How Do Traffic Light Sensors Work? | Did the lights fail?

In this video, we look at a situation that developed when my viewer was leaving a car park behind a police vehicle. Were these lights broken, or were there things that the motorists could've done to help the lights change?
Join this channel to get access to ADI Training Content
/ @ashley_neal
Dash Camera Affiliate Links. NOW USE CODE 'ASHLEY'
Car - Viofo - viofouk.co.uk/...
Motorcycle - Innov - innovv.co.uk/a...
Motorcycle, Bicycle and Equestrian - Techalogic - techalogic.co....
Social Media
www.ashleyneal...
/ ashleynealdrivinginstr...
[e-mail]
Amazon Links
Sony a6400 Camera - amzn.to/2xVCrn0
Sony A7C Camera - amzn.to/3JUvUIa
Tascam DR-10L Microphone - amzn.to/3M8P0fd
Sony FDR X3000 Action Camera - amzn.to/2YVoPDh

[@deetee5861]

The policeman was very good to not just jump the lights and to attempt to sort the issue. Then, by getting community support officers involved and moving his car too. Props to that officer for not being selfish! ❤

[@butikimbo9595]

Shelfishness sould not be part of police dictionary. If so it should be reported as such. Here in this case with dashcam evidence that, could be a matter do it or not and officers acted by the members of the public side, what is also good to share at least to also show the positive and expected actions from our Police Officers.

[@kdmq]

If the police car had flipped on the emergency lights and jumped the lights, it might have actually caused the light to turn green. Especially considering that the cammer would have pulled forward a few feet.

[@steffenscheibler5849]

I worked for a company supplying road-telemetry and traffic management systems systems (global supplier, also to the UK). There are many different types of sensors but the UK predominantly uses motion detectors on small junctions such as this one because they are very cost-effective and work (mostly) rather well for those types of junctions. Larger or more complex junctions typically have better systems which will trigger on more than just motion and often also combine magnetic loops in the tarmac to detect if a vehicle is standing at the line (which is why you always should drive up to the line, not stop ~5 meters before it!).

[@andyalder7910]

There is an induction loop on this set but it's between the two cars, clearly visible on StreetView.

[@Ep1cure]

Your knowledge is very much appreciated, but the reason I prefer a gap is that I can shuffle to help through emergency vehicles. I normally stop about when I no longer see the line approaching slow, which I know is a before the line (about 3 metres). I haven't had issues with the sensor, but if so, might consider going forward then, maybe nudging to the left a bit (UK traffic from driving on the left, meaning opposite plan if I were from right hand road systems).

[@TestGearJunkie.]

Showing my age here, but I remember the old pneumatic rubber strips sunk into the road. You could get out and go and jump up and down on them..!

[@prekatori]

@@andyalder7910 (51.285841, -2.482382 - if anyone wants to check) I think the dashcams engine should be on top of the loop. The road markings changed between street view in 2016 and this video, but you can see that the loop is pointing away from that white spot on the pavement at 45°.

[@khalidacosta7133]

Siemens? Dynniq? Go on spill the beans then! lol It's often why I end up straddling both lanes when the road is quiet... to get the lights to change quicker at the junction ahead... I am not drunk.. I swear!!

[@davidhaslam1056]

Hands up if you would of simply reversed a few feet and moved forward to see if that worked. 🙋‍♂️

[@jimmysandhuSEO]

1000% yes, I done it just yesterday 😂

[@EZ-D-FIANT]

Yea I've also done it in the past....👍👌👍

[@grahambiggs2017]

Or the car behind could have moved forward. Or you could wave your hand in front of the sensor on top of left-hand traffic light. I wonder why so much crime goes unsolved in this country. 🤔

[@lariwoo]

Can't reverse in a one way system unless you are parking though?

[@EZ-D-FIANT]

@@lariwoo If your gonna be pedantic I will too, you sure that car Park exit qualifies as road....

[@SGz_Eliminated]

I think Ashley was spot on, the traffic just doesn't move after its cycled back to red. The chances of the sensors breaking at that exact moment is extremely slim.

