High voltage HHO drive circuit

[@125varma]

I wish you would check the input power in both cases, here is why: When you close the secondary, the current runs through the secondary. That will reduce the impedance of the primary, thus primary will allow more current to pass through it. More current through the secondary that is in series with what cells, means more current passing through the water cell. When you close the secondary, the power consumed by the system goes higher, so the HHO output will also go higher. If you remove the MOT all together, you will get even a better results, because then a lot of current will be able to pass through the cells :D Just remove the MOT and let's see what happens to the HHO output and the LED light ;)

[@brettmoore3194]

hey , 42.1khz at least 20kv and 20ma to 1a in distilled water, you will actually fracture water instead of electrolize. higher milliamps will produce liters per second so be careful of any spark gap

[@muhammadamir2319]

what do you mean " fracturing water"

[@strvoder1557]

Brett Moore Can we get you schematic?

[@klay6483]

Fracturing water means to pull apart the molecules of Hydrogen and Oxygen through the attracting the opposing polarities

[@alvincrosby1492]

this is dangerous area , stick to Electrolysis

[@amazingtoolsvs]

Make a video to prove your theory

[@gotoluc]

Great work mate!... looking forward to the official release and collective development. Thanks for sharing Luc

[@matrixman3111]

You need a spark gap adjuster, and use the Microwave Diode on the secondary, and you will get more production. Nice mechanical example of the HHO generator.

[@stevegreen9357]

What would that look like exactly?

[@edgarw5919]

Thank you for the demo. I have done similar work but different. In a stainless steel 316 keg. install 2 electrodes in side the +v keg insulated inside. One upper large one in linear string form as being a grid to receive the electron surplus wen gas production starts. the lower electrode is a upright diamond mesh 316 in cylindrical form and is negative - V. Put 24 v dc in no pulse mode in, and gas will flow, place 24 volt light bulb on the upper grid wire and it will light up, and at the same time your gas production increases multi fold by the grid being also a gas producer. have fun.....

[@stanleymeyer9936]

Are you sure you can have the wires inside the water? I thought only the stainless steel can be inside the water💧

[@edgarw5919]

Also, if you take a multi meter with a long probe stick you can read the volume metric field where the predominant electric charge field is.It is above the negative field where the long string wire grid is placed. the rising bubbles carry the charge....

[@hoptoads]

Great work Tinman. Thanks for sharing. Looking forward to see more videos showing your progress.

[@gasolinevaporsystems9022]

Good Morning, Could a Standard Rheostat, (Dimmer Switch) be substituted for the Spark Plug? Thank you for your great work. Kind regards, Mike

[@gasolinevaporsystems9022]

Good Morning, I would like to replicate your system. Can you please tell me the Part number of the Transformer that you are using. Could you also please Identify the Capacitor specifications that you are using? Thank you, Mike

[@marcusgarvey8668]

Pull a microwave apart and you get all your part numbers lol 😂 #VoCoTech #NewGenerationXTv #AfroNation

[@mauriciopacheco12]

espectalcular felicitaciones Dios te bendiga gracias por compartir

[@mobigozer]

Tinman, Maybe a stupid idea, but some days back I read from a guy using a rodin coil between the capacitor and the sparkplug. He also put the sparkplug in a copper-tube, or some copper tubes, which even made the efficiency of the 'radiant energy' higher. Maybe something to try with your sparkplug? Best regards, and looking forward for new year, yeah! H

[@snugglylovemuffin]

Looks up Dale Pond and how he dissociates water with sound. If you want 1000 fold production of HHO you are going to want to jump that voltage up closer to 50kV and put in a PWM and play with the frequency a bit.

[@morningstarsci]

Have many amps are pulling from mains?

[@PackratCND]

Maybe you could show a wiring diagram of your setup to make it easier to understand......

[@11T872]

That would be great.

[@zahirnaseem542]

I love your experiments thanks for sharing

[@garystinten9339]

You said smartdrive washing machine and truck alternator? What model washing machine did you use and what model truck alternator?

[@garystinten9339]

Could you please show us a video to record all amps and current through each part of the circuit? Could you also on the video run your test on the dry cell and show us the production of the cell please? I would love to see how much this also in a car running too. Think a Junker or a test bed for the engine should be adequate, but a naked engine with fueltank and pump running plus integrating the hho system into the engine and demonstrating it operating would be cool.. Keep up the good work.

