Hot Tub Leak Repair with Fix A Leak

Fix a hot tub leak with fix a leak. I used 8 oz for my hot tub..use 32 oz for pools.
How much is an 8 oz bottle & other info: amzn.to/3fIcesF
For a 32 oz bottle: amzn.to/39a8zBz
Disclosure: This post may contain ebay or amazon affiliate links, meaning I get a commission if you decide to make a purchase through my links, at no cost to you.

[@beverlyan]

Wow, what a comprehensive guide! It's evident that you're experienced with these setups, and this video along the way was super helpful. Thanks for sharing this informative video!

[@beverlyan]

I was wondering if you're interested in collaborating on a hot tub thermostat.

[@st-qp4mr]

Glad it was helpful!

[@beverlyan]

@@st-qp4mr Are you interested in testing a hot tub thermostat?

[@bobbernard8521]

No need to fill your tub back up as long as your water level is higher than all your jets! After removing your filter(s) I place a long nose funnel into the intake and pour the desired amount into it while running my system, this way 100% of it goes into your lines! Let my tub run for about 5 or 10 minutes and completely shut it down (Unplug it) for about 48 hours. At that time I drain it and wipe it down, refill it and I'm off to the races! Been using this for about 5 years and do it once a season. Most of your leaks usually are worse in the spring up north, everything shrinks in the cold, once weather and tubs heat up, everything expands and tightens up and water loss usually isn't as severe. Good Luck, PS: I usually purchase the 32oz bottles, and there's no need to use more than about 10-12oz an event.

[@davidsheward2113]

Suguest you read the entire instructions from Marling's website. This is not intended as a "dump & go" fix. For best results: After a day or two running the pumps (6 to 8 hours) you need to drain the tub completly, clean up any residue, and then allow the tub to sit (dry) for several days for the product to cure. The only thing not covered by the website directions but I was told by my "tub guy" that recomended this product is that durring the "run process" use a mop to mix the compound back into the flow from the bottom of the spa as it is heavy and will settle to the bottom of the tub. He also recomends that after the curing (dry) period and cleaning to fill & flush the tub twice. First time using the old filter (to trap any of product that may be left in the tub) and the second time with a new filter. I haven't done my yet as he also suguested to do this after the weather gets warmer for best results. Fixaleak also recomends above 40 degrees min outside temp & at least 70 for water temp. My guy recomended 100+ works best for water temp. i.e. Operating temp. My tub is 400 gal & I am going to do the 32 oz treatment on a level loss of just under an inch per day leak.

[@gagethompson8529]

Did it work?

[@mrotsteiuq]

Any update or changes to your plan?

[@ADJPoirier]

Did you try this ? I have a similar rate leak.

[@thecuss6817]

I've had a 1988 CalSpa since new. One side is 8" from the block wall of the house, think that's where my leak is. So I've been using Fix-a-Leak once or twice a year for past decade, works for me.

[@roblox34306]

I added this product into my inground pool and it stopped the leak instantly Awesome product

[@rudarbusa3314]

How much did you put on it?… my pool is 25k gallons?

[@toddmurat2673]

May the Hot Tub Gods smile upon you. WOW, this stuff really does work. I have it too. Thank you!!

[@mohshafie928]

You removed the filters, yet in the final shot the filters were on? how long did you run the pump cycle without the filters?

[@constantreader7944]

You skipped what I thought was the most important part. I thought the last step was, you drained the tub, and let it "cure for 2-3 days before filling back up the tub. Any reason you didn't do this step? It's on the instructions. By the way, I love this stuff. I have a 23 year old spa that was top of the line in 1998. Started leaking in 2015, but it's otherwise a terrific spa. So with this product, using it once or twice per year, are six years into it with no leaks. Lat time lasted about 18 months, then over a two week period, the gunk started coming lose. Leaked again. I did the Fix a Leak process, and no leaks. Like I am saying, this is not permanent, but it does extend the life of the spa without expensive repairs.

[@constantreader7944]

Oh, and yes, like others have said, it often takes more than 8 ounces to work. I buy eh 32 oz bottom off amazon for $25. What a deal. Oh, and finally, if this doesn't work for you, you have a really serious problem that needs professional repairs or replacement. Remember, spas aren't designed to last more than 15-20 years.

[@jackdawson3276]

What brand hot tub?

[@RoseFrey]

😂you also need a clean filter, it will definitely help the water flow your pump is struggling to have. No wonder your gaskets are falling..hopefully you are changing your home furnace and AC annually so the pumps and motor aren't struggling as well

[@RoseFrey]

Didn't miss anything, but you definitely need to get better filters hygiene and replacement, clogged filters on your spa, car, lawn mower mower causes your pumps and motors to strain, didn't miss anything, hopefully you are taking care of your car, lawnmower furnace AC etc better 😅

[@katiecurtis9902]

Do you have to have the water to temperature?

