Honda Civic 8 Spaceship Rear Bushing Replacing

[@Snip59]

I put PowerFlex in my Type R 2007 FN not the OEM Honda unit and the difference is superb indeed been in 4 months first change in 16 years wow has it done 100% the best.

[@easylearn9350]

Good video. thanks for sharing. Q: Is that safe to jack up this Honda (hatchback 8th) from the rear axle in the same place you lifted it down at the end of the video (4:32)? any better place?

[@rastislavg2815]

this is good place, helping silenblock :)

[@hanhvu8076]

i have a civic 2009 the similar prolem , so easy ,thanks from Finland , i will do next week

[@waverider5751]

So, how “easy” was it?

[@attilavarro2859]

Hi, couldn't you have taken it out with an extractor? What size silent inserter was needed for the insertion? Thanks for uploading and replying

[@514aam]

You need to tighten them up with the suspension loaded... They will last a lot longer and feel better

[@Matyero12]

Nice video, no unnecessary details and talking. I'm just about to do the same job. Could you please advise about the press tool diameter? Is there any way to hammer it in gently rather than buying the press kit?

[@rastislavg2815]

I don't know, you have to try ... but probably not ... i have this set www.aretacia-rozvodov.sk/stahovaky/matabro-mb-03-06033--stahovak-na-silentbloky-loziska-34-90-mm/?gclid=EAIaIQobChMI2MKrn4jh-AIVDbLVCh0r0gu0EAQYBiABEgLawvD_BwE

[@norm4267]

Szia. Kicserélted? Én is pont ezen agyalok, videó alapján nem túl bonyolult, de azért bennem a para hogy nálam nem lenne ilyen egyszerű.

[@Matyero12]

@@norm4267 Epp ma fogom csinalni es lehet dokumentalom a 8gen csoport szamara.

[@norm4267]

@@Matyero12 Mindenképp tedd meg. Ott is jelen vagyok. 🙂

[@andrejlukac1783]

​@@rastislavg2815 Ahoj, pozerám že máš lisovacie pripravky, plánujem meniť zadné silenty na Type R, odkiaľ si? Nevedel by si mi to pozicat, samozrejme nechcem to zadarmo

[@applelactao783]

Hi. Do you have knowledge if honda city 2009( philippine specs) has the same size of this kind of bushing? Dealership told me they don’t just sell bushing but the whole torsion bar. Thanks..

[@carlosgarciaarellano4864]

I have a 2008 civic. Could you please tell me what are the part numbers you used?

[@rastislavg2815]

that video is old, I don't know

[@mehmetali60]

42100-SMG-E06 or 42100-SMG-E05

[@Matt-uh3mg]

Which torque please ?

[@dani_gracia]

How many nm?

[@thomasedison2179]

Nazdar ako je to náročné časovo? Zajtra mi ich idú meniť. Ďakujem

[@rastislavg2815]

no podla toho jako sa dari😀 takze kludne 2-3h alebo 1 den😀

[@HondaK20]

Rasti..how much time you spend on this replacement? Thanks!

[@rastislavg2815]

3 to 4 hours, if everything goes according to plan

[@robertkrygl]

Hello, please, what was your tightening torque when tightening the screw?

[@rastislavg2815]

180-200 :-)

[@StealthzFX]

Actual torque is 101nm, just do it ft instead

[@borishasarrived5524]

3:48 why so many times?

[@jeffreyevans6892]

How did you find out the bushing was bad ?

[@rastislavg2815]

sound in the car, cracks in the rubber(silenblock), optical :-)

[@ВиталийГорбунов-ж6ч]

На эту работу Я трачу 15 минут за две стороны

[@shaun7126]

You're working too hard. Use a torch heat the rubber then use a hammer to hit the metal sleeve as far as you can then take a vice grip and then twist out the metal sleeve then use a Sawzall to cut the bushing

[@simonjohnhinton1938]

polyurethane bushes are the best, they are stiffer and last longer...