High Quality Mini Spot Welding

[@scottfrazer8376]

The transformer is only needed to RECHARGE the parallel capacitors. The factor that enables welding is the OVERALL CAPACITANCE (or number of capacitors in parallel) and the size or gauge of wires feeding your welding electrodes, which should be AT LEAST 8AWG with copper tips for best results. Using a smaller 2A to 3A transformer and smaller diodes will simply take a little longer to fully recharge your capacitors, but it will still work. Any transformer from 3 Amps to 30 Amps will work just fine. Bigger transformer and diodes will simply recharge the capacitors faster. You should use a switch for charging up the capacitor bank, then switch the charging circuit OFF. Then use a fast heavy duty starter solenoid relay (or solid state relay) to trigger the welding current from the capacitors to the welding electrodes/tips with a momentary push button switch (or foot pedal switch) to trigger the relay. Also, that full wave bridge rectifier will cut your charging current from the transformer to the capacitors in HALF. Better to just use a simple quarter wave rectifier on each secondary from the transformer. A single 6 Amp diode on each secondary wire will do just fine to charge up those capacitors and you will get the FULL CURRENT from the transformer, which means you will recharge the capacitors faster. Very good basic concept here, but with many design flaws and refinements needed. You need AT LEAST 8 or 10 of those 3300uF capacitors to store enough current for reliable and consistent spot welding.....KB1BBY/Scott

[@pradeepkumarjadhav2949]

Hey Scott can u provide me with a schematic diagram for a spot welder pls?

[@untungsuharto7991]

Yes you are right... 👍👍👍

[@denis05500]

Bridge converters are different currently! You can use 50 amperes and it will not cut it anymore! And I also look at anyone in testing different capacitors -there are other types that are used in asynchronous engines -the effectiveness of 100 percent in comparison with barrels!

[@anthonyvolkman2338]

I fully agree, I use a lipo battery bank with a constant current source so I can charge the caps without a huge inrush current. Also if the circuitry that disconnects the battery from the caps fails it's current limited to 5 amps. It can also change the current according to the SOC (State Of Charge) of the caps. Mine is for portable use though and is designed to weld very thick nickel strips. It's for building all my big batteries for my scooters, portable inverters, power walls and also for car audio use. Such as my 200 ah LiFePo4 battery bank.

[@electroo-light]

I agree with you

[@stibis5713]

a spark can melt the surface but cant weld 2 pieces of nickel plates... you have long nickel strip for testing but you never try to weld them because it wont work lol

[@AshishVerma_Awesome]

yes correct it only give spark

[@RafiqExperiment]

Absolutely right ▶️ Everyone Please Watch my Videos ▶️ Rafiq Experiment

[@Zerpentsa6598]

Agree. Get a proper spot welder.

[@bobbygravina8096]

YOU DIDNT TRY IT ON A BATTERY? SHOW IT. SO WE WILL BELIEVE ON U

[@wasiskendang5218]

betul,karena itu hanya sebuah rangkaian power supply

[@benchannel5758]

creatif mantap bro

[@JaviersDIY]

For better understanding please use the universal language

[@tariqaziz4798]

زبردست

[@JaviersDIY]

For better understanding please use the universal language

[@budisantosochanel]

ijin nyimak gan

[@JaviersDIY]

For better understanding please use the universal language

[@budisantosochanel]

@@JaviersDIY permission to watch and study this tutorial

[@raulbotero982]

Excelente video.

[@JaviersDIY]

Thank you sir

[@EddieFox]

Good job. I think I would put a little current limiting resistor before the bridge tho.

[@GihansEarthmovers]

Can it weld two of 0.5mm metal sheet together ???

[@ShareTechCreative]

Good work

[@JaviersDIY]

Thank you sir.

