Honda Outboard Timing Belt Installation Part 2

[@robertwalker3168]

Brilliant video, I'm not surprised there aren't many timing belt videos on youtube. Super job guys

[@MikeTLive]

this is an excellent well paced video. surprised no mention of the timing marks which were clearly visible and happily aligned :) i'll go back and watch part1

[@MikeTLive]

HA! i should have listened a little more- as you then mentioned it on this one. awesome

[@tri-logicrhythms2265]

MikeTLive Thank you Mike, I painted the alignment arrows white so that this could be clearly seen by the viewers. A lot of time filming and editing. Not too many manufacturers showing similar videos.

[@MikeTLive]

Tri-Logic Rhythms your effort really shows in the finish quality. And part one did not disappoint! It too is most excellent. As expected you point out setting at TDC before breaking it loose

[@MikeTLive]

You haven't found a good video for tearing down the carburetors have you? Mine sneezes and having trouble with low idle. I'll be replacing the fuel pumps this week. One is leaking hope it's the cause.

[@tri-logicrhythms2265]

MikeTLive , I purchased a set of vacuum gauges to calibrate the carburettors and the results were impressive , may be worth doing after you replace fuel pump

[@mikeinwoodlands7854]

Thanks for your video! Well done. Have watched a couple of times now with my manual.

[@sealtite904]

Killer 2 part video! Thanks it helped a lot with my timing belt replacement!

[@ianr5978]

Great Video, a lot of effort to produce I imagine... I have a Honda BF50D coming up to 4 yrs old now so will be doing the timing belt as you did, will order the parts, a pulley holder and the appropriate SELOC manual in the next day or two.. I will be doing other jobs such as the impeller too, once again , your video on that subject has given me the confidence.. I wouldnt think there is much difference in the mechanics of your engine to mine..

[@tri-logicrhythms2265]

Ian Roberts , hi Ian , I believe the BF 50 may be a counter rotation or an anti clockwise rotation of the shaft , please confirm this before you attempt to loosen crank shat bolt , it will say in seloc manual.

[@n.r.389]

This was a very nice video and perfect explanation. Thanks a lot.

[@carrozzeriafilippini1266]

Thanks for the brillant video you made. I've also a Honda Bf90a and i'm going to sobstitute the timing belt. I didn't quite understand how many Nm the roller pulley bolt should be locked to. Do I have to do a few laps or after how long should I check the timing belt tension by loosening the tensioner bolt?

[@kenmazza1494]

Getting ready to do it on mine. Great help Many Thanks

[@pauladams2955]

Great video, thanks for sharing.

[@physiopdw]

That great, you are welcome, glad it helped!

[@paulwebb3240]

Thanks heaps for posting this video , very helpfull

[@tuomas2317]

Thank you for the video! Do you think i can change my honda bf50 2008 timing belt as shown in your video?

[@petertlr1644]

I’m not sure but it should be similar. Best to get a Seloc workshop manual.

[@davehaylock1370]

great vid ole mate,what is the time between changes recommended by honda.my bf 90 is 16 old,with origanal belt.thanks in advance.

[@petertlr1644]

All about condition and wear and tear, the tensioner can give up before the belt if it begins to rust and mine was worn, that why I changed it , belt was in good condition when I removed it . Honda don’t say when on any manuals that I have seen only inspect regularly, 😀

[@davehaylock1370]

@@petertlr1644 thanks good advice

[@cedricdurand1426]

Thank you Peter !!

[@cpborrelli]

Great Video

[@tri-logicrhythms2265]

You are welcome Mike!

[@michalpatela8600]

VIDEO IS ON MY PROFILE THANK YOU

[@almarnordby2034]

Thanks 😀

[@michalpatela8600]

HI WE GOT PROBEM WITH HONDA ENGINE KNOCKING I WILL ADD LINK BELOW DOES ANBODY HAVE THE SEAME PROBLEM ? HELP NEDEED THAN YOU @

[@edouardblard14]

Mon moteur Yamaha 60ch quand je mais en marche pour chauffer le moteur au bout de4minute la larme se déclanche ces quoi le problème svp

[@edouardblard14]

Une réponse svp

[@edouardblard14]

Bienvenue dans le presse-papiers Gboard. Le texte que vous copiez est enregistré ici.

[@petertlr1644]

Edouard, you need to service the water pump / impeller , because your engine is probably overheating !

[@sylvysweeney3676]

A