Hoverboard motherboard hack how to hack Hover board motherboard Firmware STM32 BLDC motor cart STM

hover-board motherboard firmware procedure how to make a hoverboard cart with BLDC Motor
Please subscribe
Thanks
soon on github my own library
github.com/robot78p/hoverboar...
hacking hoverboard wii
hoverboard use as your trolly cart
how to use Stm8 link utility
hoverboard speed control by Potentiometer meter
make your own control control your robot
you can get the hoverboard firmware
github.com/p-h-a-i-l/hoverboa...
stm8 V2 link bldc motor firmware hoverboard .otherboard
my an other experiment you will enjoy 😉
• pic and place learnin...
hover board firmware
hoverboard trolley
remote controlled hover board
problem solved for stm32 not found
I make it very easy and each step is very clear even for beginners please subscribe my channel not hidden part
ST Link V2 solution
stm32 programing
stm8 programing
ST Link V2 Firmware problem Solved
Hoverboard Steering
Hoverboard Speed control
please check other video Arduino crane experment thanks enjoy 😉
• pic and place learnin...

[@bluecavemen]

What is the point of the firmware? Why can a receiver just tell the circuit board to go forward and backwards?

[@chitibusu]

Do you think we can use the motor controllers already existing on the hoverboard board? To bypass the hoverboard uC brain? Thanks.

[@Fatpumpumlovah2]

2X tilt sensors for each side can be mounted on top of eachother, cables lengthened and can be mounted anywhere on the Trike/Kart on a pivot and angle can be changed via regular throttle cable to tilt forward.... break cable can make tilt backwards for breaking or reverse... then no hacking will be needed to the board.

[@evaldaskum6086]

Hey i want to ask you i did with remote but wheels always spinning when i turn on remote control but dont do enything only on what could be the problem? Pss: i have to remove and insert again battery to stop it and turn off remote. Thanks if you could help 😊

[@mustafacan3.4]

hello bro i need your help on hoverboard can you give me a contact address please

[@user-nb2zp1qx5x]

Sir ji min pakistan sy hun ap ki awaz sy lag raha hy ap pakistani ho help me sir

[@user-nb2zp1qx5x]

Bhai jan ap pakistani ho

[@pathfinder2reality]

Can a hoverboard that was using 14 cell, 24V battery use 20 cell, 36V battery?

[@mharoon5741]

Hi

[@muhammet6152]

I have a controller using 72v 45a stm32 i want to increase its speed how can i do it

[@muhammadahsannaveed6606]

I have an issue while connecting ,though my St link upgrades but when my ST link upgrade ends , it says " ST link device lost when exiting upgrade mode "

[@sayedme2uc]

Can you advise. I am using stm32 cube programmer and st link V2 and upgraded the firmware connected, disconnected st link however, couldent connect

[@MonaLuso]

Hi

[@dannydelacruz5309]

hey thanks for your video. how can I downlod d

[@taiwancowbei8857]

Hi, just curious I have a different kind of hoverboard that comes with two motherboard for each wheel instead of one single big one like yours. Will I be able to do the same step as what you did or I will need to find new firmware for these different motherboards? thank you in advance!

[@alfankosh1]

i really need help i have 2 st-link v2 wen i connected to pc the pc foundet without problem but the STM32CubeProgrammer and STM32 ST-LINK Utility didnot found the st-link v2 what ido?????

[@lorobal]

Hello friend, I would like to know what I have to modify in the file to remove the speed limit

[@ThePhannhung]

Hello Thank you very much for the video, I am Vietnamese and would like to learn to repair balance bikes.I don't know if you can help me to repair the electric balance car circuit?

[@ecoegg4608]

what type of potentiometer you use. what value? ,Thanks

[@Home_made_ch]

Is possible to connect rc receiver instead of potentiometers?