Teardown engine /timming and valve clearance adjustment cleanning refresh engine step by step. gx35 4strokes brusscutter grasscutter scooter engine. tamsdemo
Пікірлер: 181
@livquitain18732 ай бұрын
Thank you so much Sir. Very nice tutorial....very detailed & very revealing. May your kind of specie multiply. God bless you po
@tamsdemo2 ай бұрын
Thank ypu Godbless
@rogeragravante7372 жыл бұрын
paps thank you sa vlog mo.dagdag kaalaman.5 grass cutter ko lage na lng binalik sa mangayus.pero ngayun ako na gagawa
@tamsdemo2 жыл бұрын
Yes idol. .madami ako vlogs about sa grass cuter 2 stroke 4 stroke. Nood kalang brader. Salamat
@efrencadiente5926 Жыл бұрын
Laking tulong Ng video NATO idol para sa baguhan na may gx35 na makina tnx
@tamsdemo Жыл бұрын
Salamat idol
@RomerDugos1234-od1zn4 ай бұрын
Boss more power ....the best ang video ninyo...
@tamsdemo3 ай бұрын
Salamat sir Godbless
@user-op8tn3yt3vАй бұрын
Salamat sa detalyadong tutorial brod...God bless...!
@tamsdemoАй бұрын
Salamat
@georeypescador1506 Жыл бұрын
Very informative video. Thanks.
@tamsdemo Жыл бұрын
Thank you sir. Pa subcribe narin sa aking channel salamat po. Godbless
@omranerden8495 Жыл бұрын
Sayende çözdüm tşk ederim ❤
@tamsdemo Жыл бұрын
Thank you 🤍
@Hydrogenblonde Жыл бұрын
A very helpful video.
@tamsdemo Жыл бұрын
Thanks alot sir. Have a good day
@teamlumayno2602 Жыл бұрын
Ayos. 👍
@nelsielanzaderas38812 жыл бұрын
👍👍👍
@zzayyoooaayyooo938 Жыл бұрын
Galing👍💪💓💓💓
@carloslucas787114 күн бұрын
Sana po me video ng valve at pag check ng seal.
@kaizergaming94182 жыл бұрын
Galing
@arielbayona69582 жыл бұрын
ayos boss may natutunan ako tagaL kna nag hahanap ng video 4t Gx35 po...
@tamsdemo2 жыл бұрын
Salamat bos idol..
@tamsdemo2 жыл бұрын
Paki share nmn ng videos ko sa.wall mo idol para namn ma.dagdagan ang aking subscriber salamat boaa
@efrencadiente8832 Жыл бұрын
OK ka lods malaking yan
@mrl258211 ай бұрын
At 55:55, you 'tighten' the flywheel nut BY HAND. A torque of 22.6 Nm is specified, not 'hand tight'. The nut doesn't seem to be making contact with the flywheel face and the shaft end doesn't protrude through the nut. Right until the last few minutes of the video, you don't seem to touch this nut ever again. Therefore the flywheel isn't secure on the shaft and could come loose at any time, causing extensive damage to machine and, possibly, the operator.
@tamsdemo11 ай бұрын
Yes thank you for recomendation and observation sir 🫡
@user-yh8is9iq4t11 ай бұрын
@@tamsdemoexcept
@mallikarjunmali53612 жыл бұрын
Agrimte 425 T ka timing belt kaha milega
@garuteofficial11302 жыл бұрын
boss anong tawag sa saksakan ng sparkplug? may nabibili bang ganun?
@xx38683 ай бұрын
Hi, this has a splash system? So how does oil get up to the tappet area? Same splash? No pumps on these type? I got a 24cc Yardking trimmer and it makes no smoke or smell BUT seems to use a tablespoon of oil every 30mins?? i have to keep topping up little 70mm sump. There is plenty of air coming out of breather and spits a bit there too. Thinking somehow the piston ring might be stuck or worn bore area from last user might have run it dry of oil ect. Rockers go up and down a lot so cam might be ok. Watched you video just as prep to pull apart.