[@Djnffnoeosmfasjjd]

This is not a red light camera.

[@tarnmonath]

@@Djnffnoeosmfasjjd No-one said it was.

[@markhorton8578]

The default fail would be red, for safety purposes.

[@JB9000x]

It is probably a Microwave Vehicle Detector which works on doppler reflection

[@JB9000x]

​@markhorton8578 if it stays red for long enough it will suspect a fault and revert to forced stage demand

[@antm2296]

This happened a few months ago with temporary traffic lights for construction work, the lights were situated at a blind bend, I had a copper behind me along with around 20 cars. After 8 minutes on red and no change or other traffic oncoming, I started to creep forward and went straight through with all the cars following, long behold they were manually put onto red purposefully as when we got around the corner there was a construction HGV blocking the road and using its crane to drop off materials. So we all put our tails between our legs and reversed like proper idiots 😂

[@kiradotee]

That is stupid from the workers. They should have sent someone with high viz to be next to the red light. Ideally with a stop sign. If the temporary light is red for like 5 minutes people will jump them, they'll assume they're broken which is fair.

[@ianl1052]

​@@kiradotee It would have been safer for all of you to stay where you were, as so many people had committed to this maneuver, until the lorry had finished its dump and then carry on. While everyone was waiting, the police officer could have got out and informed everyone behind the lights of the issue and tell them not to follow.

[@annabelholland]

In that case, the road should have either been closed or have an authorized personnel (traffic management officer, police, Highways England) stop traffic and give reasons why. Remember that having traffic stopped longer than 60 seconds without reason may cause impatience

[@kinkaito5433]

@@ianl1052 With so much roadworks in the UK people will only wait so long, as alot of the time, traffic lights are either not set up correctly, or are broken, people aren't going to wait for a end-less amount of time, if the road was "Closed" for that long, There should be a Road closed sign, or a person to direct traffic/and explain whats taking so long, People will not, and should not, have to wait and Pray the lights are working,

[@kinkaito5433]

@@annabelholland Cannot agree more.

[@craigstevenson6565]

I'm just dropping a wee message to say thank you. I just passed my test, first time one minor with my dad as my only instructor. Your videos helped me in many situations!!!

[@ashley_neal]

Great job! Congratulations!!

[@CraigNiel]

I've been in this exact situation (without the Police though) where the red light just stayed on and would not change. I tried reversing and driving forward but nothing happened. After about 5 minutes I just had to go through the light as it seemed broken. I just treated it like any other junction and gave way to any traffic as you normally would. Luckily it was quite quiet and I just took it really slow and all was well. It's so ingrained in us not to go through a red light (and rightly so) that it really does feel so strange to do it, even under such necessary circumstances.

[@klausbinn777]

More accurately, it's ingrained in MOST of us. 🙂

[@CraigNiel]

@@klausbinn777 haha yeah that's true!

[@InviolateTree]

In that seituration you can go thorught a red as you have a good reason to cut the red then only time you can't do this is if there a cameras

[@stevezodiac491]

​@@klausbinn777yes, there are a lot of car and particularly taxi drivers who drive through red lights.

[@Peer_Review]

Something I found really interesting going to the US is that apparently you’re allowed to turn right through a red traffic light (equivalent to a left turn here in the uk) when at a junction, basically treating it as a stop sign. It felt super wrong every time

[@pauleff3312]

AS A CYCLIST - I *hate* jumping red lights.... But if they don't know I'm there because I'm not big enough / heavy enough / wide enough to "trip" the sensors, and it's 1 AM or so and there is absolutely no-one about WHAT DO YOU EXPECT ME TO DO? Sit there and freeze to death? I always, always stop for red lights but I won't wait longer than 20 seconds where and when the roads really are deserted. I listen, listen, listen and then set off again - usually cussing whilst doing so into the video camera about the traffic lights needing to work for me too!!!! I HATE jumping the lights and would just prefer that they work!