[@cr33po778]

+Gary Stinten Hehe... lol Gary! As persistent as always!

[@on_another_level5661]

I agree with :d ss: I'm not clear on the circuit. I know you're probably wondering how much simpler could you describe it. A diagram would be amazing!! thanks! Great work btw.

[@stealthop]

cool , nice amount of gas output on 1 phase .

[@TravisTellsTruths]

I'd like to understand. I've been obsessed with stan meyer. This is amazing. So you can create the gas with very little current? Amazing stuff

[@noway423]

Wow,Stanley Mayer style!!!💜🗝💜Thanks for share!!!

[@StefanDanov]

When you say "fresh water", do you mean tap water without or very little amount of electrolytes in it?

[@alexreyes4896]

Hello, can you make the drawing of the circuit for better understanding please?

[@bryanbenson6012]

Nice can't wait for your next video . Thank you so much for this one.

[@messengerofgod2788]

What will happen if you ignite a match?

[@stanzomanny]

Hi TinMan, where does the blue wire go, from the other cell?

[@stanzomanny]

never mind i see it

[@zeropointfuel]

Excellent work can't wait to see the next video!

[@tarotbug]

TinMan nice video nice idea with the MOT and spark gap demo with the oven cap, as a mater of interest whats the heat temp like ? All the best AG

[@edgarw5919]

It is a standing magnetic field! a compass above will respond to the field, also... 316 S/Steel is very high electrical resistance wire i used as electrodes.

[@thewonn]

happy new year!

[@jamessam951]

one thing i just noticed have you modified the mot i am thinking the primary n scndry in yr setup are the same thin high turn copper wire coils?

[@jamessam951]

i tried your setup but rather than alternator as u said i get the 22 or 24 volt from mot i have made n rectified but i dont get the arc with my setup could you give me an advice or help i really appreciate it

[@possiblenewenergy8101]

nice experiment, but think different: use strong oscillating electric field, that mean you have to use insulator and oscillate the voltage around offset value. the heroically value for resonance of water molecule bond O-H is around 10 Ghz that not possible by electronic, we can go max to Mhz, may with low frequency the O-H connection will oscillate at reduced resonance and slowly the distance between O and H increase until full dissociation. Job not done so far, we need to form h2 and O2, inside the cell put two plate short-circuited by a wire: each plate will be onside of plate for electric field. Because the water molecule is a dipole slightly charged they will aligned with the electric field, in one end we have H+ and other plate we O--, then they are charging slowly the plate emerged in water, the difference of potential will pull the electron from O-- and passed to 2H+ then you get H2 and O2. The dispositive then have two insulated plate for high voltage oscillating around offset and then you get the strong electric field. Two more plate are emerged in the water connected by wire to make equal potential in plate and then pull electron. The vibrating electric field will induce current flow through the other plate and you get O2 H2 plus electric flow. I’m trying to simulate the process, I’m facing big problem of time simulation can be one month running workstation

[@klay6483]

stan meyer only used kHz around 20 I think it was with high voltage.

[@jaywinstrand9680]

How much a/c voltage is supplied on the phase wire providing the primary coil? Does it matter? I only have about 8 vac volts coming out of my alternator phase wire, do I need to step it up to 120 vac or will it build inside of the capacitor on its own and eventually start working?

[@thewonn]

Hi, what type of scope do you recommend to find resonance? Thanks.

[@yosoyberm2136]

Hello Darrel, Is there a way to get the DC Voltage from the generator? also currents and frequency is possible, this experiment looks similar to Stanley Mayer dead secret. I'm guessing if you put the cell closer such Joe's cell, the HHO could be produced in massive way, Thanks for sharing

[@firepinto]

Awesome Tinman!

[@bakupcpu]

Very interesting :) Thanks for sharing!