[@刘老爷-k9q]

厲害了，，，讚

[@JaviersDIY]

Please speak in English for a better understanding

[@Pops180]

It's not going to be able to weld 2 nickel strips together. 1) you can't store enough energy in those capacitors. You need about 10 to 50 joules of weld energy. By the looks of those capacitors, you are way short of that. 2) the ESR of those capacitors and the resistance of your welding electrodes is way too high (switch to ultracapacitors of at least 100F and at least 8awg wire with proper crimp lug connections). You should target a total circuit resistance (including capacitors) of 6mOhm or less. 3) you need to apply a good amount of pressure with the welding probes prior to starting the weld. To do this, put MOSFETS or a big relay in series with the negative electrode. This will allow you to press down firmly before the weld starts.

[@JaviersDIY]

It's a brilliant suggestions . Thank you sir.

[@ayamhitam9794]

@@JaviersDIY it's not suggestion, it's a correction of your work, 😁

[@bonghoonkim5498]

never working Don't tried

[@marcbaflast7271]

Très intéressant. Beau travail.

[@JaviersDIY]

For better understanding please use the universal language

[@electroo-light]

I agree with you

[@sharukhmatekuki5830]

Very nice 👍🏻👍🏻 🇮🇳 Kuki 29|05|2022

[@JaviersDIY]

Thanks

[@electroo-light]

❤❤❤❤❤❤❤

[@kishanprasad6536]

🙂🙂💚💚💚👌🏻👌🏻👌🏻👌🏻

[@vgrmission5512]

Super 👍

[@ReelSpider]

I can only assume that it doesn't work, or you would have shown joining two strips together, rather than just making marks on a single sheet.

[@ronnygarcha]

Never gonna work.. people post anything just for likes/comments

[@ronbates9677]

I have to assume this is a work in progress?

[@juanhernandez1238215]

Since it’s such of “high” quality I want to see you use it to weld some nickel strips onto some batteries to see how good it is ok ? Please 😀

[@sandiptobose2160]

I betcha that apparatus he made can't even spot weld aluminium foil paper

[@wasiskendang5218]

😁😂🤣

[@electroo-light]

I agree with you

[@electroo-light]

❤❤❤❤❤❤❤

[@Samuel11883]

Good method but Value of the Bridge Rectifier not mentioned

[@JaviersDIY]

I attached it on the video sir

[@frankpitochelli6786]

Nice video, but...I highly doubt it could weld anything. If it does, then show it doing so..!!

[@nicasiosanchez1621]

Looks good, it would have been great if you told us the name of each part so we can buy it .

[@electroo-light]

I agree with you

[@electroo-light]

❤❤❤❤❤❤

[@syednisar3342]

Hello there...!! Will it work for Lifepo4 battery as well

[@benkperogi9534]

What is he value of all the components used?

[@JaviersDIY]

boss, I think I put it on the description box

[@njfulwider5]

Do you have a video of actual testing? Would love to see this weld. To me it don't look that strong. Would also like to see it connected to a amp meter. Typically 200 to 400 amps is the sweet spot when welding with a transformer. Great concept 👍👍👍

[@electroo-light]

❤❤❤❤❤❤❤

[@erlangenemutya263]

Have you tried on battery 18650?

[@electroo-light]

I agree with you

[@luiscarvajal3456]

Muy bueno ese rectifidor diodo no tiene mas descripcion

[@JaviersDIY]

For better understanding please use the universal language

[@nirmalkumardebnath3218]

Please quote of the transformer capacity. 18 volt = ? ampere.

[@JaviersDIY]

The transformer that I use sir has a current output of 3.5

[@ankurkhatri4]

How to increase power

[@JaviersDIY]

Just use a transformer with a high current output sir

[@ankurkhatri4]

@@JaviersDIY all other components are same? currently I use 1A in pure copper For increase power can i use 3A transformer

[@JaviersDIY]

@@ankurkhatri4 yes sir. You can use that one. But rest assured that the voltage is low compared to the current output.

