Tips, Tricks to Diagnose and Fix a Hayward AquaRite salt system No Flow solid Red indicator failure light.
Пікірлер: 368
@KennyP-i7gАй бұрын
Thanks for the diagnostic tip. I used the screw driver test and it showed the flow switch failed. I replaced it with a Hayward replacement flow switch and it's working now. The video saved me a lot of time and avoided a costly service visit!
@EliteSwimmingPoolsTVАй бұрын
You’re very welcome, I’m glad to have helped you with this and saved you time and money. Be sure to subscribe to and like our channel for all new uploads. You’ll surely come across other videos that may give you more good advice and help. Thanks for watching and commenting on this video.
@carlacordoves Жыл бұрын
Solid! Was able to diagnose what I actually need without spending loads of money. Thank you so much for posting this video. Very detailed!
@stevevogel35872 жыл бұрын
Awesome! I am not a tech in any way shape or form...but I was able to watch this, diagnose, and fix the problem. So simple. Thanks!
@EliteSwimmingPoolsTV2 жыл бұрын
Your welcome. Thanks for watching and commenting on this video. Hope your a subscriber and please share this out to your friends do this video can help others.
@datushyness53502 жыл бұрын
I thank my Lord all the time for having those great people in this world to help others save money
@crumber72 ай бұрын
Wow. You saved my life. Worked perfectly and discovered it was the flow switch. I just took an old telephone cable and cut the end to reveal the wires and connected the wires together so that it completed the circuit and then plugged the other telephone jack into the unit and it tricked the card into thinking there was flow. Perfect!
@sherirsunshine Жыл бұрын
Thank you for this video. Your simple instruction on trouble shooting saved me hundreds of dollars while allowing me to resolve my issue.
@EliteSwimmingPoolsTV Жыл бұрын
Glad to help.
@SpeedcraftGarage4 жыл бұрын
Great tip! I was able to verify the switch was bad using this technique. We had just replaced the main board which legitimately failed, and then the flow switch decided to die a few weeks later, and this tip helped us verify that.
@EliteSwimmingPoolsTV4 жыл бұрын
That’s cool.
@MrSirjohnson69 Жыл бұрын
Dude! You saved me a ton of grief and have my pool generating chlorine now. Took an old phone wire, cut in half, split the wires, stripped to copper, twisted together and plugged into AquaRite. Now there's flow 🙂. Now I can relax waiting for replacement flow switch. Just have to remember to turn off generator when pump is off.
@EliteSwimmingPoolsTV Жыл бұрын
Glad to hear that.
@vickisinger85753 жыл бұрын
Thanks! You have saved me a lot of time and money by this tip. I thought that my AquaRite board had died, but it was simply the flow sensor. Again, many thanks!
@EliteSwimmingPoolsTV3 жыл бұрын
Your welcome.
@camf33Ай бұрын
Excellent.. explained in details and professionally, I did noticed one thing when I pulled mine though - noticed that no matter what direction the metal contact is facing (supposed to be face the water flow) it all rotates together when you screw the cap on, so essentially the entire housing moves which can position the metal flap in the opposite or any direction, unless mine is not well that's what it did to me. Nonetheless, after I re-screwed it worked well.
@shawnmacleod47912 жыл бұрын
Saved me a bundle! My flow wire was accidentally clipped by my whipper snipper! Repaired and back in biz! Thank you!!
@MrKlee7776 ай бұрын
The tips you told me how to deermine if the board is wrong or the switch is wrong are really helpful.
@EliteSwimmingPoolsTV3 ай бұрын
Great to hear
@Michael-gw3ki2 ай бұрын
Absolutely amazing video! Thank you for the troubleshooting tips. I had the exact same problem with a new Hayword T-9 that just installed. I used the screw driver to trick the board with the screw driver and got the blinking no flow light. That let me know that the head unit was working just as you stated. The most important tip for me was when you said make sure the flow arrows were in the right direction. Mine was not. I adjusted the direction of the flow arrows and it worked like a charm. Thanks so much.
