hilti avr1000 red ligt fix, hilti avr1000 Service light repair,Cut cord repair,
Пікірлер: 41
@williambinn10283 жыл бұрын
This works with the TE-1500AVR model, except that I used my TV remote control to reset the service light. The TE-1500AVR is almost exactly the same as the 1000AVR. My procedure was to Plug in the mains power, turn the operate button to ON (this makes the red service light come on), then turn button to off, then disconnect the mains power, and while it is off, flash the remote control into the service light lense (no need to disassemble the hilti covers) and just push the buttons on your remote randomly. Every time the hilti picks up the Infrared beam from the remote the service light LED will flash. The reason is that the capacitors in the AVR are still charged so the electronics will work for about 15 seconds after the mains power is disconnected. After about 4 or 5 flashes plug the mains power back in and the Hilti should start operating again. If the service light is still on while it is running, flash it with the remote once more and the service light should go off. I must admit though that I have had to mess with this procedure a few times, and it seems to work randomly with a combination of Mains Power (on/off), Operate button (on/off), flashing at the same time as connecting the power...... its just trial and error. I have also used a tiny keychain laser and while I could get the light to go off, I could not get the hilti to operate. I also used the laser on my temp tester and got the same result. The remote control worked best for me.
@laponsacca38713 жыл бұрын
Thank you for the explanation. Could you tell me what model of remote control did you use? for which TV model?
@williambinn10283 жыл бұрын
@@laponsacca3871 my remote is actual a Digicel tv remote (decoder for recieving 40 tv channels, not an actual tv), It has no branding from the manufacturer. But try all the remotes you have. Use a different button each time. Try different combinations of turning the mains power on/off when you do. With one tool I turn off the mains and do it and the service light flashes because the capacitors inside the drill are still charged and powering the circuit board. One drill I had to turn on mains power then pull the trigger to get turn on the service light, the flash it with remote, then pull the trigger and it works. One jackhammer needs to be flashed everytime we want to operate it after the mains is turned off/unplugged.
@gtsalbania75243 жыл бұрын
@Nico kzbin.info/www/bejne/nmGniIyYbq6qhdU
@gtsalbania75243 жыл бұрын
@Nico if you need the device just contact me
@muhammadfarook Жыл бұрын
www.youtube.com/@HILTI.Pakistan Hilti SRT reset tool red light off available here connect
@elrincondelmecanico3 жыл бұрын
The TE 1000 have a working time of 200 hours, at 180 the revision light turns on and you have a limit of 20 hours to work until it is blocked, what is done in this video is to turn off the light to prevent it from lock, a locked hammer does not work with the red light on
@MarianKowal30005 жыл бұрын
Excellent job man . Only one question . Can be it done without disassembling breaker ? Just hit the red light when it's sitting in the plastic case ?
@FlooringRemoval5 жыл бұрын
Marian Kowal i was able to rest with cover on. Needs to be a Strong red light.
@MarianKowal30005 жыл бұрын
@@FlooringRemoval I have ET 3008 AVR . I will check it right now
@MarianKowal30005 жыл бұрын
Sorry I have ET 3000 AVR I try it , a red light go off for a while but motor not powering on .
@FlooringRemoval5 жыл бұрын
Marian Kowal try this if light is off. Turn off, unplug from wall, turn on,then off. Plug in, turn on, turn off, then on.
@powertoolsrepair Жыл бұрын
@@MarianKowal3000try to check whats wrong with tool
@eljorrox55528 ай бұрын
Lo ise con t1000 avr con rl control y lo apague trabajando pero despues de un rato volvio la luz roja lo intente otra ves y lo apague funsionndo otra ves espero que no se vuelva a blokear
@stoneyvill3 жыл бұрын
From what I have read they are set to shut down after 200 or 250 hours. Could you imagine if car manufacturers turned your car off at 12k and only they had the means to start you back up.
@skylerjoemarekchan83134 жыл бұрын
Good day sir.. is this applicable also for TE 40 avr?
@marcelinomarcelino86843 жыл бұрын
Hi . Is there no way to override the hour meter so that the red light does not come on?
@elmiguel18693 жыл бұрын
Yes.. you would need some prom connector's and some 16 gauge wire
@marcelinomarcelino86843 жыл бұрын
@@elmiguel1869 do you speak Spanish? Can please give me some help? marcelomastroianini@gmail.com
@borhenzarrami26613 жыл бұрын
@@elmiguel1869 hi, i managed to turn off the red light with a laser beam , but now it won’t start. Any suggestions please
@croatiaboy972 жыл бұрын
@@elmiguel1869 Hello Miguel, what contact do you put together that it works again ?
@dicloudy12594 жыл бұрын
Why does the red light come in ?
@Mohanad-x6c4 ай бұрын
It's not true if the light still blinking that's mean there is serious problem in the motor
@dareksieron614 жыл бұрын
How to reset red light on TE 905 ?thx
@servistools56913 жыл бұрын
😁
@alejandrolazonunez75834 жыл бұрын
hello anyone who know if its woks with a TE 3000?????
@matthewpalmer51505 жыл бұрын
Can anyone verify if this works for the TE70? Just a laser will reset it? That's it?
@FlooringRemoval5 жыл бұрын
Did you cut the cord?
@FlooringRemoval2 жыл бұрын
Professional flooring removal services Tampa / Oldsmar (813) 732-6828 g.co/kgs/jVsqzk
@syte75444 жыл бұрын
i have same problem and i also tried solving it with a laser and it worked but as soon as you unplug it and turn it back on again the light comes back on again ................. Any one found a salutation.
@elmiguel18693 жыл бұрын
If you still have one bypass it.
@mohammedyaseen-cw4gv2 жыл бұрын
How to bypass?
@muhammadfarook Жыл бұрын
Hilti unlock device SRT reset tool available here connect on email ✉️