[@abuthahirgeditz]

Bridge Diode Number.Thanks For Your Great Idea

[@JaviersDIY]

You can use Bidge Diode with a higher ampere sir. But the diode I use is 6A only. Thank you

[@abuthahirgeditz]

@@JaviersDIY Thank You Sir.

[@numesan-aewnua]

ทำไมไม่เชื่อมสองชิ้นให้ดู

[@JaviersDIY]

For better understanding please use the universal language

[@numesan-aewnua]

@@JaviersDIY Google Translate please.

[@albulambot2983]

Output of transformer is 12volts?

[@JaviersDIY]

18VAC sir

[@DuyNguyen-kt6jf]

K có tụ 50v mình dùng tụ 25v3300 đc k vậy

[@JaviersDIY]

For better understanding please use the universal language

[@jjj0nathan]

you did not weld anything, just made some spots, how does that help ?

[@kaisskaissi9314]

هذا العمل للنظر إلى الشرارة فقط

[@JaviersDIY]

Please use the universal language fir better understanding

[@kaisskaissi9314]

@@JaviersDIY إنها اللغة العربية اشكرك

[@cornelisganur6665]

Very interesting..would you please wrire the detail Components in this project?

[@JaviersDIY]

I put it on my description sir

[@RixtronixLAB]

Creative video, thanks :)

[@electroo-light]

❤❤❤❤❤❤❤

[@albulambot2983]

Capacitor what volts?

[@JaviersDIY]

50V sir

[@tranquilinoenerio4124]

Yes correct he is just showing the spark but not to joint the two plates it is not good.

[@mixedvlogs6503]

why you didnt try to spot a two pieces of tabbing wire so you can prove that it is work

[@macky739]

Transformator berapa ampere ?

[@intanaulia5881]

Bg ini tidak bisa nempel dari nikel ke baterai ya?

[@JaviersDIY]

for better understanding please use the universal language

[@intanaulia5881]

@@JaviersDIY can use the battery?

[@youcefgheddari8400]

Very excellent work. My question is, are the capacitors connected in series or parallel? Thank you

[@JaviersDIY]

In parallel sir.

[@wasiskendang5218]

😁

[@gtek34]

How many millimeters can it weld?

[@indraartowidodo9759]

Bridge diode code ?

[@JaviersDIY]

It depends on you sir

[@indraartowidodo9759]

@@JaviersDIY not have code

[@indraartowidodo9759]

@@JaviersDIY what amper for 18 0 18 transformer

[@indraartowidodo9759]

@@JaviersDIY what can use DIODA BRIDGE MAXIMO QL 100A 1600V

[@ankurkhatri4]

I use 3A transformer Still not working proper please suggest change components.

[@JaviersDIY]

Make sure sir that the output voltage is low while the current is high

[@keydiekazuya4797]

Try to connect with welder 2plate....

[@marioantonioardilesgabanch6647]

Y por qué no prueba soldando 2 chapas? Seguramente no tiene fuerza

[@JaviersDIY]

For better understanding please use the universal language

[@anuragbiswas5612]

Diode no kiya hai

[@JaviersDIY]

for better understanding please use the universal language

[@ajtech2990]

Transformer amps how much

[@JaviersDIY]

3A sir

[@ajtech2990]

@@JaviersDIY thanks sir

[@JaviersDIY]

Your pretty much welcome sir

[@parveztirandaz9291]

Not a spot welding machine this is a small spark machine lol

[@myungheungchoi5301]

슈퍼 캐패시터를 사용하면 가능합니다. 두꺼운 전선을 사용하세요.

[@JaviersDIY]

@myungheungchoi5301 for better understanding please use the universal language

[@raffaelebarlotti9017]

Hi, I built the welder but it doesn't work well, how many Amps is your transformer? Thanks.

