba, yine ben :D burada faz açısını kontrol ediyoruz ya bu neyin faz açısı oluyor, referans sinyalin açısı mı oluyor. Hocam bir de bu faz kayması kontrol yöntemi olarak mı geçiyor.
@nakiguler3 жыл бұрын
Merhaba Berk, evet referans sinyalin faz açısı oluyor. Burada kontrolden ziyade faz açısı ve modülasyon indeksinin etkisini göstermek istemiştim. O yüzden feedback almadan yaptım.
@berktuncer4773 жыл бұрын
@@nakiguler Anladım hocam teşekkürler.
@ahs47713844 жыл бұрын
Thanks for your great contribution
@nakiguler4 жыл бұрын
Thanks for your interest.
@udayakiranpadmapadacharyas23063 жыл бұрын
Its very helpful. Thank you
@shuvankarpodder13514 жыл бұрын
Hello Sir, how can I select the values of the filter inductors and capacitors? Would you kindly suggest a text or tutorial please?
@Abul.Munjer6 жыл бұрын
sir, i have designed a simulink model of MMC for capacitor voltage balancing . when i connect it to the grid as you uploaded, before connecting it works as natural multilevel converter, load current was same but after connecting it to grid, converter takes huge current from the grid. what may be the possible causes for that? thanks in advance.
@AbbasAli-ho2zs5 жыл бұрын
Thanks Mate, you have showed all steps how to get to the end point. Sir, have you published this paper on any website ? If so, I would like to use it as a reference!
@nakiguler5 жыл бұрын
Hi, My 3 paper published about inverters as follows. I am writing a paper about inverters, but I did not submit yet. 1-Naki Güler, Erdal Irmak, Halil Gör, Erol Kurt (2017). "An Inverter Design for A New Permanent Magnet Synchronous Generator". International Journal of Hydrogen Energy (SCI), Volume 42, Issue 28, pp. 17713-17722, July 2017., 2-Guler Naki, Irmak Erdal (2019). Nötr Kenetlemeli Eviriciler için Çok Giriş - Çok Çıkışlı DA-DA Çevirici Tasarımı ve Kontrolü. Gazi Üniversitesi Fen Bilimleri Dergisi Part C: Tasarım ve Teknoloji, 7(49-62).(Turkish) 3-Erdal Irmak, Naki Güler, 2018. Model Predictive Control of Grid-Tied Three-Level Neutral Point Clamped Inverter Integrated with a Double Layer Multi-Input Single-Output DC/DC Converter, IEEE 12th International Conference on Compatibility, Power Electronics and Power Engineering~IEEE CPE-POWERENG'2018, Doha, Qatar, 10-12 April 2018.
@gudipatimaheswari68553 жыл бұрын
@@nakiguler sir are you published this paper now??
@gudipatimaheswari68553 жыл бұрын
@@nakiguler I want to take reference now??
@nakiguler3 жыл бұрын
@@gudipatimaheswari6855 yes these are published.
@abhijeetshakhawar94494 жыл бұрын
Hello sir This is really good video Could you please make video on cell balancing of BMS in EVs
@nakiguler4 жыл бұрын
Hello, thanks for your interest. Cell balancing is a deep issue for battery management. I have no experience with cell balancing. Sorry.
@deepankarraturi10236 жыл бұрын
Nice work :) ...... can you please suggest some papers regarding your simulation?
@nakiguler6 жыл бұрын
You can find more paper for grid connected inverter model. My conference paper will be published in next month. You can find paper name and other details in my official web site. www.websitem.gazi.edu.tr/site/gulern/academic
@malihashah19777 жыл бұрын
Since LCL filter is deigned & all method is clear & quick.How will be three phase bridge connected to filter?
@nakiguler7 жыл бұрын
Thanks, As soon as, I will upload a three phase grid tied inverter video.
@nakiguler7 жыл бұрын
I uploaded three phase grid tied inverter. You can find link in below. kzbin.info/www/bejne/oHqYZHSsqJuFkJo
@Yah5414 жыл бұрын
Hi thank you for the video, can you please tell me what is the name of control method used in this video ?
@nasimahmed31134 жыл бұрын
I actually done every thing of this video and try to simulate in Matlab . the only problem is that inverter current and grid current are 180 shifted , not sharing load like videos . kindly help me if there any silly mistake ? Thanks in advance
@hadla564 жыл бұрын
At 22:25 You wrote: igrid_max=-6A Does it mean that the inverter is now supply 6A to the Grid?
@nakiguler4 жыл бұрын
Yes, because power direction is opposite.