[@waterfuel]

Meyer Cell fue un transformador elevador de 1.5KV a electrodos a baja corriente. Pulso de encendido y apagado Modo de ráfaga de CC 3 segundos encendido, 7 segundos apagado. Solo agua corriente o agua destilada. El VOLTAJE la presión - separa el agua. No electrólisis. Sin productos químicos. Múltiples celdas no son paralelas a una sola celda. Frecuencia del capacitor de agua (celda) = frecuencia de la potencia del pulsador. Obtenga los 2 manuales de concesionario de celdas de combustible de agua para obtener datos técnicos

[@yosoytrader]

You use a car alternator or o washing machine motor? And the transformer its from a microwave oven? Which is the function of the car spark plug? One of the thinks that i observe in Stan demonstration its he use 11tubes array and very long. I think its because the electrons can travel beter to the material by using high voltage. And also some maths secrets in the Number 11 (master number in numbers ciences).

[@mykedoes4099]

Tin man you using the spark plug as a transistor?

[@corneliuselbourne1044]

I think its a spark gap that oscillates at a frequency.

[@klay6483]

The spark plug is to induce a collapse of the magnetic field causing a spike in di-electric charge, which then produces the high voltage ... Look up Electric Discharges, Waves and Impulses by Charles Proteus Steinmetz

[@marsseeker6208]

I got more from a beer cap and a phone charger .I do have a question .how to fill the tanks after the production . I wanna use it for cooking

[@muhammadamir2319]

Can hydrogen be used for cooking ????.It will definitely melt your steel

[@suzesiviter6083]

There really shouldn't be any need to use high voltages; the key here is finding the resonant frequency of the H-O bond, which according to my calculation is around 104Ghz; though you could use lower as long as its a multiple.

[@muhammadamir2319]

Resonant frequency of H-O bond , very good idea to work on. Thanks

[@suzesiviter6083]

Muhammad Amir: The resonant frequency will have to be be tuned very accurately for separation to occur; that's based on experience in resonance in other systems. Also remember water is diamagnetic, so it may be possible to resonate water using a powerful fluctuating magnetic field.

[@muhammadamir2319]

Suzy Siviter .Thanks but thought the system itself matches the resonance frequency with that of water and leads to it's breakdown. What I mean when the two frequencies are falling near by than they match and lead to breaking if water. Why I am thinking this because in this video no apparatus is used to match the two resonant frequencies

[@suzesiviter6083]

Muhammad Amir: The generator he is using outputs a frequency so low as to be way below the natural resonance of water. You could use the analogy of a glass breaking once the singer matches the natural resonant frequency of the glass. Water is more complex as you have multiple resonances, you have those associated with the H-O-H and those with the H-O, but if we manage to shake the H-O band violently it will break the bond. You can break the H-O bands through simple DC voltage electrolysis, but its not very efficient as it uses lots of energy, AC electrolysis at high frequency should be more efficient and will become close to 100% efficient if the resonant H-O bond is excited precisely just like the wine glass. Look up Sono-luminescence, you might be very interested, I was.

[@muhammadamir2319]

Suzy Siviter thanks a lot. Great idea

[@damith9220]

I wish i understood what that part about the washing machine motor for. I think he needs an AC single phase power supply, so can i just plug the primary of the MOT to the wall socket? (Single phase 220V) Its very hard for us normal folks with minimal understanding of electronics to comprehend this science. So far this is the only video i somewhat understand.

[@Darrellsrelm]

Nice work! with the set up can the two leads going to the lightbulb be hooked up to two more tubes to produce more hydrogen? If so you may be able to capture more lost energy in the waters Eddy current?

[@gilsonsoares-mz2lc]

Had the good being made the electrical diagram of this project available for us to do at home?

[@crafter2u]

so you are pumping in AC to the cell?

[@69Atho]

No,the voltage and current remain DC due to how the HV coil is shorted with the spark.This induces a very strong magnetic pulse into the primary coil that is hooked in series with the cells and alternator.

[@Darrellsrelm]

Way cool TM! Can't wait to see the next Vid. Thanks for sharing "D"

[@h2opower]

Just as a suggestion try making a Tesla rotary spark gap so that you can control the sparking perhaps a bit better.

[@m3sca1]

Interesting setup. You can slow the burn rate of HHO by running the gas over a plasma. Plasma source I used to prove this was from an ozone generating device. It seems odd to me that the HV side of the MOT is electrically connected to the iron core. Thats how they are built and I figure it would reduce efficiency by heating the iron up...your thoughts?