@tamsdemo3 ай бұрын
It has a propeller connected to the crankshaft that delivers the oil to the head and it has also flap valve on the bottom of the crancase serve as pump leading the oil pass thru the rubber hose from botton to the head if you see the black hose like letter C thats the one delivers oil from bottom to the head. Also the timming belt also submerge to the oil on the bottom of the crancase leading the oil go up to the head also. This kind of 4 stroke engine has crancase oil of 100ml . This migth help .. Its my firstime also to hear an engine needs topping up engine oil the engine that you have now i wonder thats a nice or an old or antique engine nice collection.
@xx38683 ай бұрын
@@tamsdemo Yeah, it eating oil by the minute!! No smoke or smell and when i pulled the carb, the pump gasket was missing but the others were there?? I wonder if the piston rings will be there when i tear this down?? Very strange as its only 2 years old but the gearbox was dry and the shafts too and the ignition coil wasnt even gapped against the flywheel?? So when i tried starting it when got it, it surged horribly and fuel came out the carb and would do that without a pump gasket flaps. Spark plug was used and black so other user must have tried to run it ? Wonder if it came from the factory missing all these things?? and not greased and will there be piston rings? Runs quiet and smooth so oil "swisher" hopefully will be there lubricating. also tappets were way gapped. I dont have specs so made them .1 and .15 mm. Also i cant do compression test as it has that tiny 10mm plug and dont have a adapter, might make one and do comp test. Cant run it like this so have to open it up and see if stuck rings?, that would be great as where will i get rings as few spare parts online for this yardking 883222 model. Thanks for your reply
@tamsdemo3 ай бұрын
@@xx3868 @xx3868 try running it at nigth and check if there a black smoke comming out to the muffler by pointing flashligth. Ill try to find or check also your engine yard king it seems like u have a knoledge why and engine works . Well you can tear it down to check weather theres a problem inside then engine just make a vide or photo every work you do so you dont miss every detail when you put it back speacily screws ang bolt . I gey back to you as soon as i have got update on your yardking engine ✌️
@xx38683 ай бұрын
@@tamsdemo Yeah i pulled it apart and it has a oil pump!! Little hose going into sump and no swisher or propeller ect just crankshaft and bearings. Next problem is where to put the sealant as the two mating surfaces have oil gallery runs i guessing up to the top and here and there so if i get it wrong, i block off a oil supply somewhere. good lucking finding a video of this engine being disassembled haha. Lots of damaged threads and the rings were all loose and free and springy and gaped about .2 to .25 mm near the top where they would be widest so not really worn. all looks clean and tidy so maybe blowing past the rings as no leaks of course so has to be burnt or pushed out the breather but i not seeing a tablespoon coming out, just a bit found in the air cleaner after a short run. Maybe crappy chinese bores and rings and just worn. Will assemble and run it as it is. will gap the top rings 180 and the oil ring sameish and see how it goes. I have to work out where to put the sealant as the bolt holes seem to be where the oil runs and oil will go through them?? will have to study it deeply try to work it out. Block has a chinese? name on it so something i dont recognise. all the damaged threads and mess i have found with this all over, cant be high quality.
@tamsdemo2 ай бұрын
@@xx3868 yeah bro if you were thinking were to put the sealant may be theres no other way igues you should put a paper gastket on it and learn were the oil goes and pas thru. But now you find it having a serial or name on it chinese parts we all know parts at cheap and easy to worn out some chinese.engines are disposable but some are repairable by putting original parts as if the engine are clone to original maybe japan or german usa made engine lol😆
@marcosbarriga62822 жыл бұрын
we're did you buy that sprocket adapter??