@kathycouper90502 жыл бұрын
Great video and instructions. I successfully replaced my flow switch and all is good with my salt system - got the "generating" green light. Thanks so much for helping me save $$s.
@EliteSwimmingPoolsTV2 жыл бұрын
Your welcome. Thanks for watching and commenting
@giselefriend76962 жыл бұрын
Thank you so much for this video! Newbie here! I tried the flat screwdriver test and it blinked. I disconnected the whole connector and reinstalled. The new pool guy had screwed it into the salt cell unit in the wrong direction. Working perfectly now!!!
@ritai92723 жыл бұрын
Great video! This solved my problem and prevented me from spending money that I didn’t need to spend. Your explanation was clear and simple! Thanks!
@Shannaindexing3 жыл бұрын
Perfect video. I didn't know about the flow switch after having this system for 15 years. I found the screwdriver test made the board work. My cord had actually been cut so I've ordered a new part. Thanks so much for your time!
@EliteSwimmingPoolsTV3 жыл бұрын
Your welcome, My pleasure
@MargeBurkellDotCom3 жыл бұрын
AWESOME! I was thrilled to use your screwdriver trick to see if it was indeed the flow sensor. We had replaced our generator board a few years back so I was pretty sure and crossing my fingers that it wasn't that but just as you said.... it BLINKED! Bought the new sensor (only $30 at our local pool store) and tested it the way you backtracked to show us... yep! WORKED! Installed it in minutes and we are working again! THANKS!!!
@EliteSwimmingPoolsTV3 жыл бұрын
Your welcome
@censored7881 Жыл бұрын
This helped me a lot. I was so happy to see that little red LED start blinking when I did the screwdriver test. Thank you!
@gerardofollano84172 жыл бұрын
Thank you this helped alot, did the test with screwdriver so I knew the problem was the flow sensor, I removed it and there was hair wrapped around the tab keeping it closed, removed hair screwed it back and now works!!!
@estherhatcher6654 жыл бұрын
Thank you!!! After seeing this I checked out the flow switch wire and something had cut thru it! All spliced and now it's generating again, woohoo!!
@EliteSwimmingPoolsTV4 жыл бұрын
Keep wires zip ties to conduit/ plumbing etc. And off ground and buried.
@mmbrwn44492 күн бұрын
Thank you much. I was ready (not) to purchase another salt cell.
@pfkinto Жыл бұрын
Thank you Brother from Toronto Canada! You saved me $200. As you acknowledged… jumped the gun.. A little long if you want to gain followers but you led the way to figuring it out.. thank you!! :)
@grantwiesner74723 жыл бұрын
Thanks for the really helpful video. I followed your steps to diagnose the problem, replaced the flow switch, and now it’s working and generating chlorine again. You saved me a lot of time and money. Thank you!
@chuckschmidt7733 жыл бұрын
I did the test like you showed and the No Flow light did flash. Lead wire is still good, so definitely the sensor (only about 3 yrs old). Now I just have to find a replacement sensor. Thanks for the video and information.
@jdwilson20113 жыл бұрын
Great video thank you for the direct information without all of the nonsense other people do. You tricks to the trade saved me money! Thanks again!
@EliteSwimmingPoolsTV3 жыл бұрын
Your welcome my pleasure. Thanks for watching this video, be sure to come back and watch other videos we upload.
@colinclifton17483 жыл бұрын
You just saved me a bunch of 💸 cash! The screwdriver trick worked. Cut out the damaged part of my float switch and rewired it, and it started working again.
@EliteSwimmingPoolsTV3 жыл бұрын
That’s great, happy to hear my trick worked for you. Save that money 💵
@theofaulkner58482 жыл бұрын
Thanks your directions are super I will try this tomorrow.@@EliteSwimmingPoolsTV
@EliteSwimmingPoolsTV2 жыл бұрын
Good luck
@tonyvernola3469 Жыл бұрын
Great Video and great advise . Thanks. You may want to clean the tip of the screwdriver of rust and paint. That’s probably why you had to wiggle a bit to make contact. Thanks again.