[@PedroConejo1939]

At least the Highway Code (checks notes) allows you to make a judgement call if you have good reason to believe the lights have stopped working: "If the traffic lights are not working, treat the situation as you would an unmarked junction and proceed with great care." - Rule 176. Given the dashcam evidence, if there was no possibility of trying to reset them by reversing, I'd follow the advice given. Another reason to have a dashcam. It is a good reason for auto-cycling the lights every few minutes, but that's for the engineers to implement. I don't listen to the radio these days, but I used to hear 'stuck on red' quite a lot in the traffic updates on my way to work.

[@smilerbob]

100% agree and going through on red would be last resort for me if all other options do not work. As for the traffic reports, I always used to think someone phoned that in as an excuse to jump red lights and if caught refer them back to the traffic reports on local radio. One of many stories I used to make up to help alleviate the dullness of the daily drive to and from work

[@PedroConejo1939]

@@smilerbob That made me chuckle. It was the kind of thing I might do.

[@allanhook]

The highway code says if the lights had stopped working. I would say that this means they are not showing any lights. The lights were working, just not working properly.

[@markwalton8644]

​@@allanhook Not Necessarily. If the computer which controls them freezes then they no longer work as they should, so I don't see why you can't proceed with great care.

[@smilerbob]

@markwalton8644 I think the key phrase is “if the traffic lights are not working” rather than “if the traffic lights are not illuminated” thus covering for all types of failure modes as you describe 👍

[@1988dgs]

Backing away and approaching again would have fixed this. Also on the ground loop system with a motorbike stopping and starting again gives the system a bigger jolt

[@DaveHines1]

As a motorcyclist , I’ve often found traffic lights don’t pick up my motorbike , and have to wait several minutes til they cycle . I recently got stopped for about 5 minutes at temporary traffic lights which kept on letting cars thru periodically from the other direction , they eventually changed to green when a police motorcyclist approached the lights passing the stop here sign .

[@RichardBeds]

As a cyclist I often find that traffic lights don’t trigger. I wonder whether it’s because I’m not a big enough object to trigger them? I also find that some traffic lights with induction loops don’t work in the rain.

[@clickrick]

@@RichardBeds Big enough, heavy enough, contain enough metal ... all of those things, depending on the precise sensors.

[@insoft_uk]

As a cyclist they don’t pick up cyclists and have no option to just ignore and continue through if safe t do so, so much for Highway Code telling cyclists to stop at reds as in some situations we be waiting for hours One set I know that’s like this and learned to just ignore them.

[@andrewnorris5415]

Same on a cycle. My tips that I found work are - 1) temp lights, usually a small extra LED red light comes on when it has picked you up. Move about a bit or go closer, these are motion sensor based. 2) look out for the sensor tracks in the road. When your front wheel goes over it, push down very hard on the wheel at low speed. This nearly always works on lights that would otherwise not pick me up.

[@C0baltBlueJ]

I had this on my motorbike a few years ago. I must have waited a good 5 minutes with zero traffic in any direction before I decided to *carefully* pull out on the red. I assumed it was because it was dark and it hadn't seen me, even though I had my lights on.

[@learigg]

The lights in Ayrshire are mostly controlled by induction loops buried in the road. A common issue is cars turning right not pulling forward on green light. There is a loop in the road where you wait to turn right, if you're not on top of this then the filter light will never activate. I've sat through 4 or 5 light sequences when the driver in front refuses to pull forward. We could definitely use some general training on how lights work and also reinforce thats its ok to pull forward when right exit is busy, assuming we're not on box junction.

[@alex291190]

Sainsburys in Prestwick is bloody awful for that.

