[Hindi/Urdu] Hydrotest - Basic Concept of Hydrotest & Test Pressure Calculations Explained

[@dnyaneshwarmaghe8571]

Thanks for such useful information. Nice job Sir. I want a video on topic of SOP-standard operating procedures

[@yusufk311]

Hello sir kyse hai aap aapka bahut bahut sukri aapka vidio dekh ke bahut kuch sikhne ko milta hai mai aapka cswip 3.1 ka 7 chap taq pura vidil dekha hu aapse requst hai ki aap pura chap clear kare plz..

[@WeldingandNDT]

Thank you. Please visit my website www.weldingandndt.com/

[@rajanchaidhary3016]

Sir pls tell me about of DPR .

[@ManojSharma-zj8jr]

Described excellently...🙂

[@WeldingandNDT]

Thank you. Please join my channel to support my initiative. Joining link: kzbin.info/door/H7nXSievFlbRKzKzEySbkwjoin

[@mustafahasmi998]

sr aap na yah st or sd ka liya yah valu kha se liya eska koi ek standerd code aata hai kya like according to pipe or gr pls sr answer this question

[@AsifKhan-o6d3o]

Complete test n rig up btaye chart recording sy pump tak ki detail plz

[@Road_rebel179]

Sir please make a video series on pressure vassal, heat exchangers and tanks , it will be very helpful

[@WeldingandNDT]

Sure. I will try my best

[@mdsadafuddin6227]

What pressure will be use for hydrotest????

[@alfaizahmed9387]

Please make a video for how to prepare for hydrotest test pack?

[@shamratmiah1137]

Sir please carpentry welding pe video banaiye.

[@tripureshkumar7321]

Sir please post a video for dead Wight tester working process and liquid calculation in a pipeline during hydrotest...

[@amitkaushik78]

sir is there a chemical also used to do hydrotest in an air reservoir

[@shaileshkumarsingh4689]

What is is code for hydro test of DI pipe

[@anirudhchoudhary3035]

Sir, please make videos of pipe line hydro test and also explain all instruments used in hydro test and function of all instruments and why use it

[@ramkishor2220]

I love you sir💝🙏

[@WeldingandNDT]

Thank you. Please join my channel to support me. Joining Link: kzbin.info/door/H7nXSievFlbRKzKzEySbkwjoin

[@sumitraj1674]

Sir please pipeline ke HDD Section ke pre hydro test per video

[@SandeshKumar-ol8yc]

Sir water ki quality kya hogi

[@AbdulMannan-tq3eg]

Very good sir

[@WeldingandNDT]

Thank you. Please join my channel to support my initiative. Joining Link: kzbin.info/door/H7nXSievFlbRKzKzEySbkwjoin

[@viv6686]

Sir ,air water volume calculation ka video banayiye please

[@krunalkapadia2299]

You will get stress values from Table 1A in ASME SECTION II PART D for 1 numerical and for second SS316 you can check ASME SA-240 316 GR for value of design stress

[@AD_43]

Sir, please make video of air volume calculation during filling water in the pipeline

[@faizanrazs107]

Sir hamlog 2 guage kyon use karte hain hydrotest k liye

[@aamirakhtar1789]

sir lifting /shifting rigging plan bataye kaise banYe gye especially espe ek vdo banaye

[@mohammedamjad3978]

Excellent.Why not Hydrotest pressure of Pressure vessel=1.5XDPX(sttess at Test temp/stress at Design temp). Kindly clarify.

[@sadiksaiyed1774]

HYDROTEST Loop pack kya hota hai sir QC me aur kya kya check Kiya jata hai hydrotest loop pack me

[@anubhavshukla3988]

Sir Please tell the actual reason for doing pre hydrotesting of an HDD section

[@rakeshkothari3249]

1) What about sensitivity of pressure gauge. 2) Does there exist any reference in ASME code for inservice hydrotest pressure.. 3) Factory rule irrespective of ASME construction code says 1.25 times as inservice hydrotest pressure..

[@pavaningle]

Which std states holding time as 6min / cm..?

[@mdibbu123]

Sir, if possible make a practical video

[@shubhamvaishnav6178]

Sir me Ko agar shikna h hydro test to kha Sikh sakta hu...koi institute sikhati h kya.....

[@bhautikpandya2883]

very useful video.

[@WeldingandNDT]

Thank you. Please visit my website www.weldingandndt.com/

[@lokeshmanjhi]

Sir, please explain Overlay welding..

[@mplate3021]

Thanks sir

[@WeldingandNDT]

Thank you. Please join my channel to support my initiative. Joining link: kzbin.info/door/H7nXSievFlbRKzKzEySbkwjoin

[@dawoodkhan1713]

SIR PLEASE COMPLETE THIS CSWIP COURSE AS SOON AS POSSIBLE. I AM LEARNING FROM YOUR VIDEOS AND I ALSO HAVE JOB OPPORTUNITY THIS NOVEMBER 2020. SO ITS A KIND REQUEST TO UPLOAD ALL THE CSWIP VIDEOS IN SHORT GAP. PLEASE 🙏 ITS A REQUEST. IT WOULD BE HELPFUL FOR ME.

[@kprajesh7893]

sir please explain shutdown job interview questions for welding QC inspector. what is main requirements for shutdown projects ?

[@rajasahib5683]

Sir stick welding k liye volt aur amp kitne hone chahiye.

[@WeldingandNDT]

Volts amps Ka video available hai

[@vishalraghatate9671]

Sir what is the effect of temperature drop during hydro test.

[@PrabhatKumarSingh-m2c]

Good, morning

[@avinash7003]

Sir make video on Erection methodology

[@ashutoshgupta8415]

Sir, you have mentioned here 2 hr as maximum limit of hydro test but generally in pipeline we do hydro test for 24 hrs.

[@dnyaneshwarmaghe8571]

2 hours Minimum time

[@ashutoshgupta8415]

@@dnyaneshwarmaghe8571 but in video range is mentioned as 10 min to 2 hrs

[@dnyaneshwarmaghe8571]

@@ashutoshgupta8415 I don't why they mentioned that range. I am working in Pressure vessels fabrication and we generally conduct hydrotest for 8 hours for Pressure vessels and minimum 2 hours for storage tank or piping.

[@ashutoshgupta8415]

@@dnyaneshwarmaghe8571 exactly

[@AMIRSHAHBAZ-vp3wd]

Same 24 hours

[@shubhamjadhav8530]

I think the holding time must be 6min/mm of thickness instead of cm

[@AD_43]

According to ASME B31. 3

[@harishtiwari8275]

हाइड्रोलिक टेस्टिंग करने के लिए सरकार द्वारा कौन सा कागज बनवाना अनिवार्य होता है मैं फायर फाइटिंग का काम करता हूं

[@mandeepsingh3198]

Sir plz apna number send kare