Make DIY Boost converter 3.7v to 12v, Step up voltage adjustable converter

[@BuwanajithManthikaDeSilva]

Thank you very much bro❤ Its working very well🎉 I made a super bright emergency light with this💖💖👍👍

[@homemade_101]

welcome bro thank you.

[@ebenezerbennie7824]

@BuwanajithManthikaDeSilva good evening bor can you please help me with this electronics

[@homemade_101]

Adjustable power Supply: kzbin.info/www/bejne/Z6WtqaB3pZhpeck

[@howtomakemoneyonfacebookpa2747]

Can it give constantly output 12volt 5a in small load

[@homemade_101]

@@howtomakemoneyonfacebookpa2747 yes try

[@nanfwangdabiring1520]

From the video , at 7:39, the multi meter is showing a current of 0.3A while the bulb is rated 12v 10w. This goes to say that, this device is coughing out just 3.6 watts hence, the low brightness 🔅

[@dhodkundechandru6219]

Good but amp.kaise badhaye.please reply.

[@homemade_101]

5A

[@dominik_kuznik3994]

The guy who had 68v on the 35v capacitor was lucky that the capacitor didn't explode, put a higher voltage on the capacitor and if the coil squeaks, it means that it is very loaded and the coil probably has too low a maximum current, if the coil gets hot, change the coil

[@homemade_101]

[@darkmatter369_]

😂 current bahut kam hai 35 v 2200uf 35×2.2 =77 volt tak ja skta hai agar amp 0.5 ho

[@mrdiytech]

1 st good video and experiment

[@homemade_101]

welcome and enjoy

[@Aaliyah21]

Good job 💥🤟🤟 ...thanks for shearing 🙏💛

[@homemade_101]

welcome

[@d1vinespirit914]

Hi, i want to ask about the components that are used, irfz44n mosfet, 220 ohm Resistor, 2200uf/35V capacitor, what value of inductor and diode or which type, and 10k pot? And how can i decrease the output?

[@oANlWgf86GQkQC_PLUS_MJhAM]

works great! BTW, i was wondering, if I use a lower trigger voltage MOSFET, would it be capable of stepping FROM lower voltages? say, 1-2.5V?

[@homemade_101]

Yes you can!

[@sumitd4u]

Can i use this to boost voltage from 18V Solar Panel dc voltage to get 300V Dc so get ac 230v Product can run ??

[@hubbyflashgaming5700]

​@sumitd4u Not all devices are capable in powering house appliances. They run on AC but you can use light bulbs and phone chargers on DC.

[@acayedenis]

Great work mine boost to 76v without potentiometer from 3.7v but drops as soon às i put even a simple load and doesn't work why?

[@homemade_101]

🤔

[@CreativeElectronics1234]

@@acayedenis because of very low amp in output

[@acayedenis]

How do I correct the low amp in output is it the transistor I used which was TIP 122 causing broblem help me bro please

[@BabuSora-ch4on]

Work kar raha hai bro😊😊😊

[@homemade_101]

thanks borther

[@atec9228]

Hi again, I have 0.6mm of wire. How many turns i can use for the inductor?? Thanks for allí. Great proyect

[@homemade_101]

40 runs all 20T 0 20T

[@Bhavuk_Varshney]

Is it necessary to use potentiometer in this project?

[@homemade_101]

YES

[@BelovedMaximus]

Nicely done 👍 how do I make one to convert from 5v to 12v thanks in advance ❤

[@homemade_101]

Please wait

[@BelovedMaximus]

@@homemade_101 ok thanks

[@hubbyflashgaming5700]

you can use the same circuit to convert 5V to 12V. Use the potentiometer to adjust the output voltage to 12V, then add a 12v zener diode at the output. The current is low but it will still work.

[@hichamtassi1753]

Very nice video ! Can you please show how to make 12v to 48v to make work inverter from battery. Thanks.

[@homemade_101]

ok i will try

[@apkgamer7553]

Can i use " ITA12N65R n channel mosfet ...instead...

[@homemade_101]

yes

[@apkgamer7553]

Yes, it's working now... Thanks 😊

[@hubbyflashgaming5700]

You can use high power N channel MOSFETs to boost voltage without too much heat problems. I used IRFz44N MOSFET for my project. It shorted from a high voltage feedback in the coil bc I don't have any zener diodes to protect my MOSFET from blowing up.

[@ilhammutsakibtsani5135]

If dc input 0.5 volt - 2 Volt DC, what is component can i use for booster converter?

[@homemade_101]

2v ok yes

[@ishl3321]

what mosfet is it p or n type

[@siriuschan1514]

could you pls tell me why is there background noise when the boost is working, where is the sound from and how to decrease the noise ?

[@homemade_101]

it is normal. induction sound

[@khoalodaccau]

can i use z24n or 2x z24n ????