[@Kromaatikse]

This junction has both motion and inductive sensors. You can see the grooves for the latter pass under where the camera car stops the first time (diagonal, third car back) and also, crucially, *between* where the police car stops (halfway across the stop line) and where the camera car stops. This latter set of grooves go straight across the road, and are most easily seen where they interrupt the double-yellow painted lines. I think the lights changed for the first time, not because there was a gap in the traffic, but because it sensed at least three cars waiting (both the first-car and third-car sensors active). Then it was confused, not by a lack of movement per se, but because the remaining cars stopped in positions where the installed sensors couldn't detect them. If the police car had reversed back so that it covered the first-car sensor, this would have prompted the lights to insert this road into the normal cycle sequence; the third-car sensor allows for a priority system, and I think the motion sensor is mostly used to judge when to revert to red.

[@thedave7760]

Or if our driver had just pulled forward to the police car just a little it would probably have sensed something.

[@RoamingAdhocrat]

Reversing back off a junction towards queueing traffic with pedestrians crossing is dangerous. Police driver had already crossed the stop line - after that point he should've ignored the lights and proceeded over the junction cautiously at his own discretion (same as any other motorist). Instead he got two colleagues to make a bit of a meal of things!

[@spac20]

Perfectly said 💯👌🏽

[@robhunt8682]

I cannot see any grooves in the road. I think what you are seeing is the reflection from the windscreen of the air vents. I thought they were sensors in the road at first but if you look carefully they are actually the vents' reflection

[@Kromaatikse]

@@robhunt8682 There are diagonal grooves visible just before the camera car stops for the first time, and it stops directly over them. This is the "third car waiting" sensor. The grooves for the "first car waiting" sensor are not easily visible on the road itself, but there are corresponding "cuts" in the double yellow lines which are easier to see. This sensor falls between the two cars when they stop for the second time, but is also out of view while stationary. These two inductive sensors are used in conjunction with the one on top of the lights, which is motion sensitive (so can detect approaching or flowing traffic) but cannot detect a stationary vehicle.

[@ShedTV]

I agree with the theory that the sensor isn't being triggered. I think it's pointing at the bit of road between the Police car and your viewer. The Police driver got caught out as the lights changed quite quickly, because they're probably timed in favour of the main road. He couldn't clear the junction, leaving him stranded across the line. The other car is too far back to catch the sensor. I'm pretty sure if the Police officer had reversed up to the camera car it would have triggered the lights.

[@andyalder7910]

There is an induction loop in the road but it's between the two cars, clearly visible on Streetview.

[@ShedTV]

@@andyalder7910 Thanks, I just had a look. I wonder if the sensor on the top of the lights is there to detect cyclists who might not trigger the loop. Even with the entire Somerset constabulary wandering around nobody walks in between the two cars!

[@johnlochness]

One thing I've noticed with temporary traffic lights in recent years is that if the road is quiet they will turn to red for both directions, then when a car approaches they can instantly turn green for that direction.

[@Lysimachus]

This happened to me on my first ever day of driving on my own... I decided to just proceed anyway after five minutes of waiting and on the other end luckily all incoming traffic had come to a stop.

[@joefarr3304]

Often with temporary lights if you flash your high beam at them they will have changed by the time you get there. I was always told it was so they could detect emergency services vehicles with their flashing high-beam lights.

[@dr_dr]

Was the buried induction loop between the cammer and the Police car? It looked like it, in which case the Police cars poor positioning over the white line meant the system couldn't "see" it, and the car behind hadn't come forward enough to trigger it either.

[@clickrick]

My late father worked in traffic management until he retired some 25+ years ago. There are many variants of traffic light control, with sensors visible above (as here) and buried in the road (as you said), with time of day also a factor, but most have a default "error" mode that they will fall back to if they fail to sense anything for a set period of time. As with everything, that period can vary, with times of 15 minutes not being uncommon in a city. In other words, if it doesn't sense traffic approaching for 15 minutes, the controller will assume there's a fault with the sensors and go to standard timed intervals. Whether it then goes back to sensor-driven is another variable, but you might see a small red light visible on the equipment somewhere which will indicate that it's in this error state.

[@pugsterjosh7925]

Does the UK have anything similar to the US, whereby an engineer can initiate a “flash” state for the whole junction where all the lights will flash amber?

