Flysky FS-ST8 Radio and Beier SFR-1 Full Install in Tamiya 1/14 Truck

Installing and setting up the Beier SFR-1 with the new Flysky FS-ST8 radio.
My website: hobbyconcepts.net/
Link to SFR-1 Starter Package: hobbyconcepts.net/products/be...
Link to modified Flysky FS-ST8 radio: hobbyconcepts.net/products/fl...
My email: [e-mail]
Hobbyconcepts Facebook page: / hobbyconcepts-20961911...
Tamiya Open Studio Facebook Group: / 648718772583781

[@CarminesRCTipsandTricks]

I'm really wondering why I didn't start with the SFR-01 in the first place 🤔 I didn't know HOW good the built-in ESC was, until I saw a Video on setting up the ESC functions! The running possibilities are phenomenal!!!

[@Duraltia]

@46:35 Watching this for when I configure the SFR-1-D Tank Module for my E-100 in case I might get some use out of it since they're essentially the same in how they operate and are being programmed... As far as I know the *_Additional Sound 1 & 2_* are kinda special compared to the other ones in that they _can_ have a Start, a Loop and an End all tied to one action regardless of how long the action is being triggered. The action would begin with Start then move onto the Loop which gets played until you release the action and finishes with Stop. On a Tank, you'd use it for something like an MG fire where Start could play the cocking of the Firearm, Loop would play the actual firing sound and Stop would either be the Echo of the shots or the plinging sounds of casings falling to the ground. In the provided Profile those 3 Sound Pieces sounded off because you were using only one, not the three together ( just a wild hunch though as I cannot test it right now 😉 )

[@The-Warm-voice1359]

Awesome job MR BOB And fantastic set up for the programming.👍 greetings from your Dave🤘

[@jbalia1]

I love the sfr-1 and the flysky fs-st8 took awhile to learn thank’s Bob

[@Gerard8]

Thanks for this video Bob! Together with the Beier SFR-1 Part 1, 2 and 3 this completes the whole yourney of assembling a truck! It is my first truck and I wouldn't know how I should have done it without your video's. Enjoy your holiday ;-)

[@timvanasen6711]

Awesome build Bob too badd this platform was discontinued thank's for sharing 😉👍

[@Gaptist]

Thank you for all these videos and explanations… life saver!

[@All_RC_Fun]

Amazing. Thanks for the detailed info.

[@MaxxPainII]

Thanks Bob for the awesome video. I have been duplicating your video to my setup. Also, the new radio is such an improvment over the FS-I6. I really like all the new changes. It feels good in the hands, nice and smooth, the menu is easier to navigate, the vibration is cool. 👍 Ohh and the Truck looks awesome too.

[@HobbyconceptsLLC]

Thanks, and yes the new radio is super nice. Works great with the SFR-1

[@makewithmegma]

🔥💕👍

[@cgdoublezerorc]

Is this software available for Mac? I always enjoy your videos. I stepped away for a few years ago but trying to get back into RC. 00

[@pingstag]

👍

[@garymurphy5133]

How would this be Wired rx/servo wise if not using s-bus?

[@johnrainbird1155]

Hi Bob great video. Just wondering if I can pick your brains ? I’ve just built a scania 770s and added a MFC03. Also I’ve got a fs st8 standard version transmitter but I can’t get it to work. Any ideas please. I’ve had lights flashing and steering working but nothing else. Regards john

[@HobbyconceptsLLC]

The FS-ST8 has a different name for dual rates. They call it "conditions". Go to the conditions menu and set channel 2 and 4 to 75% switch up and 100% switch down then assign switch a to change the conditions. After you get than done then re MAP to the MFC.

[@johnrainbird1155]

@@HobbyconceptsLLC Thanks I’ll try that. Regards john

[@ckorzelius9775]

can I download your institutional tuition fee document somewhere?

[@dalecripps1291]

can this be programed into a MFC-01light & sound

[@HobbyconceptsLLC]

The MFC-01 does not allow for any additional programming. The MFC is easier to setup than the Beier SFR-1 but the Beier is superior in every other way.

[@speckledjim_]

Is the new ST8 any good for tanks? Does it have pots? Thanks

[@HobbyconceptsLLC]

It would be awesome for tanks. Has 6 fully proportional channels and 4 that can be either push button or 2 or 3 position switches.

[@speckledjim_]

@@HobbyconceptsLLC it looks brilliant

[@Rtx_Fred]

I have a question what servos do you use ?

[@HobbyconceptsLLC]

I use these: hobbyconcepts.net/products/1-14-rc-steering-shift-servos-metal-gear-for-tamiya-king-hauler-cascadia?_pos=4&_sid=a7ec393fe&_ss=r