@EliteSwimmingPoolsTV Жыл бұрын
Lol. It’s not the rust or paint. It simply because I wasn’t firmly and evenly pressing all the pins on the internal connector port.
@alparker25862 жыл бұрын
This video was excellent and helped me so much. I was able to get an after market flow switch that I bought from Amazon to work by adjusting it 1/4 turn until the NO FLOW light started to blink. Your video gave me excellent information!
@EliteSwimmingPoolsTV2 жыл бұрын
Your welcome. Thanks for commenting and watching this video.
@ericlambousy241720 күн бұрын
thank you, sir. this will help me to diagnose my dad's generator on his pool.
@Maximus091768 Жыл бұрын
You hit the nail on the head! THANX BROTHA!! You saved me at least $200. Did the crew driver test-it was the Flow Valve. $23 part from Amazon-pool store want $100. Here is my question-do I EVER PUT THE BOX ON SUPER CHLORINATE? If so, when do I do it. My pool got cloudy because the flow flow was dead an I didn’t realize it.
@EliteSwimmingPoolsTV Жыл бұрын
You can utilize the Super Chlorinate after a heavy pool usage situation.
@Maximus09176811 ай бұрын
I’m back to no flow
@bobdruzynski3882 Жыл бұрын
Thank you for this video! I was able to quickly diagnose the problem and fix it without having to call a pool company to come out!
@EliteSwimmingPoolsTV Жыл бұрын
Excellent! Your welcome
@mikey48134 жыл бұрын
Hey I did your trick and it work thanks you save me a lot of money
@brianvigness77103 жыл бұрын
Great video. Thanks. I thought I was going to have to call in a pro, but it was a very easy fix thanks to this video.
@kuma17202 жыл бұрын
Thank you!! Helped me diagnose this issue. Whew. I even tried an older switch and still had no flow. Weird. The screw driver worked to figure it out
@EliteSwimmingPoolsTV2 жыл бұрын
Great
@mregan38554 жыл бұрын
Great help.. I am 65 y and feeling confident I can replace if necessary.. Thank you
@mregan38554 жыл бұрын
Yep I tested with screwdriver.. Now have flashing light! Will replace
@billsmith89893 ай бұрын
Thanks a lot for this - definitely helped me narrow down the cause of my no flow light (Flow switch). Everything back working now
@EliteSwimmingPoolsTV2 ай бұрын
Glad it helped!
@nicholasdoveralabama2 жыл бұрын
Thank you. I found a off-brand with the same model number on Amazon for less than $30 and it worked great.
@dms1203 жыл бұрын
Thanks for this video. Saved me a lot of money. I replaced the flow switch myself.
@EliteSwimmingPoolsTV2 жыл бұрын
Good job
@BVelix Жыл бұрын
Perfect spot on tip for No Flow! Thanks!
@EliteSwimmingPoolsTV Жыл бұрын
Happy to help!
@wiregrasshumanesociety50712 жыл бұрын
Thanks so much! I was about to give up and think it was the board because I had to hold the screw driver for almost a minute before the the green chlorinating light finally came on. Yours seems to only take a few seconds.
@brittanygabrel2 жыл бұрын
Thanks to this video and your comment, in about a minute it went from flashing to green!!! I almost gave up and called in a pro, because I thought it wasn’t the sensor since it took so long! Thank you!!
@EliteSwimmingPoolsTV2 жыл бұрын
Your welcome.
@RockyStatue10 ай бұрын
Same here mine was a full minute delay til green
@Chris-xe7hq3 жыл бұрын
Very helpful. Thank you so much. I'm installing a brand new system and it's been a nightmare.
@RealMJSr2 жыл бұрын
Had this happen yesterday, turned the pump off and on and it cleared it. Now I’m thinking my switch may be going bad. Thanks!
