Installing a peep hole viewer in your door is a simple DIY project that can add loads of safety and security to your home.
Пікірлер: 58
@jf3180 Жыл бұрын
I want the confidence of someone who does such a bad job of a simple task like installing a door viewer and still uploads a video of it to KZbin.
@Johnnylmilla8 ай бұрын
😂😂😂
@nehemiahjandroep45689 жыл бұрын
How can they put this video up when they Trashed and splintered the hole. The narrator even warned not to do this yet they presented this in the video.. Looks like total crap job!
@solarsynapse2 жыл бұрын
Looks like most people do this. If the door is metal, you really should have a bit for thin sheet metal. A twist bit does not work well.
@0110rroberts11 жыл бұрын
the reason it looks so crappy is because they used too large of a bit, if you want to error on the safe side use a bit slightly smaller than the packaging recommends you can always use a bigger one but you can't undo it after you've already drilled a hole that's too large. plus when drilling keep the drill moving when you back out as well as drilling in this will prevent a rough edge around the hole you've just made. also use caulk during application to prevent air and moisture from leaking in.
@77hemi2 жыл бұрын
Did you not see the silicone at the beginning?
@eetoved1758 Жыл бұрын
Such great advice. Thank you!!!
@dannygalv Жыл бұрын
Thank you
@MrRacky997 жыл бұрын
Perfect Video on how NOT to do it. thanks! 👍🏼😉
@Bennjammin4 жыл бұрын
I watched the video and I the end thought: That can't be right, I'm going to check the comments
@cassandrax15123 жыл бұрын
Welp, that's 72 seconds I'll never get back.
@heywoodjablowme85887 жыл бұрын
LOL! Jacked-up install of peephole for blind people who won't notice the damage you just did to their door.
@DukeCannon10 ай бұрын
I followed your instructions, but mine isnt all jacked up looking like yours. What did I do wrong?!?!?
@Ytsucs Жыл бұрын
You left out the part where you drill a hole at the top of the door and fill the door with water so the peephole can expand and fill the 1st hole.
@42Catnaps6 жыл бұрын
Wow, not only did the job look like crap after, the hole drilled was too large, plus you also showed silicone in the tools needed and didn't use it on the door??
@ginakerry2588 Жыл бұрын
Nevertheless, I think there is a way to do this video in under 2 minutes and hit the proper points I just haven't seen it yet.
@martinhernandez16912 жыл бұрын
What size of drill bit should I use so it doesn't look like this ?
@user-tu2yz1bm1s Жыл бұрын
Basically take their instructions and throw them out ;)
@elizabethfinn5987 ай бұрын
Use the manufacturer recommendation
@SanJacinto239 жыл бұрын
That's a terrible hole! They're using the wrong kind of drill bit, that's why. You should use a hold saw with guide bit for this...
@davisgrier51629 жыл бұрын
+James Merolla would a spade bit work just as well?
@theamerican46093 жыл бұрын
@@davisgrier5162 Spade may work but never as clean as a hole saw. One of the doors was metal.
@xex2kok2 жыл бұрын
@@theamerican4609 The thing is if you look for what the recommended bit is they say to use a regular bit on anything but a wood door and to use a spade bit on a wood door. This is all over, not from this video.
@AimForTheBushes90812 жыл бұрын
lol, what a half-ass installation. Oh well, it helped somewhat anyway.
@GulfCoastRuss5 жыл бұрын
don't cut your eye on the raw metal !
@solarsynapse2 жыл бұрын
Use a bit for sheet metal on metal doors.
@eetoved1758 Жыл бұрын
Thanks! Wondered about this.
@wayneguy6043 Жыл бұрын
Wow, destroyed the door
@janegilbert53042 жыл бұрын
On this video the finish looks terrible. The door is chipped and nothing to hide that.
@user-tu2yz1bm1s Жыл бұрын
Technically you could probably find some type of washer to go under both sides, up against the door. But with the way they drilled it, the washer wouldn't sit flush.
@kevinzhu240114 күн бұрын
Hahaha at first I thought this can’t be right. The comments are hilarious
@rorydale77711 ай бұрын
Fill the hole with putty and reshoot this using a sawzall instead. Don’t wait for the putty to dry, just give it the beans.
@kellyvcraig10 ай бұрын
[snort]
@tnickknight3 жыл бұрын
HAHAHA, so bad it is funny!!!!
@porkchop30708 ай бұрын
Not everyone in this world is as rude as most of these people that commented. ❤️ May God bless you and your family. Thank you for this video! ❤️✝️🙏
@KT-ym1cn Жыл бұрын
Rough install
@colleenwaugh57073 жыл бұрын
Who can fit a spy hole in door
@jarnezp Жыл бұрын
😐 Now that was terrible. The hole was too big and it looks messy.
@videoric3 жыл бұрын
That looks horrible.
@newhampshirejoe59754 жыл бұрын
That hole is way to big
@leilahodo45492 жыл бұрын
Nice awesome look
@Bapuji422 жыл бұрын
lol it looks terrible. git er done!
@powerofknowledge77712 жыл бұрын
That looks like ish! lol . If you're going to rig it, at least say this is the rigged way to do it. lol.
@johnjohnson56144 жыл бұрын
Crap job. Wrong information. Hole saw for wooden doors, step bit for metal door exterior followed by drilling out the inside as appropriate. Put wide tape over the drill point to avoid splintering. It's incredible that they leave this posted!
@anthonychase4945 Жыл бұрын
Very sloppy install.
@bosox65542 жыл бұрын
Very sloppy finish.
@user-ex5jr5to6q10 ай бұрын
OMG... Fail. 😝😝
@akinplus14 ай бұрын
Nasty finish!!👎👎
@Choom2077 Жыл бұрын
🤣🤣🤣🤣🤣
@candyjosimpson10772 жыл бұрын
This is a terrible video the 2nd bit is way to big , if you did this hide your face . You would be replacing my entire door had I paid for your service.
@eliazarvalentine76903 жыл бұрын
See this is a perfect video straight to the point none of that BS talking