[@homemade_101]

yes you can use

[@khoalodaccau]

@@homemade_101 1x z24n ??? ... BUt thank you so much

[@oANlWgf86GQkQC_PLUS_MJhAM]

can I use a 10A10 or MUR1540G for the diode?

[@homemade_101]

ok

[@atec9228]

Hi, what Is the section in mm of the wire to create the inductor?? And the diammeter of the toroidal ?? Thank you

[@atec9228]

Can you tell me the diammeter of the wire and the toroidal to create the inductor??

[@homemade_101]

1mm, 2cm

[@atec9228]

@@homemade_101 Ok, if i use for example 0.6mm i need to reduce the number of turns or not??

[@kaushalmaheriya]

its not working bro 😢 me banaya ye nahi aa raha output bass 3.30V input deta hu to 3.40V Output hi milta hai potentio ko gumata hu fir bhi not work

[@homemade_101]

This is working well. change inductors and mosfet

[@kaushalmaheriya]

@@homemade_101 kitne size ka inductor use karu

[@প্রতিবাদী-র৫ঝ]

12turn inductor can be bought or made?

[@homemade_101]

made it

[@madhuchakraborty8080]

I can use irf630mosfet for this. Please reply

[@homemade_101]

yes you can

[@madhuchakraborty8080]

Thank you for reply

[@unlimited.sort.]

Can i use irfz540

[@homemade_101]

if it N channel, you can use

[@Memmedov001]

Can I use 4700uF 16v capacitor ,IRF3205 mosfet and 1N4007 diode for this?

[@homemade_101]

yes. but not recommend Diode and capacitor voltage

[@foxeclips9868]

Can I use 10 k trimpot instead of variable resistor

[@homemade_101]

ok

[@bebeyz334]

Ive made it .. But the mosfet cant stop heating.. How can i fix it? tnx bro!!!

[@homemade_101]

It is nomal, use heat sink

[@hubbyflashgaming5700]

Add a 12v zener diode from gate to source of MOSFET to protect high voltage from killing the MOSFET.

[@atec9228]

What Is the value in Henry of the inductor?? Thanks

[@homemade_101]

0.11mH 0.3 Ohm

[@atec9228]

Thank

[@kaushalmaheriya]

is me 12V 1.5AMP input to 12V 5 AMP output circuitdiagram milega sir

[@homemade_101]

No no. 3.7v to 5v input

[@kaushalmaheriya]

@@homemade_101 sir ye work hi nahi kar raha kya karu 3.7 V input deta hu to bass 3.4 hi output aata hai ic bhi sahi hai fir bhi sir

[@century_centure]

Where is that hissing sound coming from. From Capacitor or Inductor?

[@homemade_101]

it is inductor

[@century_centure]

@@homemade_101 Can I supply this circuit with 5vdc if i don't have the 3.7vdc?

[@homemade_101]

yes 5V ok @@century_centure

[@EnglishloverRupak]

I have made it on a zero pcb it doesn't work but when I try to make in open it works properly why it not works on pcb

[@homemade_101]

Maybe your pcb is not correct, check your connection.

[@DibujanteDaniKahane]

HI, I could use other transistors like H22 13866 or P133009 or LT5250 or SB3040PT or RC3009 or MOSFET S20C45C instead of irf3205 ??, thanks so much in advance.. best regards!

[@homemade_101]

can't. MOSFET only.

[@DibujanteDaniKahane]

OK, only mosfet, but I can use MOSFET S20C45C? thanks again.

[@niteshkanere1225]

Inductor value

[@homemade_101]

0.12 mH

[@Irishtheproducerofficial453]

Bro is it possible inverter to work

[@homemade_101]

Not possible

[@Elektrobild2518]

sir, how to make with this boost converter flyback driver?

[@homemade_101]

I think can do it

[@madhuchakraborty8080]

How to make the inductor you used

[@UMANG_GAMING8282]

Ye circuit kitna der Tak chal sakta hai

[@homemade_101]

it is depend

[@edscac5891]

Hola lo hize exactamente igual pero mi transistor se calienta y qué será lo que esta mal?

[@homemade_101]

G-S connect 10K resistor and use heat sink

[@edscac5891]

@@homemade_101 gracias ya funcionó perfecto 👌 un chingon eres hermano✌️👍

[@madhuchakraborty8080]

Dc 775 motor chalage isme please reply

[@homemade_101]

??

[@quatquatdao9885]

Chào bạn.video rất hay.ban cho tôi hỏi đầu vào dung điện đc 12v được không? Xin cảm ơn!

[@homemade_101]

dùng tụ điện 35V

[@issadon7990]

its boos the amp ?