@tamsdemo2 жыл бұрын
We call it clutch bell. You can find it online stores
@sivaprasadmiriyala51822 жыл бұрын
What are the equipments require to separate and refitting
@tamsdemo2 жыл бұрын
5mm allen key 4mm allen key Flat screw driver Puller 12mm socket wrench
@sivaprasadmiriyala51822 жыл бұрын
Thanks 🙏 Bro
@joelsuela93182 жыл бұрын
Salamat bro tamsdemo Kawaan tayopalagi sa biyaya ni Abba Yahawa
@tamsdemo2 жыл бұрын
@@joelsuela9318 salamat bro
@raitenshourai36282 жыл бұрын
sir pag naka velocity stack ka na saan na ikakabit yung hose na dating nakalagay sa stock na air filter?
@tamsdemo2 жыл бұрын
Wala.na pag kakabitan tutok nlng po sa baba
@BOOSTEDLCS1327 Жыл бұрын
First time ko lang mag backlas ng GX pero naputol yung belt after ng rebuild 😂😂pero ok na
@tamsdemo Жыл бұрын
Ayus yan boss
@nonoyempleo57229 ай бұрын
boss, ask ko lang po, bakit yung bagong bili ko na gx50 may tumutolung langis sa may flywheel?
@tamsdemo9 ай бұрын
Oilseal po yan bos baka di maganda pag kaka lagay sa manufacturer isa din bos dahilan ung valve cover mo sikipan mopo dun madalas nag tatagas. Check mo allen keys bolts sa makina kc maluluwag yun
@sivaprasadmiriyala51822 жыл бұрын
Pls give me online purchase link for buying spare parts for tiwan sphere
@user-dd2xg5yz7q Жыл бұрын
amazon (o・ω・o)
@exequielgalos5883 Жыл бұрын
Sir pwd manghengi sa mannual nyo gx35 mayroon ako mahirap takbo
@suneetkumar6712 жыл бұрын
Typhoid bal set karne ka tarika Hindi mein bataiye
@efrensantos561 Жыл бұрын
Talaga po ba na naglalangis ang ibabaw na kinalalagyan ng dalawang valve pag tinanggal ang cover e meron langis !?
@tamsdemo Жыл бұрын
Meron yan konti lng po pang lubricate ng stem. At spring. If madami sira or may leak po ang divider ung oring nasa takip po.
@cristinacayanes57402 жыл бұрын
boss ano ba pinag kaiba ng big carb na 4stroke sa stock na carb ng 4stroke
@tamsdemo2 жыл бұрын
Mas malaki butas openning para sa air intake . At mas malaki jet. May adjusan din ng fuel ratio
@cristinacayanes57402 жыл бұрын
boss may nkita sa isang channel nilagyan ng bulak ung loob head cylender bago nya ilagay ung piston pwede po ba un
@tamsdemo2 жыл бұрын
Possible.kc ung valves nya baka mahulog para maipit ung valve pag top ng piston .
@joelsuela93182 жыл бұрын
Good pm bro Salamat Kay Abba YAHAWA sa blog mo bro
@tamsdemo2 жыл бұрын
Salamat sir joel
@joelsuela93182 жыл бұрын
Bro tamsdemo ayaw umandar ng gx 35 ko mula ng pinalitan ko ng clutch pinalitan ko ng carburador na bago at egnition coil at spark plug ayaw parin umandar binuksan kona pati piston nilinis ko ayaw padin umandar bro ano kaya prolema palitan na ng makina bro
@tamsdemo2 жыл бұрын
@@joelsuela9318 posible nawala.na sa timming.
@tamsdemo2 жыл бұрын
@@joelsuela9318 padala.mo.sakin sa fairview
@joelsuela93182 жыл бұрын
@@tamsdemo sige boss ano address jan boss
@shielarobles4588 Жыл бұрын
Sir San location nyo po pagawa ako grass cutting
@joelsuela93182 жыл бұрын
Boss tamsdemo wala ka bang second hand binibenta na flywheel G gx 35 nabungian kasi ng 1/4 ang fly wheel ko
@tamsdemo2 жыл бұрын
Wala pa.master pag meron balitaan kita
@joelsuela93182 жыл бұрын
@@tamsdemo Salamat boss tamsdemo
@jeffreydadesvlog4323 Жыл бұрын
panu po kung nabali yun panu po pagpalit
@JandBPedvlogger001 Жыл бұрын
kapag nagoverhaul poba need paba palitan ng Bearing saka gasket???