@tnjeepyj2 жыл бұрын
Thanks for the video. I had a pack of RJ11s so I just took one and made a loopback plug to test the flow sensor contacts.
@keithguay75234 жыл бұрын
Awesome video my man.... I owe you a beer. Job went perfect I changed the Flo switch and after a min the flashing light stopped. And it said generating. In green. Ty .
@EliteSwimmingPoolsTV4 жыл бұрын
Your welcome. Keep your pool good & blue.
@danl207310 ай бұрын
It turns out the gardener dislodged the data cable and it wasn't properly seated. Didn't even have to use the screwdriver. Works fine, thanks!
@joetterolison12862 жыл бұрын
Thank You That phone type jack test You showed worked I had an old phone jack and shorted ONLY the center wires (Red & Green) to replace the screwdriver test (and did not short the Black & Yellow) It is generating now but the Inspect Cell light is Yellow I just replaced the cell back in June I am going to look at more KZbin videos and see what the INSPECT CELL light is connected too Ken in Florida
@EliteSwimmingPoolsTV2 жыл бұрын
Typically when they inspect cell light is on and flashing this is an indication for the pool owner or the pool service provider to inspect a cell in case it needs to be cleaned. If the sale is clean then simply hold the diagnostic button for five seconds and this will Reset the internal clock for the next time the cell should be inspected
@brianhassett1994 Жыл бұрын
Thank you so much! I actually found a small cut along the wire. Between the sensor and the board. I spliced the wire and the switch is working again. I'll buy a Haywood switch in the meantime
@EliteSwimmingPoolsTV Жыл бұрын
Good find.
@lupita2011g Жыл бұрын
@@EliteSwimmingPoolsTV what would happen if we put both wires simulating he sensor is close ana there is flow and leave it in that way for a while ?
@lupita2011g Жыл бұрын
I mean like a short circuit
@jpsully1 Жыл бұрын
Well this is great video. With screw driver I was able to verify unit was good and it was flow switch. But just sprayed some contact cleaner on connector terminals and inserted a few times and flow switch works again without replacing. So this does not account for dirty connector contact interface. But still was huge time saver for me since was not sure whether unit or flow switch was causing the problem
@EliteSwimmingPoolsTV Жыл бұрын
Every situation and circumstances are different and unique sir. Thanks for watching and commenting. Be sure to subscribe and watch other videos.
@WaziZam Жыл бұрын
Great video! One of the best self-help videos I’ve ever seen. Thank you so much!
@EliteSwimmingPoolsTV Жыл бұрын
Awesome, thank you!
@davidperry2778 Жыл бұрын
Yep, that's the trick. Interesting in my case is that my setup is vertical at the RJ which should not require a flow switch. Ran this system for 4 years without issue then had to replace the AquaTrol and ran into this. Now, just stuck a screw head in there and all good.
@BJ-503 ай бұрын
Either way, thank you so much for the video. My cell is clear and now I know the board is still functioning. Time for a new switch
@EliteSwimmingPoolsTV2 ай бұрын
Glad it helped
@Lord_Arn Жыл бұрын
You saved me from opening up the control panel to the circuit board.
@kathiehires74164 жыл бұрын
Good advice! I did that, and I found the same results you got. Thanks Man!
@EliteSwimmingPoolsTV4 жыл бұрын
Works every time. Your welcome.
@kathiehires74164 жыл бұрын
Is it worth a try to clean the contacts where the plug connects?
@EliteSwimmingPoolsTV4 жыл бұрын
The flexible metal piece is the contact lever and makes an internal contact inside the round part which gets screwed in. Not worth the time because it most likely would make any difference.
@user-tr9zp3lo2x Жыл бұрын
Great video!! Easy to understand and our No Flow switch is fixed.
@EliteSwimmingPoolsTV Жыл бұрын
Glad it helped!
