2004-2008 Ford F-150 ac compressor replacement

[@Matthias53787]

Thanks for getting the close-up shot of the connector. That's what I needed.

[@williamshemendera2378]

This guy is great. Followed him step by step all the way through. Good job my man. Thank you very much

[@SamMobleyLiving]

How hard is this really?

[@HelpingHandAutoRepair]

Hardest part I think is blindly removing the ac line bolt. Aside from that it’s pretty straightforward.

[@ericfairchild2973]

This was the best explanation and example I've found. I only have an issue with the "prism" (ac manifold hose) but I needed to fully grasp a bit more of the system so I stayed the whole time

[@erictownsend8711]

That is a FANTASTIC VIDEO. vERY CLEAR CAMERA WORK AND PROCEDURES VERY WELL EXPLAINED. I learned a lot about the proper tools that are needed to do the job. I'm headed outside RIGHT NOW to start dissassembly so i can now replace the AC compressor in my 2006 Mark LT truck. Thank you VERY much for sharing your knowledge; it will save me a TON of money. PLEASE make more videos like this (about 2004-2008 F150) I have subscribed.

[@Khylur_Getz]

On most Ford's there is a sticker with a diagram of the serpentine belt routing that's attached to that first plastic shroud that you removed which covered the frame/radiator mounts.

[@DCurzio]

I wanted to comment and thank you for this really great, well done video (as well as the dryer video). A couple of things I wanted to bring up that I noticed. #1 I left the bracket on by the power steering pump but removed the upper radiator hose. Felt that was easier. #2 This is clearly a 2WD vehicle. The 4WD is a bit harder as the shaft is in the way #3 Getting the compressor lines unbolted were a bit harder than it appeared here

[@JerryWDaviscom]

Great camera work and explanations. Liked and sub'd.

[@rickbarger5161]

Thanks for the video very helpful.I was gonna send it to a shot , but i'm pretty sure I can handle that

[@Richard-4940]

Awesome video man. Super helpful. Thank you for showing step by step

[@joses.salmeron4181]

Thank you for your hard work and the teach us how to do it I really do appreciate it

[@jorgetoloza269]

Great video, explained thoroughly...thanks..

[@markk7075]

Excellent video!!! Thank you! If youre keeping your f150 for a while do yourself a favor and cut your fan shroud in half(driver side and pass side) horizontally. Drill holes and zip tie when replacing .Then you only need to remove the small bolts holding the fan on.

[@GreenMachineXXII]

For the fan clutch i highly recommend the lisle 43300 pneumatic fan clutch removal tool or something similar comes off so easy with a air hammer

[@frankgonzalez534]

Thank you for your video very informative!!! Know I just need to add freon😂 any videos on that? Thanks again just completed the install.

[@HelpingHandAutoRepair]

I don’t have any videos adding Freon. I don’t like any of that canned crap from auto parts stores. By the time you end up paying $60 (or more) for some Freon in a can. You could have had a proper AC shop charge your system properly. More importantly they will advise you of any leaks you could have (most people have leaks) and point you in the right direction as to fix the leaks. This way you don’t have to keep buying cans (see:wasting money) to keep charging it up.

[@ctb2814]

Why did you remove the fan and shroud if the ac compressor come out from the bottom.

[@HelpingHandAutoRepair]

I had other things to do on this truck as well. You could probably do this job without removing the fan shroud, however while under the truck, I found it much easier to reach around the front of the motor to get the ac line off as well as being able to have a correct range of motion for the ratchet on the upper bolt.

[@210GrainsOfJustice]

Gotta swap mine out 2006 king ranch, looks easy.

[@delliott777]

I support removing the Fan and Shroud. The exhaust manifold is in the way, and I am more worried about getting debris in the new one. The compressor won’t come out from the bottom with the AC lines attached. So, the time and place of installing the hoses to compressor can reduce risk of getting dirt inside. I’m in the midst of doing this job, now.

[@HappyJF]

If you have a 4x you need to remove it through the fan shroud

[@michaellopez4018]

You will need the extra room to disconnect the high low lines on compressor. As well as the electrical harness.

[@ferrarimobileco5147]

Great job! Seems sort of easy, im about to do the same on a 04 explorer with a 4.6L V8 4x4, from what I’ve seen on other videos does the ac compressor need to be oiled? And is it really necessary to vacuum the lines/compressor after installing the new ac compressor?

[@tommello9525]

Great job

[@lanceanderson5898]

I couldn’t get a ratchet on mine due to the exhaust manifold or a wrench because the bolt is inset in the block. I put the socket on the bolt head and I couldn’t get my finger between it and the manifold. Any suggestions? 2006 4.6 4wd.

