Homemade Water Well Drilling Machine (built from parts of half Forklift)

For more DIY Videos press the link ..
• SIMPLE HOMEMADE ELECTR...
And here ....
• MAKE A USEFUL DIY TOOL...
Homemade Water Well Drilling Machine using parts of half forklift
by Mr.DK DIY
SUBSCRIBE LIKE AND SHARE !!!!
My FB Mr. DK DIY page: / youtubecrator
My Twitter page : / dejan_bmb
My Instagram : / mr.dkdiy
All of my DIY videos I have done for experiment and my challenge, if you make these videos at home and something happens to you I will not be responsible for anything !!!
Welcome to Mr. DK DIY channel
My channel include of guiding videos:
-DIY
-How to make
-Awesome ideas
-Tips....
#mrdkdiy #waterwelldrillingrig #diywaterwelldrillingmachine

[@MrDKDIY]

Thanks for 140 000 SUBS to ALL ,Thanks for support my job, thanks for support my KZbin channel ...

[@MrDKDIY]

kzbin.info/www/bejne/pnOzlKt-nap_bbM My NEW DIY KZbin video No-Contact DIY Hand Sanitizer Dispenser.. Like Share and SUBSCRIBE @Mr. DK DIY

[@vity8126]

to what depth can it drill?😮

[@fredz5125]

Hi...what kind of gearbox or speed reducer did you use? How to make the water inlet function

[@draganculibrk4343]

As someone who made several drilling rigs I feel free to criticize your work. Idea isn't bad but poor design. 1. There is no cooling fan / radiator for hydraulic oil therefore oil will overheat and loose viscosity / power 2. There is no pull down force on carriage so you will need eternity to drill trough any a bit harder formation 3. There is no stabilizers to level mast and prevent tractor moving 4. Drilling table is for laughs and with more weight (drill rods) you would end up dropping them in the hole. So to improve this add bigger oil tank with radiator and mount it on the back of the fixed part of the mast. Second issue will need hydraulic cylinder rework (or replace with) into bidirectional and adding chains + sprockets on proper positions to make it work. And yes it is possible but you need to figure it out yourself. Third - add hydraulic or mechanical stabilizers. Forth - make strong and stable drilling table, use inserts so you can stabilize pipe rotation as well and perform faster pipe break out without using wrench etc.. p.s. Didn't see what kind of bearings are used in gearbox if not proper you may end up ripping shaft out with bigger load.. Best regards from Serbia!

[@MrDKDIY]

Brate hvala za tvoj trud sta si vlozio da napises na engleski jezik sad Mozes isto to da napises I na srpski pozz iz Makedonije 😁👍

[@draganculibrk4343]

@@MrDKDIY Hahaha pa super. Meni je engleski skoro pa maternji tako da nisam ulagao trud ali sam ti dao dobre savete kako da unaprediš mašinu.

[@draganculibrk4343]

@@MrDKDIY 1. Nemaš hladnjak za ulje. Ugradi veći rezervoar + hladnjak za ulje. Stavi na leđa tornja tamo gde ne smeta pokretnim delovima. Ulje kada ti se pregreje gubi svoj viskozitet i samim tim gubiš hidrauličku snagu poslatu sa pumpe ka potrošaču. 2. Nemaš pritiskanje na dole za bušenje. Kada naiđeš na tvrđe formacije trebaće ti mnogo vremena da probušiš. Kroz glinu i pesak možeš da bušiš brzo i bez pritiskanja ali ako naiđeš na neki tvrđi sloj kao što je peščar na primer tu si završio sa bušenjem. To da središ trebalo bi da doradiš (ili zameniš) hidraulični klip da bude dvosmerni, da ugradiš lance i lančanike preko kojih ćeš pritiskati na dole. Izvodljivo je u potpunosti samo treba da skontaš kako. Ako te to zanima više o tome guglaj "TELEMAST" i videćeš kako radi. Koriste sajle i koturače umesto lanaca i lančanika ali princip je isti. 3. Nemaš stabilizatore (stope) dodaj ih da možeš iznivelisati toranj kako bi bušio pravo i da ti se traktor ne pomera. Ne mora hidrauličke, možeš i mehaničke kao što su na primer stope od kamionske šlepe. Drugu osu šteluješ na toplingeru da bude pod vaser vagom. 4. napravi jači radni sto da ti bušaće cevi ne završe u rupi. Na radnom stolu napravi centralnu rupu koja će voditi cevi i smiriti ih da ne bacaju tokom rotiranja a možeš i napraviti "klešta" od dve polovine kruga sa konusom koju ubacuješ u centralnu rupu i koja ti drže cevi da ne mogu da propadnu i da se ne okreću kada rastavljaš cevi radi vađenja. I poslednje nisam video na snimku kakve ležaje imaš na osovini reduktora koja vrši rotaciju, Ako nema odgovarajućih (aksijalnih) ležajeva može ti se desiti da teret iščupa osovinu iz reduktora. Čak ti ni ne treba mnogo cevi u rupi za to, dovoljno je da malo zaglaviš "burgiju" u toku bušenja i kad kreneš da dižeš osovina ispadne iz reduktora i eto belaja... Poz