[@jerryjones2215]

Wow! How is it that I've never heard of this stuff before??? I've always been dead set AGAINST using stuff like this in vehicles. But knowing how difficult it's gonna be to find the leak in my tub (mine is fully encapsulated in foam), I'm gonna give this a shot.

[@VertigoGTI]

Compared to engines, hot tubs are much simpler. Nowhere near as much repeated thermal expansion, wear, vibration, load, or chemical variation.

[@AshGreen359]

Softub?

[@jerryjones2215]

@@AshGreen359 no, its a hard tub

[@matthewbjork5721]

Did it work?

[@jerryjones2215]

@@matthewbjork5721 no, unfortunately it didn't. It slowed it for about 3 or 4 weeks, but then it gradually went back to leaking as bad as before. I guess if you had a VERY small leak then it might seal, but it didn't work for me. Mine isn't what I would consider a "huge" leak, but it drips about one drop per second.

[@dhrider101]

Great video, also which hot tub is this. I just bought one almost identical and have no idea the brand or model as there are no identifying labels on it.

[@martech360]

I used it last Nov & it lasted until March before it started leaking again. My tub has a couple very large leaks I cant get at so it required 16oz.

[@etamommy]

awesome tutorial! Thank you!

[@mathsupportservices3929]

I bought the product but I have a few questions: How do I run the spa without starting the jets? How long do you run it? Thank you in advance.

[@elainelloyd1]

Thank you! Will give it a go! 🤞

[@Mainecoon454]

Did the repair hold long term.

[@PhamTracy]

Awesome! Thanks for sharing!

[@mrtogoodc]

Do you have a video of you draining n re cleaning

[@robertsherman8269]

?????? did it last like for a year or longer

[@jmcfadden002]

When you say “run” are you talking about the jet pump or just the circulation pump?

[@ScottJoly]

You come back the next morning and say "wow look, it didn't leak a bit, this stuff really works" but somehow your filters got reinstalled after removing them, suspicious that this isn't real and it's just to push product.

[@Bachelor_Gabe]

I just bought a brand new hot tub and have a leak....... do you think I should just use a bottle of this stuff or let their technicians come out and fix it under warranty?

[@thecuss6817]

Warranty

[@reneeroesler3839]

Hi, how long did this fix the leak? I am just wondering if it is a temporary fix that will eventually require actually finding the specific leak/s.

[@brandonslater2987]

when did you out the filters back in?

[@Milestoneswithmay]

So your voice got cut off, so u was saying you ran the pumps for 5 hours? Thanks

[@jaypattetson9443]

I thought the filters were already removed.

[@donprosser7039]

Same issue here although ours is indoors. BTW, when he tub “leaks,” where is the water going to? The ground? The drain? Worried as ours is indoors.

[@robertball3578]

It just leaks out on the floor unless the indoor area was purpose built to house a spa and has a floor drain.

[@olinney]

I did it. It appears it has stopped the leak from happening but now my spa will not turn on & is flashing a number. No Jets work. Please advise

[@reeceg6058]

I used the Lochlor leak sealer. Hopefully a good result tomorrow. I don’t think your supposed to use the whole bottle? It should be apportioned based on guides on the back of the bottle

[@bearacuda3338]

Thanks for the video, do I need to dump the water after the fixaleak?

[@st-qp4mr]

You can....yes probably a good Idea. You might read the directions on the bottle and see what is suggested.

[@Milestoneswithmay]

Hi so now that it is fix, do I empty this water and leave my tub empty for a couple of days, or cab I fill it back up to use right away? Thanks

[@st-qp4mr]

I just left my water in and then slowly filtered the spa sealant out over the next couple of days...I would check the directions on their web site abt that first

[@davidharrison3644]

Damm he should spray those filters out.

[@marylyon3131]

Did. You put. The whole bottle in???

[@jerbear2199]

Black widow! He got lucky pulling the filter out. Widow was under the water alive lol

[@jaythompson8167]

Where’s the link to order

[@pland99]

⬆⬆⬆⬆⬆⬆⬆⬆⬆⬆⬆⬆⬆⬆⬆⬆⬆⬆

[@pland99]

Look up,WOW⬆⬆⬆⬆⬆⬆⬆⬆⬆⬆

[@rudarbusa3314]

@@pland99

[@georgiecatalano90]

Did you have to charge water after you used the treatment?