[@lanceanderson5898]

1/4” ratchet

[@treydinatrent]

Good video, but I hate to tell ya, I have done several of these, and all of them I pulled them from underneath, especially if it is 2wd.

[@krisnickfffs]

Is it impossible on a 4x4?

[@jasonpastor6315]

I tried all size ratchet’s and wrench 🔧 and couldn’t properly fit them on that top bolt that goes in between the ac lines because of the exhaust manifold. Do you have any other idea or way I could take it off because I really don’t want to have a mechanic do it for me and I want to save myself some money .

[@robertkennedy1666]

I'm having the same problem I'm going to try to use an impact... Socket keeps slipping off at that angle

[@HelpingHandAutoRepair]

No impact. I used a 1/4” ratchet with a short socket.

[@hgallegos915]

My buddy helped me do it…. Its a HELL of a job… we had to use extensions , skinny hands…. Pain in the…..

[@Thatsrealnice]

That’s real nice thank you

[@sintruder]

Tip for you from an old mechanic, take your fan, and shroud out before doing anything with the belt. The belt, and pulleys are a million times easier with the shroud, and fan out of the way, plus the water pump wont spin with the belt on it. Doing the belt first saves you no time, just makes things more difficult.

[@anthonytrodriguez7166]

Cool and easy procedure

[@rwes2940]

Do you have to evacuate the ac system?

[@HelpingHandAutoRepair]

Yes, unless you know the Freon has all leaked out and the system has no pressure anymore.

[@jeanbernardjoseph09]

👍 you are the man excellent job

[@bennettwallace6004]

Do you remember the specific reason the customer wanted the AC compressor and dryer replaced? I just finished a timing job and now in the middle of changing out the passenger exhaust manifold and had the dryer and compressor pulled to gain access to everything I needed to do. I'm wondering whether to change out these items as preventive maintenance or just go with - if it's not broke why fix it. Thanks

[@HelpingHandAutoRepair]

His compressor seized up. Makes sense to replace both.

[@raphaelroberson1129]

Great video, very detailed for removal. I think you removed too much the ac is basically under the right front wheel well. I think I can do this one. You didn't feel the need to replace the hose ?? Do you have any concerns about what's left over in the lines ? Having more to do explains taking more off. Any concerns about the Condenser?? .

[@juniorpenalozasaucedo9464]

Can the ac compressor cause a coolant leak around the same area?

[@HelpingHandAutoRepair]

No. Coolant is not present in an AC system.

[@livegooddad]

What hole do you put the oil in? Also did you have to depressurize the system if so whats the best way to do that? Im confident I can do this job but idk really what you need to do for these steps and can you just replace the compressor and fill it with freon and good to go or do you need that whole ac set thing you check high and low with?

[@HelpingHandAutoRepair]

Ac evacuation and charge should be done at a professional shop. That’s where this truck was.

[@StayingBack71]

​@@HelpingHandAutoRepair So how is somebody saving money by replacing the compressor themselves, If they have to take it to a shop to drain/fill the system and pay whatever $500? Where's the DIY Savings at? that makes no sense. Guys that are watching this video want all in DIY to save money and they're gonna put it in the atmosphere if they have to save money

[@HelpingHandAutoRepair]

I mean no one is stopping you from doing that right? If an ac shop is charging you $500 to drain and refill your Freon. Who is the dummy? Them or you? That is an absolutely absurd amount of money to evacuate and charge the ac system.

[@StayingBack71]

@@HelpingHandAutoRepair That price of $500 is just an example, I guess it's the point im making, Even if it's $150 If you gotta take it in, you Might as well spend the other extra 2 hours and have them replace the compressor too. I have always praised people that are thrifty or on a budget If you go to tackle a project you're in 100%, or you're not gonna save any money.or make much if a difference.

[@livegooddad]

Well to give an update my compressor blew so was no Freon in the system I got another compressor put oil in and added freon good to go been going strong for awhile now with no issues and yeah probably did save myself 500 or more dollars doing it myself

[@Cam-wi3tp]

i have a 2003 lariat f 150 and i wish my bolts were this easy to get to....

[@trilldawggy4544]

Thanks. Seems totally unnecessary taking the fan and shroud off. Also did you fill and cycle oil in the new compressor? The tractors i work on come filled with pag oil to spec. But passenger vehicle compressors come dry and will lock up after 30 sec if installed dry

[@biglazybilly]

take belt off comp,and unbolt comp

[@Austinshook97]

Can anyone explain to me how I get the electric sensor of the nut I can’t get anything on the 36 mm nut without taking it off and it doesn’t seem anyone shows how to do this

[@HWoodCreations]

What about the refrigerant? Do you have to drain the system before removing the lines from the top of the unit? Thanks for the video.

