{1254A} SMD capacitor short circuit detection tricks, Q&A

[@mohammadamin5225]

very good , how about parallel leds , if one of them is shorted?

[@HaseebElectronics]

the same method is to be applied for parallel LEDs, diodes, capacitors using 1volt to 1.5 volt with high current is awesome if we join D size 1.2 volt in parallel (4 to 6 cells). it will be useful tool (specially for LED TVs, satellite receivers, DVRs, CCTV cameras) or we can also connect D size alkline cells together for 1.5 volt

[@mohammadamin5225]

@@HaseebElectronics too much thanks answering my question dear Haseeb.

[@EmmanuelKalinde]

This issue is exactly whats happening with my laptop. The capacitor bank around the processor test short circuit. I still use it but it shuts down unexpectedly after some time. I was thinking the processor has a fault but now I will diagnose those capacitors. This is crystal clear and the questions are well answered. Thank you Sir

[@HaseebElectronics]

good evening in your case i think it is not a problem of capacitors. because if capacitor is short circuited then it will remain shorted, i think there is something is temperature effected. might be something is getting hot or overcurrent due to temperature

[@EmmanuelKalinde]

But Sir each of those none polarised capacitors is testing short circuit..

[@rajnishkaloi8591]

I read all the comments by Viewers when i watch your video, all the questioning comments increase knowledge, In last video you have answered the comments that was appreciable Thanks again for shareing ❤

[@HaseebElectronics]

wow it is awesome best regards for your valuable appreciation

[@k3ggaming926]

Always the best of all tutorials in youtube, thanks sir i had learned a lot from all your videos specially in smps🎉🎉🎉

[@tvbox8478]

👌👍

[@jaym5938]

Ah! You looked at the other side of the board to determine the polarity of the capacitor bank. That is the answer to my question. Thank you!!!

[@HaseebElectronics]

You are welcome!

[@Dennis-uc2gm]

👍👍 Its always nice to have "extra tools" for the times when we don't have more expensive ones.

[@Ianf1x]

I like learning and you have been a great teacher thank you . Hope you have good Christmas.

[@ghulamalivaraich7920]

Nice illustrations ❤

[@abbeyzondo]

As always, great tutorial. Thank you

[@HaseebElectronics]

best regards

[@Pozitiv_ion]

Congratulations for the video. Thank you for your time, it is not easy to do these experiments, seem to be simple but consume a lot of time.

[@chinnarao326]

Resp Sir! Dhanyavaadh Sir. 🙏🏻🙏🏻🙏🏻..... -- ChinnaRao Paderu Andhrapradesh

[@MdIsmail-ci5uy]

Helpful to find Short circuit thank you sir

[@rajkhumar001]

Really awesome sir. Really enjoyed it😊😊

[@HaseebElectronics]

it is my pleasure. best regards

[@rajkhumar001]

@HaseebElectronics thank you sir.

[@kaleelurrahumanrahuman99]

Sir you are smart I'm watching your channel regularly Allah bless you from srilanka

[@muhammadishtiaq24]

Excellent thanks for sharing this informative video keep sharing❤❤❤

[@HaseebElectronics]

best regards

[@integers1710]

Ik trick me b btaon sir! Apne ohm meter ko lowest available range pr set kren, or ese parallel capacitors pr har capacitor pr ohm check kren, jis capacitor pr ap ko lowest reading mile ( even k wo comparatively 0.001 ohm kam hi ho) us capacitor ko remove kr den, closest short or kuch dori pr short me kuch farq hota hy, ap practically kbi check kren, kisi jga ye trick kaam aegi inshaAllah

[@HaseebElectronics]

thanks for your valuable comment you are right. in this condition we need an accurate multimeter the best multimeter is to be used for this measurement is 4-wire multimeter. detecting fault using ohms method is slightly time taking and difficult. we can use milli-ohms methode or microvolt method

[@mariotorres5283]

saludos, el metodo a 4 puntas tambien es muy practico

[@jluke6861]

Thank you for your videos.

[@HaseebElectronics]

It is my pleasure

[@Edmorbus]

Good information Thanks for sharing

[@HaseebElectronics]

Good eveneing. best regards

[@theexpatchannel0121]

nice buddy

[@MihaiNicola-pf7uh]

1:00 good

[@habibkhyata2983]

👍👍👍👍

[@tvbox8478]

👍

[@maiconjz3527]

10.😊

[@rajuradios]

sir i think it will be better idea to use rosen paste instead of this cool spray. its actually evaporating very fast. it may work in your scenario, but if we are finding shorting in large area, then the PCB itself temperature will it dissolve it in air, so I think Rosen will be the best option to catch the thief.

[@طارقمحمد-خ4و]

Hello brother, how are you? Can I run the IC powered by the phone charger at 12 volts instead of 220 volts, adjusting some resistors, and what are the conditions, if possible??❤

[@pietropuleo2662]

Io uso il metodo kelvin a 4 punte e trovo subito il corto nel condensatore

[@tvbox8478]

what is it 😊

[@HaseebElectronics]

@@tvbox8478 it is 4 wire measurement system.

[@rajnishkaloi8591]

@@HaseebElectronics translation option doesn't shown, might be he is asking to use kelvin bridge method...!

[@Pozitiv_ion]

​@@rajnishkaloi8591The colleague says he uses this Kelvin method. In Italian "Io uso" means "I use". In particular, in this case, phonetically, Italian are similar with English, only in this case, in English "I use", Italian "Io ​​uso" 😃 Otherwise, these 2 languages ​​are very different

[@jluke6861]

Thank you for your videos.