Part number: 69200080 HARNESS, W/ LED INDICATOR SPORTSTER 2014-2020 LIGHTING CABLE SPEEDOMETER CONSOLE HARLEY XL
Пікірлер: 22
@borboliuksstoruliuks75603 ай бұрын
Kiek kainuoja toks remontas?
@13thChip4 ай бұрын
i have been searching for this video for ages. Thank you so much. Which terminal you supplied 12V (Batt)? I see there were multiple pins in that socket. How do you distinguish the pin for + or - ?
@tmx66664 ай бұрын
If I remember correctly inside on the pcb board + wire is marked with B+, other wires which goes from Leds apply - to turn them on.
@13thChip4 ай бұрын
@@tmx6666 ok sounds good. Will check. Thank you so much. This means a lot to me. Subscribed to your channel as well.
@ashleysaunby20029 күн бұрын
Hi, please could somebody tell me the value of C1 capacitor? Thank you.
@tmx66669 күн бұрын
Unfortunately I no longer have this pcb, but could suggest couple options: 1. Do not add C1 at all, as you saw on video it was missing on my board and it worked just fine. This is only filter cap. 2. Add random capacity same size capacitor. 3. Cut tracks from near capacitor on your board and measure it with capacitance tester.
@alexpfd3 ай бұрын
Saludos desde México, muy buena información, es posible que envíes el diagrama que elaboraste??? nos serviría de mucho...alimentaste desde el cable a 12v??
@tmx66663 ай бұрын
Just found old drawing. It might be with mistakes mototomas.lt/harley-davidson-sportster-led-indicators/ But basically PCB is marked with L, H, B+, N, O, R, you can test by applying +12v to B+ and then connect minus to one of board contacts L, H, N, O, R
@REDsMedan6 ай бұрын
Hello sir, could u please let me know what type of LED used for that? Mine left sign is dimmed. Thanks
@tmx66665 ай бұрын
I do not know exact model, I desoldered used led from some old printer board. Possible LED smd package 3216
@REDsMedan5 ай бұрын
@@tmx6666 i see. Thanks sir
@olku2000995 ай бұрын
What was the voltage you applied to the positive terminal to test the leds?
@tmx66665 ай бұрын
When tested via wires I used 12 volts. When tested separate LEDs I used low voltage just to check if they work or not ~1.8v., was afraid to burn them.
@olku2000995 ай бұрын
Did you also set a current limiter or something?@@tmx6666
@ca197883 ай бұрын
How did you remove the board from the black enclosure?
@tmx66663 ай бұрын
Board wasn't glued or something. I just pushed wires from back and helped board to move out with small screwdriver.
@ca197883 ай бұрын
@@tmx6666 thanks. I was unable to push mine. i removed some corrosion from the front and it sort of works now.
@tmx66663 ай бұрын
Great to hear that 👍
@marcbelaidi81308 ай бұрын
Bonjour je rencontre le même souci sur mon sportster est-il possible d'avoir plus d'informations sur le mode d'opération. Merci
@tmx66668 ай бұрын
Hello, could you clarify your question?
@lokeshbharti73885 ай бұрын
I am facing same problem. The condition of con is worst, can you plz share circuit diagram and other perameters so that new one can be make.
@tmx66665 ай бұрын
@@lokeshbharti7388 I have no circuit diagram for it. Only quick drawing made during video.