Your instruction is excellent. You're very clear, articulate and just do a great job of explaining needed details in a way that is simple, yet complete. Well done!
@Jeffopar Жыл бұрын
You forgot the part where you inadvertently spray 5606 all over yourself and the shop. You then walk in the house only to get yelled at by your wife for smelling so bad.
@Jsnckr Жыл бұрын
Serviced a brake on my Cessna 150 after watching this video. Thank you!
@timlinerud77217 жыл бұрын
We use a different procedure for racing brakes, but the remote reservoir above the Master Cylinder is used to add the fluid, and you either vacuum the fluid/air out of the lowest bleed valve, or the 2 man job, is to have 1 person pump up the pedal until firm, then hold and continue pressure, while somebody else opens up the bleed nipple on the caliper, with a tube into a bottle of brake fluid, and you evacuate the air out of the system, from the top to the bottom. This assumes that you have access to the reservoir on the master cylinder, which it doesn't look like your Matco system provides.
@aero_pilot9234 жыл бұрын
you can use external reservoir (MCR-100) but you then need to use MC-4's wich has 2 ports - one for the line the other for the reservoir
@averydzos55923 жыл бұрын
Can you add a link for the filler bottle from Amazon?
@mostefatayebcherif67985 ай бұрын
Hi sir , thanks a lot for this crucial information and practical knowledge
@loveplanes Жыл бұрын
Thanks a lot! This is exactly what I was looking for!
@1shARyn36 жыл бұрын
Matco (now) says do NOT use ANY DOT brake fluid --- you are to use MIL- PRF- 5606 or MIL-PRF-83282 only Vans systems typically require a full pint
@richardhoward5263 жыл бұрын
Great job. That cleared up any questions I might have had 👍
@laurenvancourt12362 жыл бұрын
Thank you. This was great.
@johndecker33062 жыл бұрын
Thank you for this.
@jzawodn6 жыл бұрын
We have the Matco PH-1As on our SuperSTOL and I'm stick of dealing with the pastic (that's what I call 'em) brake lines. Looks like you have some great Russel lines on there... what size/type are they? I'm really tempted to replace ours. Thanks for the video!
@SacksGarage Жыл бұрын
Do you have a source in the US for the plastic (nylon) lines that are common in European LSAs?
@naomingimba2343 Жыл бұрын
very clear. thanks
@tonyconcepcion79502 ай бұрын
Thank u so much
@tonyconcepcion7950Ай бұрын
Thank u
@maheralazzawi78143 жыл бұрын
good job
@maniagokm31867 жыл бұрын
Did I see teflon tape on some of your connections? If so, oops, nono. Just like with fuel lines, thats a disaster waiting to happen. Locktite 567 is (usually) the best ticket.
@gerryvandyk55517 жыл бұрын
While this is good advice, the fact is, teflon tape used INCORRECTLY is a problem, while teflon tape used CORRECTLY is perfectly safe. If you wrap the tape only on the threads and don't let any wrap past the nose of the NPT threads it will work as it's supposed to. That said, the white hydraulic thread sealers are much more difficult to get wrong.
@savethedeveloper7 жыл бұрын
very nice thanks
@jhaedtler5 жыл бұрын
Who ever installed your cotter pins needs to be fired!