Worked like a charm. RX4s are a little bit finicky but if you can get them set up just so, they are the best!
@kkkwwwaaakkk5 жыл бұрын
This is also the best method to bleed Shimano's road brakes
@cs8sz3 жыл бұрын
Brilliant video thank god! I was a bit of a loss with these calipers
@dirtyparsnip14552 жыл бұрын
Brilliant video very happy, easy to follow 👍🏻
@bikedoctor19482 ай бұрын
Builded on a new Legend By Bertoletti titanium frame, soon pictures on my insta really beautifull calipers RX4 and far better than the original....
@motheexplorer4 жыл бұрын
So it looks like I need to buy a 5mm adaptor for the funnel at the lever end as well as a 5mm adaptor for the syringe end at the caliper? Is that right?
@keithcameron19211 ай бұрын
These are by far the best brakes I've used. However, they're a pain to set up, a pain to service and the pistons frequently get to a point where they don't retract properly. If you're a keen home mechanic they're a good choice but they're not fit and forget that's for sure.
@orange5fox3 жыл бұрын
They don't mention it in the video, but be very careful when tightening the lever bleed screw, if you overtighten it , it'll bind and virtually lock itself into place. If you then try removing it with a normal hex key, you'll probably round it out,if you use a Wera hex-plus (like in the video), you may be lucky, and avoid having to butcher it
@r0m0pr02 жыл бұрын
This happened to me ... I had to extract the bolt and had to buy a new one
@Spellcheekswammablamma3 жыл бұрын
Hi there, thanks for this video. I’m curious if the Shimano 2.5 mm housing will work with the RX-4 calipers. Thanks
@ARGINH2 жыл бұрын
Yes the standard Shimano hose will work fine.
@FUBuddy4 жыл бұрын
Where do I get the threaded fitting at the end of the syringe which attaches to the bleed port? That part did not come with my RX4 calipers.
@robincooney12634 жыл бұрын
Yep, you're right. I bought a kit with a syringe with the threaded end (make sure it is the Shimano kit)
@ioannidesalex2 жыл бұрын
These calipers doesn't give the extra brake rotor clearance that cyclists are asking for swapping form shimano or sram to a third party brand.
@thecappy3 жыл бұрын
What about alignment? Fucking thing rubs all the time.
@lanceblack888 Жыл бұрын
What a faff! Bring back rim brakes!
@HollingworthTim4 жыл бұрын
Where do I get the threaded fitting at the end of the syringe which attaches to the bleed port? That part did not come with my RX4 calipers.
@FUBuddy4 жыл бұрын
this is what im here for.
@jhbiddle4 жыл бұрын
@@FUBuddy You need a 5mm threaded attachment to the syringe - you can find lots on Amazon or eBay very cheap. Shimano bleed kits I believe are 4mm, while SRAM is 5mm. In the video, it looks like they are using a RockShox Reverb bleed kit (the seat post also uses mineral oil). I'd be careful not to directly use a regular SRAM bleed kit since they are DOT fluid instead of mineral oil. Hope that helps.
@FUBuddy4 жыл бұрын
@@jhbiddle it does indeed, thank you very much sir.