[@homemade_101]

5A

[@FrankEnrique-qo1fz]

How to delete the noise ,that noise every nigth is crazy

[@homemade_101]

it is normal

[@TechTed1]

Use more than one capacitor bcz when the load is higher the voltage drop at 3.7 again

[@homemade_101]

THANK YOUR ADVICE

[@TechTed1]

@@homemade_101 Welcome 😊

[@century_centure]

And can it work with 5v direct from 5.5v Solar panel? Kindly reply to this please.

[@homemade_101]

yes

[@century_centure]

@@homemade_101 I can see you have already answered my question. Thank s alot Bro.

[@shafiqansari4344]

How much ampere brother. Please explain.

[@yigitbilgisayar]

Max current?

[@homemade_101]

5A

[@yigitbilgisayar]

@@homemade_101 thanks.

[@ebenezerbennie7824]

Well done senior man please can we have a private chat 🙏

[@andrimastirta4736]

Nice video 👍, can you give the circuit diagram? And I want to ask, how many winding the inductor? Thank you

[@homemade_101]

Please wait

[@homemade_101]

drive.google.com/file/d/16eFvt-oyOp4ul343Uy-lTJ4bbMdWeu8l/view?usp=sharing

[@hemanthkshatriyas8141]

Hello bro can you make h bridge circuit that convert 310dc to 220v Ac plz

[@homemade_101]

I haven't idea it. I will try

[@nenebaez4145]

Good video, you can share the diagram

[@homemade_101]

OK i will send tomorow

[@homemade_101]

Circuit diagram 👉 drive.google.com/file/d/16eFvt-oyOp4ul343Uy-lTJ4bbMdWeu8l/view?usp=sharing

[@nenebaez4145]

@@homemade_101 thanks bro

[@vipxlegend99]

can i use ti wifi router

[@homemade_101]

don't bbro

[@scorp-5717]

Con eso elevó el voltaje pero si el amperaje es bajo también me funciona para elevar el amperaje lo digo por las placas solares

[@homemade_101]

yes low amper 5A max

[@SharvilSawargaonkar]

How many henery inductor brother

[@homemade_101]

30uH

[@SharvilSawargaonkar]

@@homemade_101 will a 5millihenery work i salvaged it from old cfl driver circuit

[@gustavobrito8813]

Que diodo usas que numero

[@homemade_101]

5A diode

[@mjbunnyt.v5268]

Y it make noise... ?????????😮😮😮😮😮😮😮😮

[@homemade_101]

it is norml

[@sk_pm2004]

Diode ka name kya hai

[@homemade_101]

1N5401

[@นิมิตรดอกพิกุล]

ทำแล้วยังไม่สำเร็จครับ มอสเฟตร้อนมาก

[@homemade_101]

sorry

[@unlimited.sort.]

Use irfz540

[@homemade_101]

N channel, you can use

[@jaylim1094]

I will just buy 2 more batteries 😁

[@homemade_101]

it is no problem 😉

[@TanphatDanh-g4x]

Ok cuon cam khu nhieu tot......!

[@homemade_101]

thank you

[@97no]

35 to 65 ☠️💀😇

[@homemade_101]

sorry

[@educationrepairs]

❤

[@homemade_101]

☺

[@chongshenchang9367]

60v cannot give full illumination to the 12v car lamp...😁😁😁

[@homemade_101]

yep

[@Nation_First269]

3.7v to 12v ❌ 3.7v to 68v ✅ Solution?

[@homemade_101]

i don't know

[@huriblog2957]

Hello baro waht led is no thing real to car light bulb baik indecatr bulb .waht is led .but led 1.5 volt .

[@tomelektronik]

Working volt 2200uf 35V step up 60V DC danger❗ of kapasitor

[@homemade_101]

no, this circuit is safe. use a switch

[@Debiutant]

Маленькая сила тока. Мне больше вот эта схема нравится: kzbin.info/www/bejne/iZC6co2kjcSpb5Y

[@TanphatDanh-g4x]

Bo loc thanh........?

[@homemade_101]

🤔

[@วัฒน์สันต์สนโคกสูง-ฎ3ฏ]

😃

[@homemade_101]

☺

[@aripinpasaribu4946]

Kepala sangat sakit lihat vidio ini karena terlalu cepat bagi saya pemula.

[@homemade_101]

😮‍💨

[@Juliano-le5dk]

Joule thief circuit 🙂

[@homemade_101]

yes 12.6v

[@rezatavan5048]

Ok ❤

[@homemade_101]

enjoy

[@Руслан-т7н8з]

генерация срывается , не показал как мотать в какую сторону и каким проводом . нет стабилизации на выходе . схема отстой! ! ! !

[@homemade_101]

what bro

[@leroyolson4349]

No Good, Where is schematic

[@homemade_101]

this is a very simple circuit.

[@shafiqansari4344]

How much ampere brother. Please explain.