@tamsdemo Жыл бұрын
Depende if may clearance na ung bearing sir.
@ryangarcia82782 жыл бұрын
Pde po ba gmitin as an engine for bike project..?
@tamsdemo2 жыл бұрын
Yes pwede po
@evnerpegarum7270 Жыл бұрын
Sir gd day po Ask lang po paabo po ba e change oil young .makita land mawer Tnx po
@tamsdemo Жыл бұрын
Pag 2 stroke engine no need mo . Pag 4t un po need change oil
@allanarrieta58064 ай бұрын
Kelan po ba inumpisahan yang exploration Nyan china. Sino po ba ang presedente noong nagtayo Sila ng machine na Yan?
@tamsdemo4 ай бұрын
Japan po origin ng makina ma ito ginaya lng ng china sir idol
@sivaprasadmiriyala51822 жыл бұрын
Where we can buy the spare parts
@tamsdemo2 жыл бұрын
www.ereplacementparts.com/honda-gx35-type-satvin-gcacm10000011099999-small-engine-parts-c-37657_37658_37938_38514.html Here you go
@user-dd2xg5yz7q Жыл бұрын
amazon (o・ω・o)
@wackyadriano1052 жыл бұрын
idol saan nakakabili ng timing gear na mas mataas ang lift?
@tamsdemo2 жыл бұрын
Cam.ang may lift wala.po sa timming gear
@bemartys.tvhunt71932 жыл бұрын
Paps parehu pang ba Ang pyesa ng original Honda gx35 at fake?
@tamsdemo2 жыл бұрын
Same
@armelprado5693 Жыл бұрын
sir paano po tangalin ang rocker arm gx35 grasscutter
@tamsdemo Жыл бұрын
May pin ung rocker arm i remove molng un sir
@joelsuela93182 жыл бұрын
Good day bro tamsdemo napaandar ko bro ang gx 35 ko kaso namamatay nabungi ng 1/4 Yung flywheel ko Hindi naman nabungi sa rapar ng mangnet doon Lang sa mga ngipin nata Yung 1/4 ng fly wheel nahati però umandar papalitann ko ba boss ng fly wheel thanks po sa Abba Yahawa kristo na atin tagalikha
@tamsdemo2 жыл бұрын
Ayus yan bos. Magaling
@babykosikulot5213 Жыл бұрын
Sir kailngan ba talaga may silicon, yung sakin kasi natagas ehh ..
@tamsdemo Жыл бұрын
Yes pwede nmn sir.
@rogercruz78682 жыл бұрын
Sir paano tanggalin ung rocker arm ng gx35 q.stock ung isa ayaw gumalaw.tnx
@tamsdemo2 жыл бұрын
Naka.press kc yan lods
@wanderingandroid Жыл бұрын
bos, china yan na gx35 o orig honda?
@tamsdemo Жыл бұрын
Clone china
@arnoldoreal43332 жыл бұрын
Sir may shop po ba kayo or nag seservice po kayo ?
@tamsdemo2 жыл бұрын
Nag se service.minsan sir
@mylamendoza2300 Жыл бұрын
Sir bat may sprocket yan brush cutter mo,pra saan yan?!
@tamsdemo Жыл бұрын
Kaya may sprocket po kc nilagay sa standup.scooter po itong brushcutter.
@garuteofficial11302 жыл бұрын
boss any tips pag nag nalose thread un salpakan ng spark plug?
