Good day in this vedio I demonstrate how to Diagnose and Disassemble & Assemble Makita Demolition Hammer model HM1317C watch for your information thanks God Bless
Пікірлер: 22
@nelsonbida9958 Жыл бұрын
Is this model need oil change for several time of operation? Tx for the video
@powertoolsclinic Жыл бұрын
Yes. And also need to change o rings
@nelsonbida9958 Жыл бұрын
@@powertoolsclinic thankyoi for kind respond, but it has no oil indicator or oil inlet or outlet. Also no oil change procedure written in manual book, i try to find vidio about it, but still didnot found one yet
@user-ev1yk8qs9f3 ай бұрын
En donde puedo conseguir piezas del rotomartillo?
@powertoolsclinic3 ай бұрын
Hi user-ev1yk8qs9f please contact your local Makita distributor or dealer in your country With thanks
@user-kk4kw6hu1t2 жыл бұрын
助かりました
@powertoolsclinic2 жыл бұрын
Please translate to English.
@powertoolsclinic4 ай бұрын
@uaser-kk4kw6hu1t thanks,
@dedanikolaj2229 Жыл бұрын
Welches Reparatur Satz Schlagsystem gibt es dafür
@powertoolsclinic Жыл бұрын
Yes. Hammer service kit you can check in you local makita dealer in you country
@paulliberacki33969 ай бұрын
Nice work ! So i watched the entire video. I don't what i missed. What actually kept the tool from operating? I have 3 of these down at my shop and Im sure I checked everything. Ive checked and replaced switches, new brushes, new electic motor, ive changed a control board and still nothing. I have the green light but the tool will not operate. Any insight would be appreciated.
@powertoolsclinic9 ай бұрын
Try to replace o rings & x ring check to your local makita distributor or dealer in your country
@paulliberacki33969 ай бұрын
@powertoolsclinic Thankyou !
@MrBocsa4 ай бұрын
Welcome! How to measure stationary and rotating parts? I'm sure the engine is faulty, but I don't know which part!
@powertoolsclinic4 ай бұрын
What problems with your machine?
@MrBocsa4 ай бұрын
@@powertoolsclinic This is a Makita HM1307C Demolition Hammer! The problem is that it won't start! The green LED on the controller lights up, but the engine does not start! I replaced the controller, but the controller is not the fault!! I connected 12V to the brushes and the engine started! I measured the stator with an ohmmeter, without a brush holder! There is resistance between only 2 outputs, nothing can be measured between the others! Maybe one of the coils is broken?
@powertoolsclinic4 ай бұрын
Check the carbon brush if the carbon brush is short Replace it with the new one for the good of your machine Replace all O rings and Hammer grease inside the machine but if you don't know how to Disassemble contact your local Makita distributor or dealer in your country thanks
@MrBocsa4 ай бұрын
@@powertoolsclinic I solved the problem! There are two coils in the stator, one is broken! Thank you for your reply!
@powertoolsclinic4 ай бұрын
Carbon Brush is short or worn-out
@michaelhaze450710 ай бұрын
Makita or Dewalt? which is most powerful?
@powertoolsclinic10 ай бұрын
For me makita not only powerful but availability of genuine spare parts
@theungoliant94102 ай бұрын
your annoying red bell over and over again earned you a dislike. congrats.