[@clickrick]

@@pugsterjosh7925 Flashing amber in particular is used in the UK at pedestrian light controlled crossings to indicate "proceed with caution". It follows the red phase. I don't believe there's anything equivalent to what you say, though. Not that we couldn't, and the same "proceed with caution" message would be entirely applicable, but I think the traffic engineers have long since learned that the driving public cannot be trusted to exercise "caution". Ever.

[@grahambullman]

These lights are 400 yds away from my house, and this happens a lot with them. They don’t recognise me when I’m on my bike. Normally two lanes of traffic line up, depending which lane is required around the bend which I think helps to keep things flowing and ensure there is generally some movement. 🙂

[@andyalder7910]

Sit on top of the induction loop just behind the turn right arrow; on a motorbike have your engine over the loop, on a push bike try the front wheel over the loop and keep turning the handlebars so the metal wheel makes the induced current fluctuate. You can clearly see where the loop is cut into the tarmac, if you are in front of this you won't trigger the lights so move aside and wave a car forwards over the sensor. You can also ask the council to adjust the sensitivity.

[@andrewnorris5415]

My tips that I found work are - 1) temp lights, usually a small extra LED red light comes on when it has picked you up. Move about a bit or go closer, these are motion sensor based. 2) look out for the sensor tracks in the road. When your front wheel goes over it, push down very hard on the wheel at low speed. This nearly always works on lights that would otherwise not pick me up.

[@davidkane4652]

Im very sorry you have to live in Midsomer Norton

[@grahambullman]

@@davidkane4652 I'm not. Pubs, supermarket, post office and restaurants all within 5 minutes walk of home, and greenway cycle track on my doorstep.

[@captafrica]

Oddly enough, I had exactly this situation a few months ago, in a major city at night trying to join from a two lane, one way side road to a main road. I waited at the lights for around 6 minutes in the left lane, realised something wasn't right when private hires blew through the lights while the rest of us waited. Once a gap in the traffic developed, I proceeded through the lights treating it as an unmarked junction (As Rule 176 in the Highway Code states). Bad luck for me that an undercover police car had joined the queue around 30s before this and pulled me over once I'd passed the junction. 3 points and a fine with a solicitor advising me not to fight the FPN as technically there is no official guidance on how long a light needs to be out before we can consider it broken, and losing the fight in court could result in a much larger fine and a charge for driving without due care and attention. I tried explaining to the officer that pulled me over that the light clearly was not working and I had several minutes of evidence of this on my dashcam. He wasn't interested and "kindly" let me know that I don't have the authority to determine that a light is broken and that I should wait at the red light for as long as it takes.

[@russell5791]

Rule 176 of the highway code Only go forward when the traffic lights are green if there is room for you to clear the junction safely or you are taking up a position to turn right. If the traffic lights are not working, treat the situation as you would an unmarked junction and proceed with great care. - It does not say who or what is defined as a traffic light not working, neither does it give guidance on how long you should wait before determining the traffic lights are not working. It also does not define whether a light stuck on red is a traffic light not working. It does not say that you can't define when the lights are not working, in fact the highway code is suggesting you decide. Vague at best, probably worth fighting in court. (I woiuld have)

[@mda5003]

Difficult without police being there but I've always assumed that after waiting around 4 minutes the lights must be stuck and to proceed with caution always remembering that in the event of an accident/collision you would be at fault for crossing a red light. However, I would be concerned though if there was a possibility of there being a red-light camera in operation.

[@pocky1scot1]

You would only be at fault for not being safe not because of the broken red light. Rule 176 "if the traffic light is not working, treat the situation as you would an unmarked junction and proceed with great care"

[@kenbrown2808]

I have no experience with UK red light cameras, but my understanding of how US red light cameras work, is that the trigger for the camera is defeated if a car stops at the stop line and then proceeds through the junction. of course, this should not be taken as instruction on how to run red lights.

[@mda5003]

@@kenbrown2808 I've never heard of how that would defeat a red-light camera in the UK simply by stopping and then moving off. The cameras we have can even see what you've had for breakfast!