[@HelpingHandAutoRepair]

Yes.

[@HWoodCreations]

@@HelpingHandAutoRepair How involved is that?

[@HelpingHandAutoRepair]

I don’t have an ac machine so I took it to my buddies shop to have him evacuate the system. Any auto repair facility should be able to perform that for you for a fee of course.

[@furious4203]

​@HelpingHandAutoRepair when did you get it flushed before or after replacing the compressor

[@HelpingHandAutoRepair]

Evac the system, replace the compressor, recharge system.

[@donaldlord9596]

hey i am just woundering where can you find those bolts at cus mine is all rusted and one broke and all i need is those bolts can any one tell me or give me a link to order some i have a 2005 ford f150 fx4 5.4

[@HelpingHandAutoRepair]

Go to a local fire dealership. Best way

[@jordanleonard5534]

Thanks for the awesome videos. However I have a ac related question. I installed the new compressor and dryer. The compressor clutch won't come on. I can jump the relay and it comes on. Bought new relay and it won't kick on with relay. Anybody tell me why?

[@HelpingHandAutoRepair]

Did you recharge the system?

[@KyleBoydBrappinboyd]

Put the top bolt in first . Then try it might help

[@jesuscasassr5562]

Thank you.

[@tmartis93]

Does this also apply to a 2004 expedition 5.4? Great video btw 🙏🏽

[@HelpingHandAutoRepair]

It may be similar.

[@pakosuarez11]

U can use a rachet an a strap to pull it

[@leslie9271]

engine size?

[@hgallegos915]

We had to loosen the fan shroud. It went out trough the top.

[@rockerbigjoe5711]

Is this a 4×4?

[@lazzjayymedia2953]

Not at all. If you have a 4x4 you will not be able to remove it from the bottom. Loosen the 3 bolts and pull it out from the top

[@AlphadogFJB]

Is it a 5.4 or 4.6?

[@HelpingHandAutoRepair]

5.4

[@gregporter6299]

What brand compressor did you buy? Did you replace the condenser?

[@HelpingHandAutoRepair]

Customer bought one from autozone I think. I replaced the ac drier and expansion valve.

[@gregporter6299]

I ended up buying a full kit with compressor, dryer, hoses, condenser, etc. made by UAC. I have a lift and installing the compressor with the manifold was a royal PITA! I ended up installing the manifold on the new compressor first then slid the assembly into position from the front. Good video. It helped a lot.

[@frankcabrera3710]

You can remove just the large plastic intake that runs from front fender to air filter housing. No need to remove everything, the first 15 min of work are unnecessary

[@shockerfilms]

That's what I was thinking. I've replaced countless of these and all you have to do is loosen the belt and drop it out the bottom.

[@juliuseckles6037]

Great job 💯

[@leslie9271]

5.7L?

[@HelpingHandAutoRepair]

This is a ford. So it is a 5.4 triton

[@aurellioroccone2150]

Do it underneath flip over the cover remove the fan compressor 3 bolts align the screws and it's out

[@nicholasthompson1215]

I don't think all shrouds fold up like that lol I know what you're saying though its nice

[@Snceday1]

You didn't tighten the bottom bolts

[@HelpingHandAutoRepair]

They are definitely tight. Not sure why I wouldn’t tighten them.

[@BABY_BETLOG]

4x4?

[@HelpingHandAutoRepair]

I honestly don’t remember. This is a customer’s car.

[@lazzjayymedia2953]

Nope

[@Dudemieser]

This is old But the thing comes out without all this bs

[@RobertoLezama-lw5tj]

En español

[@LoganDidItYT]

Out there ruining white shirts like it doesn’t matter. I see you.

[@HelpingHandAutoRepair]

Lol, my work shirt of choice is a white tee.

[@HelpingHandAutoRepair]

I just filmed my first video for my new channel. Look out for that soon. It’s more along the lines of what you got going on. A journey with my cars and me of course.

[@LoganDidItYT]

@@HelpingHandAutoRepair yes! Keep me updated on that!

[@HelpingHandAutoRepair]

@@LoganDidItYT will do. The channel is Knownworldwide (all one word) also my gaming handle if you’re into such things 😀

[@lewisdriver9111]

He did a lot of unnecessary work

[@Khylur_Getz]

Criticizing without offering suggestions. Reminds me of an old foreman whose dad was the boss, but the guy didn't know how to do anything except sit in the truck and play Candy Crush. There are soo many amazing sketches of him performing lewd sexual acts on OSB now covered by drywall in many of Richmond's finest apartment complexes. Is your name Lewis Hardesty by chance? 😂