Hair Clipper Blade Assembly, Maintenance and Cleaning (how to)

This video explains the maintenance, cleaning and assembly of Hair Clipper Blades.
Apart from regularly applying hair clipper oil, the blades of a hair clipper need to be maintained once in a while.
We show how to remove the clipper blades from the unit and which parts need to be cleaned.
The assembly process requires special attention. Otherwise the machine may be harmful during the next hair cut. Make sure to follow the instructions.
At the very end do not forget to apply a few drops of hair clipper oil for proper lubrication.
Hair Clipper Oil (Amazon Affiliate Link):
amzn.to/38k4ZVa

[@jjkarwowski]

I noticed my Wahl being noisy so I loosened the screws and it suddenly ejected off like a sling shot! All the blade and components holding them together blew apart like a grenade. I attempted to put it back together, but trying to place the spring back inside threw me a giant curveball. I couldn't get it set right. I watched over a dozen Wahl KZbin DIYs and not a single one discussed it or showed a close up. I was about to give up, until I watched your video. I know you didn't go into detail about the spring, but you had just the right closeup angle and it was enough to help me put it back together successfully. It now hums like a gentle hummingbird. Thank you!

[@brianmeinking2723]

My girlfriend had taken apart the blades to clean and re-oil but had forgotten how to reassemble it. We both watched this video and learned a lot. We reassembled and aligned the blades then applied the oil. Thanks for the great video!!

[@TheRealJohnDoe2.0]

You didn’t take out the plastic piece with the spring. I took out mine and now im having trouble putting it back.

[@bembesully8360]

Now that's the details I needed..thank you

[@adysen]

Outstanding and easy to follow tutorial. Thank you for teaching me how to care for my hair clippers the correct way!

[@matthewbuzzard4024]

Thanks. I never knew that u had to do all of this

[@JockeyCake]

Excellent video. Thank you

[@shelby3822]

Thank you - took mine apart to clean and didn't adjust... started biting my neck immediately

[@annakortukov2845]

Thanks, great video! 👍☺️

[@Sarah-hz3gy]

Thank you, the way that you showed the blades up closely with plenty of light, how they were to be aligned properly etc... very helpful! It wasnt easy to keep blades in position and still, until screwed in tightly, however perseverance pays off!!! Thank you again :)

[@russ1669]

great and clear instruction thankyou

[@noy5626]

Thanks! Helpful video 👍

[@alexiariley2827]

This helped so much thank you!

[@deficoinfx7863]

Thanks for the help

[@ramonmaldonado7570]

Thank you for the vid

[@duragggura3695]

Great Video...clean cut instructions..kudos!!!

[@MegaSafetyFirst]

Thank you, I appreciate your feedback! 👍

[@IM-xg2ki]

So nice, thank you! YOu saved me! :D

[@donnadavis9934]

Thank you for sharing this video! You demonstrated in such a clear and simple way. I had taken ours apart to clean them but have been afraid to use them since bc unsure if they were put back Together and adjusted properly. after watching your video I reassembled them per your instructions and they're working great!

[@johnvicars9382]

The white component, along with its spring (situated in the cavity beneath the blades) popped out as I was removing the blades, and I can't figure out how to re-attach the spring to the white component. Any suggestions?

[@baselkaskas2093]

Fk mine too did u figure it out 😂😂

[@rudygonzalez7690]

I followed the instructions in the video as best I could, but the top blade is loose. How can I fix that?

[@tshepontlhane8882]

Good afternoon I wanna know how to assemble from the inside

[@EfrenBonife]

How much