2 Gang Switch Used as 1 Way Switches Connections Explained - Taking the Feed to the Switch

[@BobBenz55]

Again Nicely explained. Taking to feed to the switch is so much easier to work out. Been doing this method to my old house. At least most switches have a neutral now. So easier to add the new fancy switches which require neutral 😇

[@TheLondonHero]

Thank you! was not sure why off was on and on was off. Switched the wires and worked perfectly :)

[@GSHElectrical]

👍🏻

[@Terrybikesandmusic]

Very well explained 👌

[@GSHElectrical]

Thanks

[@alanbotfield2308]

Many thanks for explaining and making this switch wiring so simple, I needed to replace my old worn switch but didn't understand the wiring, now I know, cheers

[@David-qe6wq]

Well explained thanks

[@GSHElectrical]

Thanks

[@Marcel_Germann]

In Germany 1-way light switches are no longer a thing for some time. It's actually cheaper for the manufacturers to manufacture more 2-way switches instead of manufacture 1-way switches on a separate line. Especially since it is easy to use a 2-way switch for a simple on/off application. That reduced the prices of these switches, before they were more expensive. But since they became standard, the prices dropped.

[@GSHElectrical]

Thanks for the great comment 👍🏻

[@Chequr_Prostate]

Germany failing to to save the planets resources again, just for profit. 😉

[@drinky172]

I've seen someone else ask it, but it wasn't answered - what is the need for the 4th neutral and permanent line (the one that "goes out" - not to the lights), where's it going? And why? Is it necessary? If you don't need to connect to another bedroom can these simply be left out?

[@markgourley3745]

Wouldnt it make more sense if the first switch (closest to the bedroom door) be the bedroom light switch as it would be the closest? That would make the switch closest to the en-suite the en-suite switch.

[@Derek-qu8qi]

I’m trying to do this, BUT, the left switch is two way as in it’s my living room light that can also be operated by another one way switch. I’m trying to use the right switch to operate a separate light (external). Been advised to run neutral from a light and live from the switch, but not working.

[@sawdustwoodchips]

Would it be possible to convert this two gang one way switches to a two one way dimmer?

[@jamestaggart79]

Hi Gaz, any chance you can drawn the wiring diagram for us to see.

[@GSHElectrical]

Wiring Diagrams for Lighting and Motor Circuits kzbin.info/aero/PL2Ea5r9gxUUfm4SACOSOZigCeSxxC5xaO

[@taffythegreat1986]

Have you a video on bringing your live feed to the roses instead of the switch. Like the video 👍👍👍

[@glenster2000]

Where does the 4th neutral wire go? I understand there's one from the source to the connector and one to each of the two light fittings, but can't figure out what the other one is doing

[@Dr.Stacker]

So to make things fun, I would like to do the same thing, 2 plate method but with 2 gang smart dimmers which require 35mm backbox,.Would I be fine with a 35mm back box? Im afraid for to force the issue with a 47mm backbox as the internal block is about 50mm ish haha? Thanks in Advance!

[@stuartibbotson7179]

epic video thank you

[@GSHElectrical]

Thanks for watching 🦾

[@geddyboy1]

Love this video didn’t know it could be done like this but question what is the other end connections wire like e.i. Is all the lives in one way go clip and all blues and earths the same in there own way go clips then just follow the procedure in this video and that will give me to separate switches for two separate lights from one live feed , apologise just in the middle of lowering ceiling and want to have a central fan light on one switch and down light on a separate switch like your video so was wondering would this work

[@craigcotton4978]

The loop link is just like the jungle.... massive 😄

[@IAmThe_RA]

😅

[@taylorjohn7388]

Could the bridge then be used for a 4 gang so have three bridges for 4 switches?

[@Dr.Stacker]

It could but aren't you worried about the fact that you'd need 6 twin and earth cables and a monsterous backbox to fit everything in?

[@goldenwatery5k]

I have just connected the 2 Gang Switch, but there are some problems, when I click up the button.. the light is on, when i click down the button is if off now.... the button is reversed... I m wondering .... am i making some mistake on the L1 wire?

[@Hobobanobo]

I have this but only one switch of the two works and it controlls both lights. Im so confused.

[@Mega_sleepy]

What is the need for the loop from COM to COM?

[@davidr5964]

To feed the live to the second switch.

[@simonsupersi2225]

My justice light only works when hall light is on .I do t want hall light on

[@wakeupnow_777]

Take the lightbulb out 🤷🏻‍♀️

[@MussaMagagula]

srry i have a problem can i get help, i need help if we can agree

[@paddyhomebrew4497]

Hi, I have an issue with my landing light. When I turn the downstairs switch off I cant turn the light back on upstairs. But if I turn the downstairs on then I can turn the light on and off upstairs.

[@CAR_SOLUTIONS]

Probably loose connection 🤔

[@thereal1006]

its wired wrong

[@Mike_5]

This is your wife making sure you cannot enjoy yourself

[@robertburrows6612]

If anyone asks can you use a two gang switch as two one way switches then they shouldn't be.anywhere near electricity.

[@amaddinthenow]

Why so? I see no safety breach.

[@se9225]

on that thought... 30/1/23 allegedly tested & reported to IET Wiring Regulations BS7671 Requirements for Electrical Installations using the above method uses a single yellow/green 3m (approx) sheathed wire for the switched live? Installed by a 'qualified Electrician'? Another light switch with metal back box, broken CPC and held on the wall by paint!! I'm not qualified as a sparkie but even I know that's wrong/dangerous. These videos are educational and provide proof of the CORRECT way - even for us DIY's or other professional roles.

[@Jo3yW]

​@@amaddinthenowthe question demonstrates such a massive lack of understanding that they probably shouldn't even be allowed near sharp objects 🥴