Abbreviations LS = Minimum setpoint US = Maximum setpoint
@Jordan-gt8ht Жыл бұрын
Is the minimum for the highest hot point and the maximum for the lowest cold point?
@TheAmazeer5 ай бұрын
Not logical @@Jordan-gt8ht
@argenismoreno72533 жыл бұрын
Good video. I have a Emerson Digital Controller , It shows me on the screen p2, the problem is that the evaporator is leaking of ice, it does not do the defrost cycle. You can help. Electric Heater is good 👍
@brittanyrodriguez91776 жыл бұрын
This doesn't tell me how to make it the temperature I want and the instruction manual doesn't either.
@daweicunningham6819 Жыл бұрын
The one your looking for is LS and US possibly just use SET if yours is already mostly set up. Unlike mine many others used before I got to it so all the values are changed and I can't find any source or info about the default values. I know how to change just don't know the rec settings/ factory settings.
@westonroberts917411 ай бұрын
@@daweicunningham6819the defaults are stored on internal memory and you can reset back to them. It’s in the manual somewhere how to do it.
@ThePizzaJointFl-fw8cu11 ай бұрын
How is it possible a $5000 piece of equipment has such a lousy instruction manual? It doesn't tell you what any of the abbreviations stand for.
@depecheddurand6 жыл бұрын
why don`t they make it easy like traditional thermostat? why the fuk make it so complicated ?
@mihmihmihmih85356 ай бұрын
Thanks bro
@OnionChang5 жыл бұрын
Where is the parameter list?
@juletazizi46177 жыл бұрын
Hk International I do exactly like you but the temperature still 35 ° do you know what can I do more ?
@vikkit8775 жыл бұрын
Hi. I follow the steps but it’s still not the temperature that I want. Help please. Thanks
@glennharrington70507 жыл бұрын
How do you put unit in manual defrost, to check this circuit?
@Tukang_AC10 ай бұрын
thanks for a good video
@wyattsavage31384 жыл бұрын
Just tell us how to raise the temperature so all of my drinks dont fucking freeze
@maxmass77463 жыл бұрын
Well done keep it up for message
@vothieu51812 жыл бұрын
Character In the video It's great, I like it a lot $$
@selvarajanv.achary76284 жыл бұрын
Our temperature -20 degree.show multifreezer combine unit and full wiring and settings and symbols.
@sudeshputran69 Жыл бұрын
Super
@AAZer08 жыл бұрын
Thank you, that is very helpful.
@villagemedia85946 жыл бұрын
WHY COMING P2 please answer me
@leticiazamudio28015 жыл бұрын
Anyway to set it from locking? Door locks for a few seconds after we open the door each time.
@nuclearusa161205 жыл бұрын
The "locking" effect comes from the door making an airtight seal around the perimeter of the door. When you open the door, you let in a blast of warm air, and let out a blast of cold air. When you close the door, the warm air begins to cool. Cold air has a lower pressure than warm air, creating a suction effect that makes it very difficult to open until the pressure equalizes. That your freezer does this is a sign that your gasket is in good condition, and is working properly.
@mayimrai17904 ай бұрын
It goes back to 25 degress once i set why?
@เกษตรชาวบ้าน-ด5ภ2 жыл бұрын
ซื้อได้ที่ไหนครับ
@mahesh1757sardesai5 жыл бұрын
what is EA error in dixell XR06CX controller, PLEASE reply at the earliest
@wafi23654 жыл бұрын
hi mahesh have u found a fix for that issue? i have problem EA blinking too
@iyusrandy28253 жыл бұрын
Q o w
@Faizankhan786943 жыл бұрын
plz uplode blast freezer progaramig
@Herbertl_Lee3 жыл бұрын
Hi I am able to enter the program mode before but now when I hold the set and arrow down button for 5 sec it displays pof. What I am doing wrong?
@terrygumlich7272 Жыл бұрын
How do I set the defrost on this unit
@sankethsanku26266 жыл бұрын
What is P2
@karuppaiyanatarajan59144 жыл бұрын
இந்த டெம்பரேச்சர் ரீடிங் சரி செய்வதற்கு தமிழில் பதிவு போடவும்
@LTDANMAN44 Жыл бұрын
is there a factory reset parameter????
@ajmalhussain48086 жыл бұрын
I want yonjlw to reset or setting for table top cold show case for cake n pastry van u help me out of this its geeting more cold
@anvarshandileep75005 жыл бұрын
Defrosting time?
@veritasaequitas98754 жыл бұрын
For a company as big as HK International this video is an embarrassment. It tells you absolutely nothing. It was published over 4 years ago and not a single response from the publishers to any of the significant questions raised by the audience who have clearly come here looking for answers that they didn't find. Word to HK. If you are going to engage in social media then at least make an effort to give the job to someone who is competent enough to do so. Whoever produced this crap is clueless not only about engaging with the general public through social media but also at the product level. Once the unit is installed it should be obvious to anyone who has been through that process what the next step is likely to be: set the preferred working temperature. That's what this video should present in a stepwise fashion. Not some general discussion about how to change the many and varied parameters most of which are vague at best as to what they represent. Must do better.
@antondejesus23073 жыл бұрын
This answer represents the feelings of many people going through the same frustration. There's zero information here on how to actually set anything up.
@normanbergenstein34545 жыл бұрын
How do I shut off low Temperture alarm .? MBF8501
@grande-14-jojo6 ай бұрын
What is HE error
@IftikharAli-ld7hd Жыл бұрын
Pi coming what problem??!
@jesusvargas20964 жыл бұрын
hola buenas tardes saludos para todos los colegas espero se encuentren bien les quería pedir el favor de ayudarme con tutorial en español del manejo de los parámetros de dixell xr60cx
@mahesh1757sardesai5 жыл бұрын
What is EA ( letters flashing )error in dixell XR06CX controller, can anyone help n explain it to me at the earliest please. Thanks.
@notanewbie17184 жыл бұрын
Is there audio on this video?
@jinoyjohn18 жыл бұрын
heloo how to adjust difference in on and off comprssor...
@albertomonrroy49077 жыл бұрын
What do i have to do to go back as factory
@dereksingh5437 жыл бұрын
what does the abbreviations stand for
@HKInternational7 жыл бұрын
What abbreviation do you have in mind?
@notanewbie17184 жыл бұрын
Just love silent movies. Verbal explanations would be they thing , don't you think?
@pcharles97504 жыл бұрын
What is the meaning _d_
@vijay97686 жыл бұрын
What is HT
@dionnewilliams68822 жыл бұрын
Saya tidak percaya ia boleh menjadi sebaik ini
@jasonshellyy41634 жыл бұрын
What does P2 error mean
@andykistner22404 жыл бұрын
My prep cooler was messed up! I decided to put everything back to factory default settings. When I did, P2 error started. So, in programming mode I changed my P2 parameter setting back to N instead of Y and the error stopped. My cooler’s manual is worthless. I had better luck looking at this manual for the controller: masterfrigo.com/wp-content/uploads/2013/10/XR06CX_GB.pdf
@gruetoo14 жыл бұрын
@@andykistner2240 Thanks for the info. Was able to change Dwell From factory setting of 7 to 5.
@jennychen56497 жыл бұрын
What does PF code meaning, when I am trying to hold Set botton.
@HKInternational7 жыл бұрын
Please call our Warranty Department for technical support at 1-800-877-7782 (opt 6) or email warrantydept@hki.com Thank you