[@JaviersDIY]

You need to have a transformer with a huge current sir to make it effective

[@wasiskendang5218]

😂🤣

[@electroo-light]

❤❤❤❤❤❤❤

[@alfonsoalianza5513]

did not show on two plates if it will be welded

[@ВладимирНикитин-г2и]

Для чего нужны точки на полоске жести? Может ктойнеть пояснит.

[@JaviersDIY]

For better understanding please use the universal language

[@Посейдон-й7ж]

это точечная сварка, что бы паять что нибудь, например 18650 батареи.

[@JaviersDIY]

For better understanding please use the universal language

[@andricommunity4133]

Hi friend,this what song title🙏

[@cahayu2865]

Itu pakai trafo apa kak...

[@JaviersDIY]

For better understanding please use the universal language

[@usmankiyani9087]

how many voltage and ampare of bridge rectifier you use?

[@JaviersDIY]

240V/5A

[@adielsomsantos3231]

Faltou o código do retificadora de corrente mostra na tela 🤔🤔🤔🤔🤔🤔🤔🤔???????????

[@JaviersDIY]

For better understanding please use the universal language

[@jaguricommunication9086]

Bad results showing... Spot between two strip... then it successful

[@antonioorlandoliberal3404]

i whant see the weld batery and not only the nickel , sory but my ingles is not very good , tanks . ANTONIO LIBERAL

[@VolkanASLAN-M]

It's just point on the metal plate... Where is the battery test ? Where is the weld durability ???

[@tSingh-ku7oj]

Bhai काम भी kr rha hai ki nhi ki bs चिंगारी dikha rhe ho

[@JaviersDIY]

For better understanding please use the universal language

[@සුමිතුරුමිතුරෝ-ශ7ඛ]

Is it safe?

[@JaviersDIY]

Yes sir.

[@budipurwanto8487]

trafonya berapa ampere

[@JaviersDIY]

For better understanding please use the universal language

[@علیرزم-ف9ز]

Ok

[@wahyuknwn2422]

Diodanya ukuran berapa

[@patrasgill6315]

Ji salam alaikum bhai kya हाल-चाल hai ठीक-ठाक hai kitne ka banta hai

[@JaviersDIY]

For better understanding please use the universal language

[@zona-de-pruebas]

Cómo se supone que funciona eso para pegar níquel a la batería? Jaja

[@muhamadsyariff8893]

Trafo yang di gunakan trafo apa itu pak ,berapa ampere? Dan elco berapa mikro farad

[@JaviersDIY]

Fir better understanding please use the universal language

[@muhamadsyariff8893]

@@JaviersDIY how many amperes is the transformer used? And what size is elco micro farad

[@JaviersDIY]

Maybe the transformer I used sir drops a current about 3.5A while the capacitor that I use is about 3300uf.

[@muhamadsyariff8893]

@@JaviersDIY ok thankyou ,the maximum voltage is 22 volts after passing through the elco and diodes

[@raffaelebarlotti9017]

Hi, great video! I would like to know the diode bridge from how many Amps should you use? Thanks.

[@JaviersDIY]

3A sir

[@ReelSpider]

@@JaviersDIY doesn't matter, because it doesn't work anyway... That's why he didn't show joining 2 strips.

[@sasangvaipheibilsapa7561]

Wat the hell 22v😁😄😄😄😄

[@ekasuryawan2318]

Kalau memakai power suplay bekas komputer apa bisa?

[@JaviersDIY]

For better understanding please use the universal language

[@orangpinggiran2487]

daya rekatnya GK kuat..ituh mah uji satu jalur aja wkkk

[@JaviersDIY]

For better understanding please use the universal language

[@wasiskendang5218]

lawak🤭

[@kelvyncharlie4876]

explaining is better than those background music 🙄

[@automationpk6720]

Totally failed because voltage is too hing

[@yuya249]

What is the voltage of the diode?

[@JaviersDIY]

1000V 30A sir.

[@jairoalonsofonseca6128]

The efficiency or the service that this circuit can provide or be useful is not appreciated

[@Tomas_Prucha]

I like it.Nice work!