@hadla564 жыл бұрын
@@nakiguler Thank You
@narasimhaprasadtulasi75396 жыл бұрын
sorry, I got my mistake ,given phase shift at sine in function as wrong ,now i am getting well..... Thanks alot sir
@nakiguler6 жыл бұрын
Ok
@basilmathew97625 жыл бұрын
My grid and inverter current waveform are almost 180 shifted . What could be the issue ?
@nakiguler5 жыл бұрын
It's possible because when you transfer to power from inverter to grid, it should have a phase angle. Actually, it shows, your system transfer the current without reactive. Current direction should be opposite. It's normal.
@basilmathew97625 жыл бұрын
@@nakiguler OK. Thank you
@nasimahmed31134 жыл бұрын
@@nakiguler Sir kindly explain little more please . I have got same issue of 180 shifted current waveform
@kishorekumar-pe7mj7 жыл бұрын
instead DC power we can use solar energy sir???we can attain the same output ya??
@nakiguler7 жыл бұрын
kishore kumar yes you can use solar panel as an input source.
@kishorekumar-pe7mj7 жыл бұрын
Naki GÜLER ...sir I have used but current in inverter showing around 200amps..I don't no why???I have changed the input values of PV panel,even though I am getting 200amps...very confusion... Please help me regarding this sir...my mail id: kishore8192@ gmail.com
@asivesydney65606 жыл бұрын
Good day sir. how do you generate a fault into the grid i.e distorted voltages , unbalanced loading ?
@alejandraprada61194 жыл бұрын
Hi! thank u so much for the video Dr. Guler, how would simulation an single-phase inverter off-grid?
@nakiguler4 жыл бұрын
Hi, please check my videos. I explained for three-phase inverter. You may convert it to single phase.
@shubhamtiwari68165 жыл бұрын
Sir, your videos are very helpful. Sir kindly please upload micro grid model in which battery connected to micro grid
@nakiguler5 жыл бұрын
Thanks, I will upload some videos in next month.
@shubhamtiwari68165 жыл бұрын
@@nakiguler thanks sir
@nakiguler5 жыл бұрын
Shubham Tiwari, I share a video for battery operation modes kzbin.info/www/bejne/rYTbhaOnqN5jiMk
@suryanshpandey9529 Жыл бұрын
Can you provide the mathematics for getting the values of inductors and capacitors
@dogukanyaman79044 жыл бұрын
Naki Bey iyi günler,projem için bu video çok önemli ve bir türlü matlab function'ın kodunu doğru yazamıyorum hata veriyor hep yardımcı olabilirseniz çok memnun olurum.Size ulaşabileceğim bir yer var mı?
@nakiguler4 жыл бұрын
İyi günler, bu videodaki kodu aşağıda bulabilirsiniz. Researchgate yada aşağıdaki resmi websitesinde yer alan mail adresinden ulaşabilirsiniz. dialup-06.gazi.edu.tr/site/gulern/contact function a = fcn(x,ma,shift) shift_k=shift*pi/180; a = (ma*(sin((x)+shift_k)));
@hocho72544 жыл бұрын
Sir, after setting phase shift 2 when I close or set 1 to parrele swich than I am not getting Igrid and Iref waveform as its your ......however before this operation everything is as you are getting? what could be the possible reasons?. and what is to be set sample time at scope: -1 is by default I am using Matlab2018a
@nakiguler4 жыл бұрын
If you select the phase shift as 2, the inverter voltage may not synchronize to the grid. Please check the Matlab function block codes. Did you convert degree to rad/s? If you select the sampling time as "-1", it will be equal to the base sampling time of simulation.
@hocho72544 жыл бұрын
@@nakiguler Thank you sir, identified and fixed the issue. However, for synchronisation it is necessary to have same phase of Vgrid,Vinv ,Iinv and Igrid ???
@narasimhaprasadtulasi75396 жыл бұрын
by changing phase angle ,current phase is adjusting when parallel switch is zero ,but when we make parallel as 1 ,currents ig and i_inv both are looking like staircase ramp signals increasing in opposite directions continuously ,but if i put phase angle as zero, even in parallel 1 state(after conn grid) i am getting waveform magnitudes of grid load inv as you said at last in video please help me where i made mistake sir.
@nuraziemahazmiali89907 жыл бұрын
the inverter that connected to the grid is single phase only right? how to connect three phase inverter with grid?
@nakiguler7 жыл бұрын
As soon as, I will upload a three phase grid tied inverter video.
