How does that heat on one side not warp the cam? (like torch straightening etc) do you clean up the bearing surfaces some how?
@jamesford29422 жыл бұрын
Nice, I like what you guys do.
@camshaftcasting1451Ай бұрын
Interesting. Is the journal-journal run-out unaffected by this process?
@stilpet90512 жыл бұрын
Could you spray weld it with oxy-acetylene and metal powder? What are the pros, cons in that repair? What are the specs (more info) on that cobalt hardfacing rod?
@tonyschiffiler48162 жыл бұрын
Can this process be used to increase lift on a flat tappet lifter cam for an older v8 engine?
@DELTACAM80056255002 жыл бұрын
Yes but not cost effective
@josecheo683 жыл бұрын
What kind of filler material do you use for that?
@woozhi92182 ай бұрын
Hard facing rod I suppose
@donm99517 ай бұрын
how bad is run out after all that heat?
@chaztiz88393 жыл бұрын
Can you guys resurface a pair of harley flathead cams for me??????????,,Im sure the setup for that is far different but is it posible???
@DELTACAM80056255002 жыл бұрын
if you could please send photos in an email to our website I can review them and reply to you there deltacam.com
@tyreeceneufville4553 Жыл бұрын
Does that give you more lift also?
@brianbloom17996 ай бұрын
Doesn't the Camshaft Have to be Heat treated again, after reground
@camshaftcasting1451Ай бұрын
Those cams a not heat treated, they are chill cast
@bonisyafialdi22862 жыл бұрын
Can we do it on bmw e36 m52 cam shaft? I need hight duration for race car
@CHRISINMCNEILL2 жыл бұрын
Can you regrind a Wisconsin V465D cam? It is an industrial air cooled V4 motor
@DELTACAM80056255002 жыл бұрын
Yes sir
@CHRISINMCNEILL2 жыл бұрын
@@DELTACAM8005625500 Thanks for the fast reply. I’ll get with you Monday. Have a marry Christmas!
@frostyab75792 жыл бұрын
what shielding gas mix do you use?
@bb21again.67 Жыл бұрын
I imagine that you first grind the lobes undersized before facing?
@ktmturbo58362 ай бұрын
Me to
@ratsmother46952 жыл бұрын
Hello, I know you don't answer anyone, but I'm going to try hahaha, what kind of contribution do you have to give to weld cast iron? After welding you have to cool down, do you have to give some heat treatment? I'm from Spain, so don't worry, I'm not going to take the job away. Thank you very much, you are a genius.
@littlereptilian75809 ай бұрын
Did you find out ?
@ibrahym.z25372 жыл бұрын
سلام اريد التواصل معك لو سمحت
@sebaslianza13123 жыл бұрын
Rod is colbalt ?
@garyfang84172 жыл бұрын
It's very good
@Jamesrdc2 жыл бұрын
What filler is that.
@paulshubsachs497711 ай бұрын
Hello James, I know this response is a bit late (!), but I rekon the rod is Cobalt 6 (sometimes called Stellite 6).
@angelisone Жыл бұрын
How much to weld & resurface one lobe on 1986 BMW 735i (E23)? What a piece of a junk car this is. Less than 51K & always serviced by BMW up to 51K. Now, sat for 20 years.