[@kenbrown2808]

@@mda5003 it's why I clarified that I have no knowledge of the logic UK red light cameras work on. in the US, a red light camera will see a car approaching a red light, and wake up, and watch for it to cross the line. if the car stops at the line, it says, "aw shucks, it stopped" and then looks for other moving cars. I'm guessing part of that is because in most places, motorists are allowed to make a right turn on red, after stopping, if it is safe to do so. I know we have the rule that the camera must produce photographs of the car approaching the line, and then completely crossing it, before a citation can be issued, though.

[@pugsterjosh7925]

⁠​⁠@@kenbrown2808 I believe in the UK red light cameras utilise the induction loops that are already embedded in the tarmac. If the light is red and the control system registers a temporary change in magnetic field, it must “assume” that a vehicle has ran a red light and snap a picture.

[@lyndsnevircs3745]

I was required to wait at these lights yesterday. Even when we were stationary, the lights changed to green within 2 minutes. I would say they were faulty, they changed red very quickly aswell from my past experience.

[@JaneAustenAteMyCat]

So they work better when you're paper, or perhaps a pen? Interesting 🤔

[@mattwoolford]

Hi, software engineer 👋🏼 I don’t pretend to have worked on traffic light systems but I spend a good chunk of my time observing technologies in our every day (and maybe getting a bit frustrated with the build of some traffic light systems in particular)! TL;DR don’t flash your lights at traffic lights. It does nothing and so you look silly. Sensors you see on top of traffic lights are used to detect MOVING traffic as the video points out. However, the under road sensors (induction loops) detect traffic that has moved over it or is stationary above it. The best traffic lights have under road sensors 200m or so back, which means the traffic lights are green by the time you reach them. The worst traffic lights keep the major road waiting on a red light, and the empty-of-traffic minor road on green. The sensors on top of traffic lights are generally infrared or microwave. For simplicity, let’s just call it radar. Radar can detect stationary or moving objects, but how would it know if it is detecting a stationary car or a rogue pigeon eating someone’s McDonald’s fries? Instead the radar sensors measure speed to solve this, with a prefixed speed to determine a car. A pigeon is unlikely to be consistently moving towards the traffic light above 5mph (birds fly erratically, for example). Induction loops measure, you guessed it, induction, thanks to the metallic build of cars. This can be used as a switch. It doesn’t require constant induction to know that a car is there, if the induction changed over the threshold and then disappeared, this would be a sign that a car has passed over it. Here’s the general basis of the algorithm I’ve observed with some made-up numbers, and some brief research would seem to confirm (please bear in mind every traffic light system is different, but in a general sense the following is likely to apply). A basic set of traffic lights should have a fixed timer for an interchange. For example RED_TIME = 120 //Seconds GREEN_TIME = 30 //Seconds WHILE (TRUE): //Repeat indefinitely WAIT(RED_TIME) CHANGE("GREEN") WAIT(GREEN_TIME) CHANGE("RED") A good traffic light system should build on this by adding vehicle actuation (sensors). A separate process will run: SENSOR.ON("Vehicle Detected", REDUCE_RED_TIME(RED_TIME * 0.1) // Fast forward the red time by 10% of the remaining time to reduce waiting time ) This means that when a sensor detects a vehicle (or vehicles depending on build), that traffic will get prioritised, but in the case the sensor hasn’t detected anything, there will still be an opportunity every 120 seconds for vehicles to pass through which is a failsafe. Most traffic lights will do this. On complex junctions though, there are obviously other considerations such as traffic directions and sequencing.

[@drcl7429]

This is not really how it works in embedded systems.

[@mattwoolford]

@@drcl7429correct by my own admission, but for the sake of concept, this is how it works to the everyday person 😄

[@rogerknight8092]

You need to multiply by 0.9 to get a 10% reduction.