[@69Atho]

The iron will get no hotter that usual,as it is the copper coil that produces the heat,regardless of where the terminations of the coil are. All HV output's over here in Australia must have one end go to ground unless they are what is called!double insulated!,which this one is not.

[@junglerider007]

Theirs a mistake here in the video.Im sorry if im wrong.But A simpler design from my perspective would be as follows: A microwave transformer is a step up transformer not a step down,,so ideally the alternator to be used to source ac power from should be able to produce at least 230 v ac or 110 v ac depending on the country the microwave transformer was desighned for.If it can manage even more AC voltage,at the input if its rewound uniquely,,that would help even more,,for the primary .Now the secondary of the microwave transformer is already boosting to very hi voltages in Ac current due to its desighn,,Now All you do is convert it to dc through a diode of high voltage and ampere capacity and then hook it to your hho cylinder device etc. personally i coulnt understand how the spark plug used as a spark gap works here.. But more than anything else...this is highly dangerous desighn,,not suitable for automobile applications and a simple mistake or innadequate insulation you get electrocuted and die. (i wonder instead of all this ,,has anyone tried it with a HID ballast ,,you get it for auto mobiles as well as for domestic factories,,all one needs to do is add a diode or two to convert it to dc...then again 1amp is enough to kill you @60vdc so better not to play with high voltage ,,where the human bodys skin resistance starts to dwindle.

[@klay6483]

sounds like you have a really good understanding of electricity, but the thing that your missing is the reason for the spark plug in the first place. This is to be able to eliminate the magnetic field which then causes a massive spike in voltage which is then fed back into the primary coil. The timing of the spark, is controlled by the gap allowing for tuning of the system in order to attain the correct oscillation for the system to work efficiently. When Stan Meyer did it, he used a set up with a transformer, a primary coil and a secondary coil. The secondary coil would then be used to be able to tune the system to able to resonate the electrical charge between the stainless steel tubes and the coil which would in essence both become capacitors.

[@marcusgarvey8668]

What's up Tinman #VoCoTech #NewGenerationXTv #AfroNation

[@donotwantahandle1111]

I'm having trouble understanding the circuit - the secondary is usually the hv windings on a transformer but you say a short in the secondary induces a hv in the primary? I don't get it. The spark plug isn't a short circuit but when the spark jumps you get a huge increase in gas! Shouldn't the secondary circuit operate the electrolyser? And why 3 tubes on the left electrolyser?

[@69Atho]

Each time a spark jumps across the plug,the secondary induces an extremely fast magnetic field change in the primary of the transformer. This causes a very high voltage to be produced by the primary. The primary is being used,as it can deliver a higher current to the cell, than that of the secondary

[@klay6483]

it's because of the di-electric surge which happens look up Electric Discharge, Waves and Impulses by Charles P Steinmetz

[@MrMraza123]

What is the role of electric motor in this protect.

[@11T872]

generator hv

[@babesonly-bevisuallydefine7666]

Just remember that Stanley Meyers 8XA (Tesla Choke) Coil restricts Amperage, prevents the 'Skin Effect' taking place & only allows 'Pure Charge' without the Magnetic stream to pass, in Darwin NT Australia these are referred to as 'Infinite Q Resonators' as they recycle Charge in an Loop. The Meyers 'Electron Extraction Circuit' provides a dead Short Circuit which is the path of least resistance for the Amperage to flow into as the Amperage is restricted by Meyers 8XA Coil... This is very Simple!

[@klay6483]

you really don't want amperage in this system, you want to aim for 0 amps and extremely high voltage. Which is what is happening with the spark plug as it's causing a di-electric charge of high voltage every time that the the spark is released which eliminates the magnetic field.

[@arthurcooper1007]

i made two big ones and i run my car off of it i have been for about 4 weeks now works great .....

[@scottneels2628]

I realise this is old but just wondering if you can suggest a forum with the the least bs for me to learn from please. You strike me as a character who wouldn't put up with bs.