[@joeltems5535]

Please Dragan Can i get you in box?my mail IS [e-mail]

[@alhaah777]

Your right.

[@michaelangelodiga7065]

you prety smart and good there guys. i want to create one too. can you send me the list of equipment you used sir. except for the tructor. thank you so much sir😊

[@luckyguero1972]

That's pretty smart of you guys good work

[@egonhusk8497]

Wow! Wish I lived next door. Where can I find the extended version with voice in it? Works like a top drive, with pull down all came together nicely via forklift, genius!

[@lingyoushi3606]

Nice 👍

[@daoudsir9500]

Can you post the plans of this machine plz

[@D.S.deelldar2061]

Yah machine kaha milega

[@me4taki9oh]

oil pump

[@timerickson7056]

see this ingenuity can't be taught . it's a dying art passed from one generation to the next. this kind of problem solving I learned from my Gramps and he learned from his father. the generation prior to me was not interested in this art. I remember 45 years ago people called me MAKEDO as a derogatory nickname. because I could fix things to accomplish what I needed to do. change a head gasket along a interstate during rush hour using a star wrench vice grips a crew driver .I think that's it. stuff I had in the trunk .

[@MrDKDIY]

👍👍😁😉

[@ЭргешалиАвазов-э8ъ]

Суппер, молодец

[@crushsand1646]

Great job of piecing it together.

[@PACEDARTO]

Very useful tutorial greetings from Indonesia

[@MrDKDIY]

👏👍😉

[@MasterBuilderofTruth]

She likes to party! I’ll tell ya that much for free

[@EmmanuellaTabe-xw6ky]

where can we see the video you assemble the machine

[@pinetorch8181]

Some tongs would be a better option than the pliers & a better set of slips

[@لاإلهإلالله-ف1و]

How to make

[@ТалантКудушов]

Ушундай станок канча турат кайдан тапса болот

[@ibrahimishek4741]

جيد جدا👷🖒😊😊😊😊

[@raulraulph7901]

⭐⭐⭐⭐⭐ Congratulations on your project to build a drilling rig, please send me an answer with complete technical features. Don't forget you are a winner.

[@MrDKDIY]

Thanks bro 👍💯

[@inocenciomadera4880]

Good video

[@josebobe8154]

👍

[@roseowinyo9893]

If i want....how much ...price digging a bore hole at home

[@alcaptainhesham1973]

Good

[@cpark2570]

*salute*

[@michaelapel6341]

Tolle Arbeit..👍

[@hakansavas5553]

Were they your uncles.

[@daimlercherwaken7575]

Wow i am so impress with this good job! Im wondering how did you do this.

[@ajimenezjimenez170]

Amazing , very nice and quite safety

[@MrDKDIY]

Thanksn

[@pinetorch8181]

Damned good idea

[@ТалантКудушов]

К

[@hichamhicham-xy5dw]

Is this well drilling machine for sale

[@hichamhicham-xy5dw]

The drilling machine is very, I hope you have one like it

[@barathguru4238]

How much cost of this

[@riderronp]

Looks like a short tower of a old pro sonic. Probably a Spider?

[@malaychatterjee2732]

Kuwan katane ka machine kanha milega ??

[@Ujangjarambah495]

Kereen bos

[@hizaismail1744]

ممكن سعرها

[@abrisam1353]

greetings from Indonesian drilling

[@morka7079]

Masine comyer

[@anildadhe4323]

Hi

[@kirilkirca2219]

Do kolku max mozi da se busi?

[@irfanrahaman3490]

Pls cont mobile no

[@abcxyz8936]

Very good work

[@sahmad5456]

Awsome wonderful excellent....

[@DarshanKumar-mh6cq]

Yeh kha par milega

[@hichamhicham-xy5dw]

Hi . How deep can you drill in wells?

[@2010Evropa]

штанги можно уронить !!!