@tamsdemo2 жыл бұрын
Pa machine shop mopo para ma taniman bagong thread
@garuteofficial11302 жыл бұрын
yung machine shop daw po dito wala daw silang size nung butas
@ferdinandgutierrez25582 жыл бұрын
Boss saan ang place nyo baka ma help ako sa scoot ko
@tamsdemo2 жыл бұрын
Fairview aydol lodi
@harruldcantillas47982 жыл бұрын
Boss, anong sukat ng flywheel ng gx35? Kasi yung binili namin na flywheel di magkasya. Pero gx35 dw yun na sukat. Or iba2x sukat ng flywheel ng GX35?
@tamsdemo2 жыл бұрын
Baka.nmn pang gx 50 un bos or pang 2 stroke ang nabigay sa inyo..
@harruldcantillas47982 жыл бұрын
@@tamsdemo siguro boss. May 2 stroke ba na gx35 boss?
@tamsdemo2 жыл бұрын
@@harruldcantillas4798 wala.po 2t na gx35..san moba na bili.yan sir.
@harruldcantillas47982 жыл бұрын
@@tamsdemo sa shoppee boss.. 4600 di pa kasama shipping boss
@tamsdemo2 жыл бұрын
@@harruldcantillas4798 ah.
@exequielgalos588310 ай бұрын
Sir yong carb nato ayaw mag pump walang pumasok na gas sa carb paano
@tamsdemo10 ай бұрын
May singaw po yan . Baka po sa hose.mo.may punit or ung prime bulb sa carb buttas po.
@banzonmemavlog55772 жыл бұрын
ung timing gear ko po hndi mahugot hndi maitulak ang pin.. pano mataasan ang lift?
@tamsdemo2 жыл бұрын
Pukpukin mo lng
@banzonmemavlog55772 жыл бұрын
@@tamsdemo ano po pwede gawin para tumaas ang lift?
@richarddonoso40702 жыл бұрын
Boss baka matulungan moko sa 4stroke ko
@tamsdemo2 жыл бұрын
Oo nmn boss. Pa.silip din ibang mga vids ko sir may mga 4t dit tips.dyan
@selcukeken6791 Жыл бұрын
Pistonu kaç mm
@tamsdemo Жыл бұрын
Thank you
@selcukeken6791 Жыл бұрын
Pistonun ölçüsü kaç milimetre ebatı nekadar.
@tamsdemo Жыл бұрын
@@selcukeken6791 39mm . Piston
@abigaildao6310 Жыл бұрын
boss san po location niyo? hirap po kasi kami gawin to, ginawa na po namin lahat, ayaw talaga.
@tamsdemo Жыл бұрын
Trymo palitan carb. Or minsan sa tappet clearance ng iyong valve
@bravewave732110 ай бұрын
boss ask ko lng same ba ng size ng flywheel ang gx35 at gx50? salamat
@tamsdemo10 ай бұрын
Hindi ako sure sir i check kopo specs. Thank you
@bravewave732110 ай бұрын
@@tamsdemo ano po kaya issue ng gx50 kapag mabilis nang maubusan ng langis?
@tamsdemo10 ай бұрын
Posible may leak na sa oilseal sa segunial . May tama na piston ring Valve guide at seal may leak na.
@user-rk3oz9ps8i9 ай бұрын
anong pangalan ng hose n letter c n black sir
@tamsdemo9 ай бұрын
Mula baba ang head hose po yan para sa lubrication o galing sa oil pump .
@tamsdemo9 ай бұрын
Hindi ko kabisa sir ung name . Pero dyan dumadaan ung lube oil papunta sa head. Lube oil pressure hose
@emardcanedo17662 жыл бұрын
Sir ano po kaya problem naghalo po kasi ung langis at gas ng gx35 namin bagong bili lng halos ilan beses pa lng nagagamit?