[@alvincrosby1492]

interesting ,use all 3 phases, short one diode or use a leaky one, may replace with resistor, target resonant freq with speed controller and use a scope, cal cap of cell and inductance , pull a vacuum from motor near inlet manifold , target is 3% in air , water quality is very important the higher the purity the more dielectric it becomes , tap water contains inhibitors from its processing.donot try and compress this gas ,its not wat you think it is .

[@shazizz]

Very nice.

[@darkarmy3237]

can hho generator blast ??

[@parakhgavel981]

Thanks

[@babesonly-bevisuallydefine7666]

Nice setup but, its a bit silly having the microwave capacitor. The Water Fuel Cell is the Capacitor in series to the Coil & Tesla Choke (upon switch closure the Choke uses its own magnetic field to create a massive B-EMF Im-Pulse) that restricts current flow & provides the Im-Pulse Charge in Stanley Meyers original patent. Also the reason there is no 'Short Circuit' in a Stanley Meyer setup is because a dead short circuit prevents Voltage from cascading. This is just a suggestion but, you could incorporate a NPN Transistor with a Light Bulb in series so that when the + is off the Light Bulb shines but in a pulsed on, off manner to ensure that the Voltages are continually cascaded.

[@mikekerezsi9672]

How many volts/ amperage

[@mobigozer]

Great Tinman! Like your work very much, where can I buy shares LOL :-) Best regards Hans

[@jaimefloresalvarez1752]

algun link para comprar planos o diseños

[@Darrellsrelm]

Any update with this project yet???

[@69Atho]

Hi Darrell,it's been a while lol. But yes,i am finally getting back to it. New generator,motor,and your cell is all being put together now-so keep an eye out.

[@Darrellsrelm]

+TinManPower can't wait to see it. What forums are you on so we can communicate more often. I have some things to share with you and to catch up on. Thanks "D"

[@ThePaulbilek]

I have the same 130 electronic lab experiment kit lol

[@Desert-edDave]

"Doesn't want chemicals in water." -Uses tap water.

[@Machiuka]

Hi Tin Man ! I've saw that you abandon that setup, despite the fact that it look very promising. Why's that?

[@rickgebhardt3382]

So let me get this right, you put this video up. Then you don't show a schematic. Then you don't even show that it works. Just one question. Is there any reason for you to think it works?

[@neilemos1]

Boa Noite, seria possível o Sr. me enviar os dados para que eu possa replicar esta experiência aqui no Brasil, sou um apaixonado por HHO...Por favor...

[@gilsonsoares-mz2lc]

Motor de combustão interna, caseiro, movido a água. @

[@Thelordoftimeiscoming]

Palavra staly mayerde elektronik devre var bu yüksek voltaj trafosu 1000volt çıkarıyor ve hidrjen elektoliz olayında çok ısınıyor çık çık çalişmazsno rabote

[@xoobis]

sweet

[@NineElevenisAnInsideJOB]

Where is the followup video ??????????????????????????????

[@godofdestructiondhanasekha893]

circuit diagram please

[@hhogasproduction5081]

What are mouduel

[@crafter2u]

yep i want to try this

[@hhogasproduction5081]

I'm interested in a mouduel can you please sport

[@rainmanferguson]

This guy has made so much money trading hes selling you something else lol.....

[@rainmanferguson]

opps that was to the add lol my bad

[@shanmugasundarj3245]

Bike use same direct ac volt

[@abdumalikhakimov6123]

this is not effect HHO this is toys

[@roserecruitments6762]

NOT CLEAR. mr tin man. Please show in diagram it will be better to understand.

[@vasiltin3314]

Nobody shows what electrometer sayes

[@woodzyfox4735]

28v isn't high voltage... Try like 500v+

[@egbertoegondeherdani6645]

Todo esse gasto de energia e barulho para produzir muito pouco. Ineficiente.

[@gilsonsoares-mz2lc]

High Voltage Radiant Charger - Small Battery Charging a Big Battery kzbin.info/www/bejne/gJ3NpGCVetaEmKc

[@gilsonsoares-mz2lc]

Gerador de hidrogênio muito LOOUKO 110v kzbin.info/www/bejne/l6uoiGyvgt6So68

[@gilsonsoares-mz2lc]

A maneira mais barata de se produzir hidrogênio , vapor de água ou água quente. kzbin.info/www/bejne/n6OTlWdjqqZmi6M