@michaeloyarzun56312 жыл бұрын
Good video, followed your advise and solved my problem. It was the flow switch. Thanks
@EliteSwimmingPoolsTV2 жыл бұрын
Your welcome. Glad my video solved your problem. Thanks for watching & commenting, Hope you are a subscriber and please share this video out so I can help others
@papagigo13 жыл бұрын
You saved me a lota time,, it was the flow sensor ! Replacement cost was a staggering $82.00 !!
@SpookyEng13 жыл бұрын
You just saved me a ton of time and money. Thanks!!
@EliteSwimmingPoolsTV3 жыл бұрын
Your welcome, thanks for watching. Subscribe for more time & money saving tips
@dougmitchell8333 жыл бұрын
Great video and thank you for putting this info out on the web!!!
@bettynuce45293 жыл бұрын
How to test your cell
@Bonddeeee Жыл бұрын
Worked! Got a $20 replacement. I had thought I needed a new cell since I think I submerged the whole cell I'm acid solution to clean and it stopped working. I think the residual acid that was in the cell must've hit the sensor and messed it up
@UGLEE11 ай бұрын
Excellent video. Everything worked perfectly. Thanks very much for your expertise.
@GrantsDaddy3 жыл бұрын
Thank you! Flow switch dies after14 years, saved me from ordering a new panel. Great video. Cheers!
@EliteSwimmingPoolsTV3 жыл бұрын
Your welcome
@FLmetalhead Жыл бұрын
Finally a video that I learned something.
@EliteSwimmingPoolsTV Жыл бұрын
Awesome to know. Thanks for watching and commenting
@silverjava1one971 Жыл бұрын
It worked. Thanks for your help. May the KZbin algorithm be in your favor.
@EliteSwimmingPoolsTV Жыл бұрын
Very much appreciate your comment and thanks for watching. Hope you subscribe to this channel
@scottscott530111 ай бұрын
THANK YOU!!!! You saved me a ton of money. Great job!
@cmcstm3 жыл бұрын
Thank you for your excellent video tutorial, I was able to fix this by myself. I actually had the new flow sensor from purchasing the replacement cell 3 years ago, so I was able to fix right away. Thank You!!!!
@elliscameron50583 жыл бұрын
pro tip: watch series at flixzone. Me and my gf have been using it for watching all kinds of movies lately.
@zahirsonny76893 жыл бұрын
@Ellis Cameron yea, I have been watching on Flixzone} for since november myself :)
@billcalabrese911 Жыл бұрын
Thank you for the excellent information and saving money.. I ordered a new flow switch.. 👍🙏🇺🇸
@stucookson70224 күн бұрын
The test worked great, thank you!
@lancejones64202 ай бұрын
Thanks so much for your video ! Very informative and very professional !
@EliteSwimmingPoolsTV2 ай бұрын
Glad it was helpful!
@Black02wing9 ай бұрын
Helped solve my problem ordered new switch and replaced. Thanks
@bobrustigian4637 Жыл бұрын
Thank you so much for this video! You saved the day!
@fernandbourgeois87293 жыл бұрын
Great video. Learned a lot from this. Changed my flow sensor and system working ok now. Thanks for the tip.
@kencheesman18287 ай бұрын
Awesome video. Thank you! Hope the mosquitoes weren’t too bad!
@EliteSwimmingPoolsTV3 ай бұрын
Wow the mosquito thing was a big thing huh 🤔 😂
@peterclemmet Жыл бұрын
Excellent explanation, well done very helpful
@committed2thecore2 жыл бұрын
Excellent video. Just saved me a ton of money
@zeusgsxr4 ай бұрын
Was I the only one fixated on that mosquito? It was on his face, hands etc. Those things give me welts. 😂
@CJ-lj9fb2 ай бұрын
Thank you! You just saved me a service call!
@georgebostick63373 жыл бұрын
Excellent tip! Thank you for sharing.
@EliteSwimmingPoolsTV3 жыл бұрын
Your welcome
@mikelawrence83082 жыл бұрын
Thank you! Great tip, makes perfect sense.