[@JaviersDIY]

Thank you sir. Comeback again

[@boanergesrodriguezm]

En el momento de unir el positivo con el negativo se produce un corto y se funde el fusible de entrada alterna (110 Voltios AC).

[@JaviersDIY]

For better understanding please use yhe universal language

[@boanergesrodriguezm]

@@JaviersDIY At the moment of joining the positive with the negative, a short is produced and the fuse of the alternating input (110 Volts AC) blows. For a future reading comprehension: copy the message and paste it in any text translator you have.

[@untungsuharto7991]

Change capasitor with 500F, 2.7v or capasitor bank for mobil audio

[@N.g.Chanal]

not done weld.

[@ARSENIOCO]

KEN GOOD SINGER KA NAMAN HARANA MO C JILL NG I'LL NEVER THOUHT NI DAN HILL SIGURADONG MAKILIG YAN

[@olegi.4681]

Где реальные тесты по сварке 18650?

[@JaviersDIY]

For better understanding please use the universal language

[@olegi.4681]

@@JaviersDIY Can't you use translators? Weird...

[@JaviersDIY]

@@olegi.4681 no sir

[@olegi.4681]

@@JaviersDIY Okay, I'll ask again. Where are the real 18650 welding tests?

[@Gamer_53727]

​@@olegi.4681 This is not a welding machine.. Its a spark machine 😂

[@olegi.4681]

Where are the real 18650 welding tests?

[@nguyentaniep5524]

ok

[@ERNESTOGUEVARA1957]

Eres un espabilado de la electrónica ,primero hay que aprender los de los colores de los cables que para eso están y luego haces videos cómo dios manda ,,, es decir bien y respetando siempre la normativa

[@JaviersDIY]

For better understanding please use the universal language

[@ERNESTOGUEVARA1957]

Para montar un cuadro de luz tú madre de Dios

[@shrikrishnakulkarni655]

This is very basic circuit. Video doesn't show welding of two stripes. There has to be many capacitors to provide enough energy required for melting two surfaces of stripes for welding. Also there has to be either current limiting circuit to protect diodes and transformer from repeatedly shorting or atleast timer circuit to limit short circuit period. Don't build this circuit as shown.

[@hidayat7881]

Sebaiknya menggunakan bahasa Indonesia kalau di Indonesia biar mudah dimengerti

[@sasangvaipheibilsapa7561]

It should b 2 or 3 v and 200 amp atleast don try to fool us hahaha

[@alifqastalani2430]

i think its not function for spot welding nickelin

[@mariote1359]

Sorry but you have nothing, welding requires high current

[@SamsungGalaxy-nf4uf]

Musik nya menjengkelkan, nggak enak didengarkan, video nya nggak bisa dicerna aturan jangan pakai musik biar tenang

[@JaviersDIY]

For better understanding please use the universal language i

[@sg6630]

It s joke ? but not Spot Welding

[@danilogo235]

Im not satisfied. Sorry???

[@oturanboga6225]

[@MrRcvaldaris]

Not clear presentations

[@sergeypetrov1358]

Игрушка

[@JaviersDIY]

Fir better understanding please use the universal language

[@юрийфадеев-о3я]

Эти точки нафиг никому не нужны,показывать надо на деле,то есть приваривая никелевую пластину к 18650,а может вы не соображаете для чего сварка,тогда извиняюсь

[@JaviersDIY]

For better understanding please use the universal language

[@rdxrckurjagamer5745]

তুমি যে এইসব জিনিসপত্র লাগাচ্ছ সব কি নাম বলেছ না বলনি এখনো এক এক করে লাগাতে হয় আর জিনিসপত্রর নাম বলতে হয় না হলে বুঝবে কি করে

[@JaviersDIY]

For better understanding please use the universal language

[@Хренсним-т9м]

игрушка.нет пользы.

[@JaviersDIY]

for better understanding please use the universal language