@nuraziemahazmiali89907 жыл бұрын
ohh thank you so much . i really excited to learn that sir
@sudhirnikam66735 жыл бұрын
Hi sir can you please explain what is step by step operation and how we get proper waveforms
@nimeshidabare75846 жыл бұрын
Hi ! I dont get the expected results when the parallel connection is enabled.The grid current and the inveter current at an instant adds upto zero.What might the reason be ? ..Thank you.
@nakiguler6 жыл бұрын
Hi. You should check somethings between grid and inverter output waveform. Especially three parameter important, phase angle should be equal, inverter and grid voltages should be equal and phase - neutral connections should be checked.
@nimeshidabare75846 жыл бұрын
Naki GÜLER thank you
@nasimahmed31134 жыл бұрын
I have same problem . Kindly explain how you solve this problem ?
@gudipatimaheswari68553 жыл бұрын
Sir how can control active power by controlling phase shift angle
@bodialitv57974 жыл бұрын
Hello.. Why you put bridgr thyristors?
@ngilyangtagia86675 жыл бұрын
Sir I need ur help to design wind turbine emulator for a microgrid simulink
@khanhbao79903 жыл бұрын
Why use a Matlab function and not a current controller?
@along1211396 жыл бұрын
sir do u know how to design grid connected inverter using proportional resonant as feedback?
@nakiguler6 жыл бұрын
+norAlone, I don’t know.
@along1211396 жыл бұрын
okay thanks
@nareshyella91187 жыл бұрын
sir any material is available to find how current varies with phase and current sharing between grid and inverter
@nakiguler7 жыл бұрын
I don't share any material but, You can seen in the video (at 20:20), relationship between phase angle, modulation index and power.
@jodisetiawan28694 жыл бұрын
Sir, is there DC parameters to monitoring?
@nakiguler4 жыл бұрын
What do you mean with DC parameters? Current and voltage? You may see all the parameters with scope.
@saiakhileshsanaboyina35666 жыл бұрын
sir, can u provide control strategy for single phase grid connected inverter
@nakiguler6 жыл бұрын
Inverter type not important for main Power control structure. Only number of switch is changing and You should design your control strategy for phase shift and modulation index control.
@GreeenSwag4 жыл бұрын
does this utilize, a boost converter and then half bridge rectification ?
@nakiguler4 жыл бұрын
andrew greene, it is a single-phase grid-connected inverter. Thyristors are used as grid connection breakers.
@GreeenSwag4 жыл бұрын
@@nakiguler can you assist with the design of dc boost converter and single phase inverter together in closed loop
@nakiguler4 жыл бұрын
andrew greene, you may find boost converter and inverter examples in my videos. I shared some control parts for inverters. You can adapt it to your model. If you have a problem, please let me know.
@GreeenSwag4 жыл бұрын
@@nakiguler Hey thanks a lot. I am trying to combine the two >.>
@nakiguler4 жыл бұрын
Ok 👍
@frozennova6114 жыл бұрын
Sir i want to contact you directly. Want to ask something and need explanation for those things. Would appreciate it.
@nakiguler4 жыл бұрын
This my official website, you can find my email here: dialup-06.gazi.edu.tr/site/gulern/posts/view/id/139133 or you may contact on Researchgate.
@pankajymca6 жыл бұрын
there is some problem in PLL when i click on run errors: Output port 1 of 'grid_example/PLL' is not connected. and second one is in matlab function : function a = fcn(x,ma,shift) %#codegen shift k =shift*pi/180 ; %convert degree to rad a=(ma*sin((x)+shift(k))); %refrence voltage
@basilmathew97625 жыл бұрын
Regarding the matlab function , scpit file path and your simulink model should be on the same path .
@gudipatimaheswari68553 жыл бұрын
yes..same.. iam getting error..how can i clear it??
@pankajymca3 жыл бұрын
@@gudipatimaheswari6855 basil mathew replyed on this ..you can try that way. I have not used after that so dont know exact solution
@gudipatimaheswari68553 жыл бұрын
Is it closed loop??
@nakiguler3 жыл бұрын
No, I just show power transfer.
@gudipatimaheswari68553 жыл бұрын
@@nakiguler is it Spwm??
@jeromegalleon13826 жыл бұрын
Sir can you share a schematic diagram for this
@sriharshaponakala23316 жыл бұрын
Inverter voltage not coming ? Please tell me the problem
@nakiguler6 жыл бұрын
check to the gate signals, input dc voltage and wt signal.
@pvn29365 жыл бұрын
how did you copy a ''from port'' out of a ''goto port'' @2:10
@nakiguler5 жыл бұрын
When mouse position is near the from or goto block, you will see a blue highlight. If you click when see this, it will automatically create from or goto.