Helmet Safety Light Installation | Steelmate H3(Step-by-Step)| Motorest See You

[@TheJordanJ]

Thanks for showing the different modes

[@dingpongcrate]

Different modes are good to have when it comes to safety

[@BilboBaggins-q8k]

Thank you man it’s because of you making this video I can better gauge if it is for me and I like what I see the operation and the ease of install most of all the safety

[@dingpongcrate]

Glad that I can be your assistant.

[@jeffbroemmel8003]

That's very cool. Nice piece of kit.

[@dingpongcrate]

Thank you, I have had it for one year. so far many drivers can see me:)

[@oakie10]

Very nice to have!

[@dingpongcrate]

Well. Thank you.

[@33monche]

Thank you for your video. I installed this unit and the brake light works perfectly. The indicators don't register on the light unit. I have tested and it has power on the indicators. Is there a certain way of programming the ecu to register the indicators?

[@dingpongcrate]

I’m little confused when you say indicator. LED display on your helmet? If so you should have stop, left and right signal. There is no programing

[@33monche]

I mean left and right signal ​@@dingpongcrate

[@dingpongcrate]

@@33monche you might want to check the wiring. make sure to connect the right color code wire from your bike to your helmet

[@dingpongcrate]

Did you get to fix your signal problem?

[@33monche]

@@dingpongcrate not yet, going to give it another try tomorrow. Will let you know how I get on

[@confederateredskin]

Nice video.

[@dingpongcrate]

Many many thanks

[@bsheen]

I have bought two units and both will not enter pairing mode. Instructions are terrible. Did yours come paired? or did you have to pair it?

[@dingpongcrate]

I know instruction is terrible. I had to figure it out. For me, it just paired when I connected the correct wiring. What kind of bike do you have? I’m still riding my bike and still works great

[@bsheen]

Kawasaki Vulcan S

[@derikquach7134]

I have a hard time getting it into pairing mode. I followed the listed instructions with no luck. Any tips? thx!

[@dingpongcrate]

ECU programming (For H3) ACC ON, press the switch button 3 times in 3 seconds, and press the switch button at the last time until the blue light is on, then enter the programming mode ： Press the footbrake and the green light will be on to indicate the programming is done successfully.

[@ToyMaestro]

is there anyway NOT have the runnn lights and jus have the brake and turn signals on? here in California I cant have anything flashing

[@dingpongcrate]

There is about 8 running lights mode you can change. Just signals and stop lights don't have. There are nonflashing horizon lights that have an amber color and red lights

[@iritian]

Thanks for the video! How is it long term? Do you still use it?

[@dingpongcrate]

Thx for watching. I still use it for the commute. It's been a year half. Still works great

[@iritian]

@@dingpongcrate that's great to hear. I bought the H2 version to use on my ebike. It's been great so far

[@dingpongcrate]

on a ebike? wow that's a wonderful. i would love to know how you hooked up@@iritian

[@iritian]

@@dingpongcrate No wiring needed! The H2 uses a gyroscope instead of connecting to an ECU. Unfortunately it doesn't have the turn signal feature.

[@dingpongcrate]

dang. turn signal would have been nice. thx for telling me. Be safe on the road @@iritian

[@YooperDanKulka]

How long can you keep it on where's the plug in usb?

[@dingpongcrate]

about 4-5 hours. USB is inside where the magnetic mount and wheather seal