[@mattwoolford]

@@rogerknight8092 not in my example when I’m using it as an argument to a pseudo function “reduce_red_time” as I am reducing the red time by a specified 10%. But yes, that is the calculation for finding 90% of a value in any other circumstance

[@JB9000x]

I did software engineering at university and I've been a traffic engineer for 20 years. 😊

[@johnkeepin7527]

While this is an exit from a public car park, there are some places where the exit only works for buses fitted with traffic signal priority (TSP) kit, which is used to detect them and sets the route for them. Also used to give them priority over certain junctions, in which case the sequencing of routes varies, rather than a standard one.

[@geko7844]

One big issue I see is people not driving right up to the stop line - they often stop about a car-length back. This is a problem for lights with just one magnetic sensor - it doesn’t detect a car there and so the light stays on red for longer (until the lights cycle themselves). Interestingly, I remember an old Kipkay video years ago which recommended putting a strong magnet under your car - especially for small vehicles like mopeds - to make sure you trigger the lights 😅

[@ihateunicorns867]

This happens to me all the time when I'm on my bike. There's this one spot where I always get stuck. If it was just a junction, I'd dismount and wheel my bike through, but it's an alternating one-way system.

[@averyboringusername]

The two principal sensors used on traffic signals are microwave detectors (usually a small box on top of the signal) and inductive loops (wire embedded in the road surface). The microwave detector has a microwave transmitter and the reflected transmission is picked up by the detector. A moving object will create a Doppler shift with the reflected signal. If the detector observes a change in the reflected signal it assumes a vehicle is approaching. Microwave detectors usually have a minimum trigger speed for approaching vehicles to stop false positives. Inductive loops generate an electromagnetic field, a metal object within the field changes the properties of the field which is detected by the field circuitry. A few observations: When a signal is controlled by an induction loop at the traffic light there is sometimes an earlier loop to detect queue length. If a vehicle is waiting at the lights on the induction loop if you stop your car on the earlier loop you can trick the system into thinking the queue is longer than it actually is therefore reducing the time of your red phase. Puffin crossings (pedestrian user-friendly intelligent) have a microwave detector to sense if people are still on the crossing. Impatient drivers who keep creeping forward can sometimes be detected by the crossing occasionally confusing the system into thinking a pedestrian is still crossing therefore making the driver wait for longer. The microwave detectors on temporary signals often have a small led which illuminates when the sensor detects movement, you can watch for that led to make sure the lights have detected you.

[@neiltill]

I think if i had no police assistance and it was safe for me to do so after that long waiting I'd of carefully gone through the red light and hopefully the sensor (if it wasn't broken) was triggered by traffic behind me to get things working again. I do know at work as a bus driver if I had a situation like this, I can report to our control that a set of traffic lights appear to be stuck on red, on said road, and they can report it to the local council.

[@juddy_1997]

Wouldn’t work in Australia we have red light cameras at every intersection

[@neiltill]

@@juddy_1997 you could be sat there a long time in Australia then?

[@juddy_1997]

@@neiltill possibly but this isn’t very common.

[@rondameier8168]

I preface this with I live in the states..... Here I would say almost all have the sensors in the ground, or under the tarmac as you called it... And if you know where that area is, then drive onto it. I have a signal near me that is a left turn off the freeway exit, but the right hand turn is not with it at the same set of lights, it's also on a steep incline and it's a strange kind of left hook if you will. Well it also doesn't like to change if you aren't on the plate under the tarmac, a very specific way. You also can't flash your highbeams at the signal because of the angle they sit at, because a lot of lights here have a sensor on the top of the light as well. So what I learned a long time ago was to reverse back and roll forward again. And to do this as many times as you need, or if traffic allows. Motorcycles here are notorious for not being heavy enough to set the sensor off. And will at times get stuck at the lights till a heavier vehicle pulls up. So with the light near me that does this, I just roll back and forward again, but I've also learned to stop on the sensor in a little bit of a different way, and it seems to work... I also think in some places here that if you've sat at a light for over 3 minutes (don't know what the exact time would be), and if there is no traffic you are allowed to treat it as a 4 way stop, 2 way stop, etc....

