Mine had that sensor on the crank too, I just ran a 0bd1 dizzy and it works fine
@stefeninspringfield Жыл бұрын
That's cause In the older cars it is in the dizzy just take that out and run a obd1 dizzy and ecu
@802Garage2 жыл бұрын
Dang that engine is looking niiice.
@MtGarage2 жыл бұрын
So scared to scratch it now 😅
@Thatonehondaaa Жыл бұрын
Glad I ran into this video 🤌🏼im new to the h series stuff and this really did help me a lot appreciate you 🤙🏼
@MtGarage Жыл бұрын
Glad I could help, thanks for watching🤙🏻
@nhoegil7070 Жыл бұрын
Same I was a D 😅
@ahmadfarhan51722 жыл бұрын
Hey Bud,I wanna ask about how to tight the timing belt? I so struggling to make it tight😅...Can U make the video for that?...
@lokeyracing301511 ай бұрын
96 in the bastard year... They put out obd1 an obd2
@alexferreira6081 Жыл бұрын
Question about the balance shaft belt, the rear balance shaft gear has a Dot on it, where is it suppose to be pointing?? 11 o clock position??
@maleco26142 жыл бұрын
Where the dowels easy to get out? what did you use? BTW Nice engine.
@prometheus1607 ай бұрын
my 98 bb8 h22a8 does not have a crank possition sensor
@suyisavage12392 жыл бұрын
how did you get the motor to top dead center just lign all the marks up
@jensenmoon72882 жыл бұрын
How did you make sure the cams were set at TDC?
@MtGarage2 жыл бұрын
When installing the cams, make sure the key is pointing upwards. Once the cam gears are installed there will be an arrow on each one pointing up. There will be 2 timing marks on each cam gear. You want to line these up with the top of the head and make sure the gears are lined up with each other. It can be difficult to keep them in place because there will be some tension on the cam lobes. They do make a tool that holds the gears in place while installing the timing belt, but I was able to make it work without the tool.
@josesebastian78465 ай бұрын
Can someone help me with my timing belt for my 96 prelude Si. It snapped and I have no idea how to TDC the cams before installing a new timing belt.
@dragonclubracing86692 жыл бұрын
Hi I have a 4th gen 1995 prelude 2.2 vtec the h22a4 I believe, are the timing belt kits the same between 4th, 5th gen and accord type r's? As I'm struggling to find a timing belt kit for the 4th gen. Needs cambelt, tensioner balancing belt and water pump? Thanks
@vincentguzman19922 жыл бұрын
Awesome vid. Nice to see more h22 builders , have a instagram to follow?
@MtGarage2 жыл бұрын
Thanks buddy! Our ig is mtgarage_official. Haven’t been very active on there in a while. But will try to get on it again.
@H22a4accord Жыл бұрын
Hello underneath the center cam cap is there just an o ring that goes in that circle groove or is there an actual oil restricter piston that is removable?
@mulakabdul4303Ай бұрын
The o ring goes on the orfice not above the orfice like he had installed.
@monstersquashracing2 жыл бұрын
Awesom work man. 👌🏻👌🏻👌🏻👌🏻👌🏻
@OldSchoolNoe2 ай бұрын
cool!
@beastfromtheeast8439 Жыл бұрын
You sure do have some girly soft looking hands you touch that engine with the upt most soft touch anyone has ever seen lol gjgj
@brandonhackley70673 ай бұрын
Love the vidoe
@rogermorales85492 жыл бұрын
Yo how did u get the belt to slide on the last cam gear it cut off…. Im struggling lol
@MtGarage2 жыл бұрын
It can be a bit tricky to keep everything lined up. If everything is lined up right, it should slip on fairly easy. My belt was a bit tight from being so cold out, so ended up having to lightly pry on it with a plastic trim tool. Not the ideal way to do it, but it worked. Hope it works out for you buddy 🤙🏻
@nzzgcg4217 Жыл бұрын
instructions unclear, my wiener is now stuck in the engine
@nzzgcg4217 Жыл бұрын
jokes aside great vid
@yangxai33172 жыл бұрын
Nice 👍.
@aaronclarke94152 жыл бұрын
What ecu and trans are you using
@MtGarage2 жыл бұрын
Currently running a chipped P28 by clubbed inc for the NA setup. will be running a Hondata S300 for the new engine with boost.