@tamsdemo2 жыл бұрын
Wala po iba dadaanan ung gas papunta sa crankcase . Kaya imposible po.mag halo gas at oil. Mas mataas po presure ng oil compare to presure sa gas galing carb . Dipo aandar yan kapag ganyang cenario
@emardcanedo17662 жыл бұрын
@@tamsdemo salamat po Sir update ko po kayo dndrain ko n refill bago oil
@josephfollante72009 ай бұрын
Sakin gx35 din pero nkpalit nko carburetor,, laging palya parin,, pag na adjust ko ok naman mga 15-20 mins. hahagok na naman,, ano kaya solusyon
@tamsdemo9 ай бұрын
Check.mo.idol.hose.baka may butas.. Palit karin new sparkplug.
@josephfollante72009 ай бұрын
@@tamsdemo ok pa sparkplug, at bago mga fuel line, idol,, baka itong bolt na isa sa nakasabitan ng carburetor loose thread isa,, bago dun singaw sa manifold gasket nya
@tamsdemo9 ай бұрын
@@josephfollante7200 yes check.modin yang bolt dyan sa carb
@josephfollante72009 ай бұрын
@@tamsdemo ok idol salamat
@johnjohneljacinto68242 жыл бұрын
ung fly wheel ko nabarag 😓 hirap tangalin
@tamsdemo2 жыл бұрын
Gamitan mo.puller bos
@sarahsantaana667 Жыл бұрын
Kulang ang guide d pinaliwanag paano kabit ung sa gitna ung my magnet problema k kc paano tangagalin
@tamsdemo Жыл бұрын
Puller po if meron kapo. May guide almost same nasa mga videos kopo salamat sir mam. Godbless
@jeffrieuy55442 жыл бұрын
Di ko kayang buohin Yan hahaha
@tamsdemo2 жыл бұрын
Kaya mo yan boss basta ma subaybayan mo ang mula umpisa hangang huli.
@buboybubuyogtv9 ай бұрын
sir thailand made po ba yan or original honda?
@tamsdemo9 ай бұрын
Class a copy china po ito
@buboybubuyogtv9 ай бұрын
same lang po ba ang parts sa original? @@tamsdemo
@tamsdemo9 ай бұрын
@buboybubuyogtv yes sir idol
@buboybubuyogtv9 ай бұрын
@@tamsdemo salamat bossing🙏
@kimjoshuaevangelista6266 Жыл бұрын
Matatangal po ba ang camshaft nya boss?
@kimjoshuaevangelista6266 Жыл бұрын
Nabali po kasi samin
@tamsdemo Жыл бұрын
Palit na buo po
@kimjoshuaevangelista6266 Жыл бұрын
@@tamsdemo ay sorry boss😁 rocker arm pla nabali hehe.. matatangal poba yan?
@tamsdemo Жыл бұрын
@@kimjoshuaevangelista6266 yes na tagangal po yan
@archimdejesus31882 жыл бұрын
boss tanong ko Lang po kasi Yung gx 35 namin po bigla po humina bago Lang po yun Pina tune up na po namin pero mahina parin po pumutol ng damo
@tamsdemo2 жыл бұрын
Clutch po. I check nyo po. Baka upod.napo
@tamsdemo2 жыл бұрын
If malapit po kayo fairview q.c.pwede nyo po dalhin dito sakin.
@archimdejesus31882 жыл бұрын
@@tamsdemo boss said Pampanga po ako malayo po
@archimdejesus31882 жыл бұрын
@@tamsdemo boss Kasi Yung ibang nag aayos parang walang Alam sinisilip Lang nila
@archimdejesus31882 жыл бұрын
@@tamsdemo Yung clutch boss makapal pa po nkita ko nung binuksan nila
@wellykho4142 жыл бұрын
bakit may lumalabas n langis sa may foam?
@tamsdemo2 жыл бұрын
Breather po un kadugtong dyan
@wellingtonngo84432 жыл бұрын
@@tamsdemo bro ano Dapat Gawin yan?
@tamsdemo2 жыл бұрын
@@wellingtonngo8443 100 ml lng ang langis dapat wag sobra.