[@st-qp4mr]

I did because I was afraid of clogging my pump or filter

[@davidsheward2113]

Yes & the other thing everybody is missing is draining the tub to allow the product to cure. Read the instructions on their website because this video is very missleading!

[@RoseFrey]

Like I said you need to clean your filters, with blocked water flow, your pump and gaskets will fail

[@csd915]

Those are some dirty filters. You should clean them. Replace them if it doesn't come clean

[@8356-4]

Your jets look just like mine. Where did you get replacements?

[@st-qp4mr]

www.spadepot.com/

[@8356-4]

@@st-qp4mr Thank you!

[@suealexcallender3484]

When you added the fix a leak you removed the filters. Why were the filter back in when you check the tub the next morning? Does the instruction say it's ok to install filters after the fix a leak has run in the tub for some time?

[@st-qp4mr]

I was worried ..leafs or so.ething was going to hurt my heater and motor ..but they say not to do this ...probly shouldn't have done that but it worked..follow the instructions on the bottle for best chance

[@martech360]

No, the filters are not supposed to go back in until the leak is stopped. You also need to run the pump on high at least every 4 hours for a full day but I recommend every 2-4 hours. I also use a large car wash brush to aggressively mix the water with pump running. my leaks are big & it worked.

[@VertigoGTI]

Great video! Couple of questions, though... 1.) Did you use the whole 8oz? 2.) Did you apply it to the skimmer and the additional inlet for the jets, or just the skimmer? 3.) How long did you leave it in the tub? 4.) How did you remove the excess Fix-A-Leak? On the bottle, the directions say to vacuum to backwash or waste... not sure how that applies to a hot tub... or at least MY hot tub. 🤣

[@st-qp4mr]

@@VertigoGTI yes I used the whole bottle..but I'd read the directions on the bottle if I were u and see what they say to do..I added it to the skimmer and take the filters out..I left it in 24hrs again use the time the instructions give..when I was done I put the filters back in and filtered it out over time

[@VertigoGTI]

@@st-qp4mr Thanks for the reply! I was planning on changing the water around Thanksgiving, but I may just drain it after I do this treatment.

[@snaponjoe]

The filters are their to protect the pump, think about this. A hose inside is leaking you put in a chemical that is going fill that leak. What is that unfiltered chemical doing to your pump?

[@1204timyr]

The pump is strong enough not get stuck with it, while the filters will get permanently clogged with this

[@snaponjoe]

@@1204timyr you can’t change physics. If that pump has to work harder due to a restriction in flow that will cause air bubbles when those air bubbles form it is like little bombs going off which will lead to pump failure

[@MLM111]

It’s made for the spa

[@wpatters1229]

I used this a few years ago and eventually, the circulation pump stopped working and the impeller was full of white stuff which was the product that eventually got stuck into the impeller. I just got a new pump as that one is not that expensive. The one that drives the jets is another story but no problems with it. Probably because it is a much stronger pump.

[@JeffGuidice]

Thanks for the video! Just fixed 2 leaks with this solution. I removed my filter during the process but it looks like I'm now getting a "FLO" error which most likely means that my pressure switch is now clogged. This error prevents the heater from turning on. Have you ever had to replace the pressure switch after using fixaleak?

[@merrilyg]

An Artesian spa! I have one too. My seats are different. Have you had to replace the pumps? I’ve done all 5 of mine. My repair man is a frequent visitor because mine is 11 years old. I haven’t been able to replace my lighting control. The manufacturer in Nevada is an asshole. I also have not replaced my jet spouts, half are gone. Either way, I love my ‘Cadillac of Spas’! Cheers!

[@mrtogoodc]

I have the same one as u

[@Milestoneswithmay]

Hi when you ran your pumps for a few hours, did you leave your filters floating in the hottub, so they didn't dry out?

[@AshGreen359]

You probably don't want that stuff in your filters

[@danielle22226]

It’s ok if the filters dry out

[@ericmorales9565]

How long did you run the pump for after you added the stuff?

[@st-qp4mr]

www.askalanaquestion.com/pool_leak_problem.htm here are the complete directions

[@everythingin.401]

Just be about your business. Plan to save up up and hire a professional spa repair man when you’re planning to use “Fix-a-leak” Just like vehicle’s radiator “Stop-Leak” it isn’t an idea I promote being a spa repair tech. More problems than happiness

[@texasbigdogify]

People! You seriously think this will work? SMH.

[@Jim_the_jim]

It does

[@RoseFrey]

Think you need a clean filter, hope that sealer doesn't seal your filter and totally block the flow of water to your pump. A spa has more water force than anything in your house, would you fix a leak in your home plumbing with something in a bottle 😂😂