Honda Forza 300 - CVT Removal / Installation (belt/rollers,variator,clutch) | Mitch's Scooter Stuff

[@MitchsScooterStuff]

T O O L S Ratchet 3/8 drive - amzn.to/2hhmnUs Breaker bar 3/8 drive - amzn.to/3lrjIWj 8mm socket 3/8 drive - amzn.to/2xLNVXU 10mm socket 3/8 drive - amzn.to/2xGuLSF 14mm socket 3/8 drive - amzn.to/2xGn4Ms Phillips no. 2 screwdriver - amzn.to/2fgdZDL 17mm socket 3/8 socket - amzn.to/2EMT6LO 5mm allen socket 3/8 drive - amzn.to/2ofCuCg Variator / Clutch holder tool - amzn.to/2ZuYJEA 3" / 6” extension set 3/8 drive - amzn.to/2h7ypMl Molybdenum Disulfide Grease - amzn.to/3LpId2z Torque wrench 0-150 ft/lb 3/8 drive - amzn.to/2Crqq4R Brass/Stainless Steel/Nylon Wire Brushes - amzn.to/3Jvi8gW

[@hazy1418]

Thanks again Mitch, this looks very similar to my sons SH300i which the clutch bell is rubbing against the cover, so will be taking it apart very soon to sort out. Your videos are always brilliant and make the average scooter Dad’s life much easier 👍. N.B. I always draw a rough outline of the cover etc on a piece of cardboard and push each bolt through in the relevant place, always handy if you can’t sort out straight away and have to come back to it a few days later due to weather or extra parts etc.

[@GhostFolf86]

Great content there bud,as of Saturday 7-13-24 I recently purchased a new project moped for me to wrench on and the project is a 2006 Honda Metropolitan 50cc moped that has been sitting 15+ years and is in great condition minus the luggage rack but the headlight,brake light,turn signals,horn,speedometer work and she has 1,371 miles on it,it was owned by a friends father in law and he might have passed away so it sat in a barn so I’ve been evaluating what it needs to revive it and I spun the engine over and it has great compression,spark but terrible old fuel in it so I think it just needs a fuel tank flush,new gas and oil change once it’s running and driven a short shakedown lap,luckily this is a 4 stroke motor and takes 10w-40 oil and I happen to have a unused quart laying around so wish me luck with my new project

[@MitchsScooterStuff]

Thank you! Congratulations on purchasing a scooter! Make sure to replace the fuel pump and fuel filter first before pouring in new gas. If you clean the carburetor, you don’t want old, bad gas from the pump and filter getting into the carburetor and clogging up the jets. I learned this lesson from my Ruckus video, haha. Also, remember, it's a scooter, not a moped! 😉

[@GhostFolf86]

@@MitchsScooterStuff I’ll do my best to revive it by using your tips,it ran briefly on starting fluid but I didn’t run it long,I’m going to clean up the fuel lines,tank and sending unit before I put new fuel in, I also rebuilt the carburetor by cleaning up the jets and float ect,she’s a beauty and only paid $300 dollars for the scooter and I can’t wait to make a follow up video of it running and driving

[@rolacook222]

THE BEST VIDEO for changing out a belt, bar none! GREAT JOB!👍🏻

[@MitchsScooterStuff]

Thank you!

[@farmoboy83]

new skill learned to install easily the belt on the clutch! i used to put a screwdriver with a rubber sleeve between plates but using hand and the foot looks like a lot easier!

[@MitchsScooterStuff]

Oh wow! Yeah hands and foot make a job so easy, try it next time 😄👍🏼👏🏼

[@Serpico1152]

Great maintenance video as always Mitch, I often refer to many of your simple and to the point videos when performing similar maintenance procedures on my '96 Honda Helix. 👍

[@MitchsScooterStuff]

Thank you so much! Psst, watch out for helix videos soon! 😉

[@Serpico1152]

@@MitchsScooterStuff I can't wait to see them!!! 😊

[@motobc2251]

Thanks so much! Excellent content so great to see more Forza content. It’s next on my list for replacement now.

[@MitchsScooterStuff]

Great to hear! 😄🙌🏼

[@bigmikeshooter]

Great as always. Cheers from Greece.

[@MitchsScooterStuff]

Thank you! Cheers!

[@brendanstorey7005]

Great job🌟🌟🌟🌟🌟

[@MitchsScooterStuff]

Thank you 🤗

[@aedwards4496]

Hi Mitch, do you have any video's on Burgman AN400 head bearing replacement? thank you.

[@MitchsScooterStuff]

Hey, you mean steering head bearing ? I don't have video on burgman yet but I have video on Vespa LX front fork removal and installation, maybe that gives you idea what it looks like?

[@alanedwards6285]

​@@MitchsScooterStuffgreat, thanks Mitch.

[@motowolfnorway.k.e.b.8005]

Nice video👍🇳🇴

[@MitchsScooterStuff]

Many many thanks

[@mrmoon1482]

Hi Mitch do you have the torque settings for variator and clutch nuts please,

[@MitchsScooterStuff]

Hey make sure to turn subtitles on 🤙🏼

[@NuYoRicanFlava]

Hey Mitch, would you happen to have a link to where I can purchase that extender for the clutch holder tool you're using at 5:37 please?

[@abnerbjorn1106]

Try a piece of old steel closet rod, or 3/4" copper pipe.

[@MitchsScooterStuff]

it was a piece of stainless steel pipe I cut off on a project... just use any pipe will work :) like a guy just commented to you too

[@andreyg807]

Спасибо за позновательные видео и за субтитры на русском языке.всё очень понятно и наглядно...😊

[@MitchsScooterStuff]

You’re welcome! 😄🙌🏼

[@andreyg807]

Скажите пожалуйста,купил новый вариатор и есть два небольших скола на чашке,не повредят ли ремень эти царапины??

[@MitchsScooterStuff]

How big are the chips? Chips like bowl shape, feel them with your finger, if chips scratch your finger then it’s bad

[@andreyg807]

Спасибо за совет,проверю.​@@MitchsScooterStuff

[@andreyg807]

@@MitchsScooterStuff острых нет сколов,небольшие углубления гладкие...

[@sandwaves5642]

Much heathier to use YOUR OWN weight to lock/unlock heavy bolts, instead of, potentially, overloading + damaging your back - pushing from down - up !!!

[@MitchsScooterStuff]

Thanks for the tips!

[@farmoboy83]

the plastics and variator case looks really in bad shape. My sh300 is 80000km and 13 years and looks like new in comparison

[@Serpico1152]

It's most likely caused by the intense sun UV's & Maui salt air atmosphere.🤔

[@MitchsScooterStuff]

this is what I am going to say and the owner didn't really wash it often, he dropped it off very dirty and I washed it real quick before filming... need to polish and wax