@EliteSwimmingPoolsTV2 жыл бұрын
Your welcome
@johnmorrison55553 жыл бұрын
Thank you for that tip! Flow switch on order!
@EliteSwimmingPoolsTV3 жыл бұрын
That’s great to hear. get your system back up and running again. Hope your a subscriber?
@billniarchos7585 Жыл бұрын
thanks! I have no flow indication. will check shortly!
@EliteSwimmingPoolsTV Жыл бұрын
Let us know what you find.
@brucesears982 жыл бұрын
Very helpful, solved my problem. thank you
@EliteSwimmingPoolsTV2 жыл бұрын
Your very welcome. Thanks for watching and taking the time to comment, much appreciated. Hope you are a subscriber and please share this out. The more shares the more our videos can help others like yourself.
@samshicks4382 Жыл бұрын
This Hayward system is nothing but trouble for me. Expensive and nothing but troubles.
@TT-hv8bx Жыл бұрын
Nothing but trouble. ! Not happy.
@FLmetalhead Жыл бұрын
Me too
@lauraepperson5786 Жыл бұрын
Same here!
@miamicyclist014 жыл бұрын
Great video troubleshooted exactly liked you showed. Thanks for the tip!
@EliteSwimmingPoolsTV4 жыл бұрын
No problem. It’s all about the Knowledge!!
@JorgeGonzalez-m9yАй бұрын
Outstanding, thanks for the info.
@jeanfrancoisroy17792 жыл бұрын
Greatly appreciate your help
@EliteSwimmingPoolsTV2 жыл бұрын
Thanks for watching and commenting
@MHHamm2 жыл бұрын
Omg you are my hero right now!
@EliteSwimmingPoolsTV2 жыл бұрын
Thanks
@cafdds2 жыл бұрын
Thanks for the tip. Bad switch was all it was...
@EliteSwimmingPoolsTV2 жыл бұрын
Nice
@dirtybones611 ай бұрын
Thank you! Saved me a ton of money
@jackforester734 жыл бұрын
Thanks for the tips. I wanted to add that Hayward recommends 12" of straight pipe before the flow switch. I'm assuming this is to help with tubulance that may interfere with proper flow switch activation. The salt cell counts towards that 12", so I'm not sure why they chose to install it in that hard to reach location, rather than after the salt cell, but clearly it still works, even innstalled so close to that elbow. Again, great video.
@EliteSwimmingPoolsTV4 жыл бұрын
Thanks, and thanks for watching.
@peterpeter8086 Жыл бұрын
Thank you for the knowledge.
@EliteSwimmingPoolsTV Жыл бұрын
Your welcome
@chadroth2722Ай бұрын
Very helpful. Thank you 👍🏻
@josephfusco87452 ай бұрын
This video was extremely helpful. But I have the same question as another post. If there is no flow does that mean chlorine is being generated?? Thank Joe
@RaphaelLacoste11 ай бұрын
Thanks a lot for this video ! quick question, I turned off the filtration and closed valves, but I still have a geyser when I unscrew the flow switch... how can I make sure the water will not evacuate strongly despite all the valves being closed and pump turned off ?
@Itsjillski2 ай бұрын
Great instruction!!
@BParsons Жыл бұрын
Excellent video! Thank you so much!
@EliteSwimmingPoolsTV Жыл бұрын
You're very welcome!
@wpulman2 жыл бұрын
great video I will replace it now
@EliteSwimmingPoolsTV2 жыл бұрын
Thanks for commenting and watching. Be sure to subscribe
@mikejulson682 Жыл бұрын
another reminder of why my pool is a nightmare.
@EliteSwimmingPoolsTV Жыл бұрын
It all can be fixed and get better
@robertmontagnese3 жыл бұрын
Thanks a million. This was very helpful.
@garyhenry1443 жыл бұрын
Thanks for tip, very helpful
@EliteSwimmingPoolsTV3 жыл бұрын
Your welcome. Thanks for watching this video, be sure to watch other uploads we have.