Piece by piece, KZbin helps me with my Layout!! This is just bloody brilliant! I love the hinge idea. It keeps good alignment of the track. The only thing I might do differently is put some cork, or even wood strips, under the rails at the cuts. Not that there's a huge chance of that rail sagging.... but I have grandkids. One will eventually lean on, or push on, those rails that are suspended at the joints. Man, that's some clever thinking!! Just subbed. Carmine 🚂
@banjol459511 жыл бұрын
Looks Good to me, I'm glad you did this, I can see I'm going to have to do this when I get started. Please keep us up-dated. Phone camera works great. Thanks for sharing, Steve
@dacuzzz11 жыл бұрын
great idea for your lift up.. layout is getting there...thanks for sharing vinny
@bbrockRailFan5 жыл бұрын
Good thing about painting the wood is it helps a little with warping by sealing the wood.
@PennCentral9911 жыл бұрын
lift up section looks good and runs fine. the wheels on your locos and rolling stock won't notice much. if you haven't done so, slightly ile the inside of the rail to help "smooth" out the wheels passing over it
@efitter711 жыл бұрын
Nice work! You might want to add a section of facia to that area that sticks up above the foam by about half an inch. This would be to act as a guard rail to prevent any expensive toys from taking a fall. Just an Idea to keep things on the layout rather than on the floor. Thanks for sharing, I subscribed. Ethan
@andyevans93697 жыл бұрын
efitter7
@blakrootz5 жыл бұрын
I enjoyed this and I will need to incorporate it into my layout. Thanks for sharing....
@BNSF938211 жыл бұрын
Thanks for the tip. The "bump" comes from trying to line up the tracks, not from them hitting each other, if that is what you were saying... If all my benchwork was perfectly flat and level, it would be much easier...
@lionellance9 жыл бұрын
Great job. .looks good. .thanks for sharing. .keep up the great work. .
@joestrainworldvideos39774 жыл бұрын
Great help with these ideas. Thanks a lot. Joe
@jsrogers64645 жыл бұрын
Could you isolate a section of track on each side of the lift and then use joiners to make contact on each end? The raising end would use side contacts and the lowering section would use bottom contacts. Then when raised, the isolated sections would lose power, keeping any trains from crashing off or into the lift. Hope that makes sense. Very good job and nice video.
@drumday11 жыл бұрын
Very clever design. I saw somebody made a suggestion elsewhere to cut the rails at an angle to avoid the bump you were referring to. Doing it with your beveling might make for a compound cut, not sure. Sounded like a good suggestion, but I don't have specific experience. Just passing it along.
@BNSF938211 жыл бұрын
Thank you. Slow and steady…
@BNSF938211 жыл бұрын
Thanks Ethan. I had not thought of that. I will keep that in mind, may have to do some clear plexiglas or something like that...
@westrew6311 жыл бұрын
Great job on the bench work!
@lawrencejneuser88013 жыл бұрын
Go to Home Depot. get the sealant called dap, it comes in different colors and is paintable, you can fill all the voids plywood leaves when it is cut. Your bench work will look fantastic.It comes in a caulking tube.
@BNSF938211 жыл бұрын
Thanks Penn. I did do a little fine tuning after the video was posted. From what I can tell on my test runs, it works pretty good. I hope to have some more track added this weekend to run a longer train over it.
@westrew6311 жыл бұрын
Did the screw ideal like you...turned out nice. Thanks for video!
@pacbeltrr387 жыл бұрын
That didn't even make sense. What language was that?
@BNSF938211 жыл бұрын
Thanks Steve. I'm already thinking of changing it to add a crossover... Not sure just yet. I'll keep everyone updated as I find time to work on it.
@fklenda11 жыл бұрын
its looking good.
@PennCentral9911 жыл бұрын
looking forward to it!
@rjl1109195817 жыл бұрын
GREAT VIDEO
@BNSF938211 жыл бұрын
I should have an update posted this weekend. Thanks for asking.
@BNSF938211 жыл бұрын
Thanks Vinny.
@BNSF938211 жыл бұрын
Thanks, its a work in progress...
@jimmcnamara38905 жыл бұрын
can you advise on a three rail track "lift-up" section; re. track joining?
@SuperBanana12111 жыл бұрын
Where's the next update????
@johndebaar18036 жыл бұрын
Soms veel te veel de zelfde hsndeling
@rjl1109195817 жыл бұрын
DID GOOD JOB REMOVE SECTION AS THANK YOUR VIDEO AS KEEP GOOD WORK ON LAYOUT