[@ianl1052]

Respect to the police officer for staying patient and calling for assistance to cure the problem.

[@NckBrktt]

I have noticed not all traffic lights can detect 2 wheeled vehicles. This can be an issue at quiet times early in the morning. At some lights I sometimes have to wave madly and flash headlamps even though there is absolutely no other traffic coming. Even then sometimes nothing works and I have to "proceed with caution" (usually 6am and deserted). Other times a car or van will approach from behind and rescue me by triggering the lights.

[@thomaselliot2257]

That happened to me over 30 years ago trying to come out of a side street at Paisley Road Toll , Glasgow, to be exact. My traffic lights seemed permantly on red. I waited for about 3 cycles of lights on the main roads . It was early evening , I think , and it WAS quiet, so I emerged against my red light. Of course, there a was a police car from nowhere, and stopped me , but they let me go when I explained. Phew 🙄

[@Eelesy02]

Hi there, I work as a traffic signal engineer. You’re correct in fact that the ‘sensor’ is looking for moving cars which is why it’s stuck on red. It’s called an MVD - Moving vehicle detector. Usually smaller side roads also have a stop line detector whether that’s a physical in road induction ‘loop’ or an above ground sensor/camera. This would detect a car that is waiting at the stop line even if it’s stationary. It looks as if there isn’t one here because usually they have a failsafe and get stuck on rather than off. If you report to your local council they are usually pretty good when it comes to traffic light issues and they might have one installed. Cheers 👍

[@ChrispyNut]

There's a set near me that defaults to red on main road, green on side. Even though you didn't explicitly get me started on it, traffic light irritations always bring my mind to those which are incapable of detecting cyclists.

[@rampak1]

Lights near me default to red on all roads if no traffic is detected for a while. This is great because it means that when you do approach from any direction at a quiet time the lights will immediately go green for you.

[@ChrispyNut]

@@rampak1 That is the more sensible way, until Syke, someone coming from the adjacent at the same time 😆 These lights are just badly set up. I tried to get them changed, but, nope. Most annoying are the trucks that have to (almost) stop, so much wasted fuel and extra pollution. Oh and they also don't detect cyclists. So bad!.

[@Shaun137]

Glad I found this again, Happened outside Asda in Stafford. Someone blocked the exit route on the Box Junction and the lights cycled twice and then got stuck as nothing was moving and the sensors must have decided there was no need to change. The roads in Stafford were chock-o-block again due to an accident on the M6. Decided that when said car had moved out the way to pull forward slowly on Red and when it was safe to proceed off, the car behind followed too. Hopefully that got the lights going again. Box Junctions are there for a reason, no real excuse getting caught on one unless there's exceptional circumstances.

[@blueish4]

you'll sometimes get the ground detection loops on smart junctions with cycle lanes - obviously since bikes are smaller (and sometimes not made up of enough metal) they'll never detect you. in these cases i normally cross the junction with care in the pedestrian phase after pushing the button you can also treat a broken sensor traffic light as a stop sign if and only if its cycled through the same phase twice and ignored you, just be very careful

[@oxonomy2372]

You can try leaning your bike over, works on some

[@andrewnorris5415]

Not heard of these that pic up metal! One of my bikes is full carbon so would have no chance. My tips that I found work are - 1) temp lights, usually a small extra LED red light comes on when it has picked you up. Move about a bit or go closer, these are motion sensor based. 2) look out for the sensor tracks in the road. When your front wheel goes over it, push down very hard on the wheel at low speed. This nearly always works on lights that would otherwise not pick me up.

[@GaudyDragon8963]

Woah, this is my hometown. I dont think these traffic lights have sensors because they are programmed to be in time with the next set of traffic lights, which is just around the corner, and this is to stop causing problems with the traffic

[@QuentinStephens]

One thing this shows is that traffic lights need two sensors: cameras and ground loop, in case one of them fails.

[@em0_tion]

💲👀😂

[@alexanderbabington5270]

I had a similar situation where the traffic light was not changing on my driving test. Observed multiple full cycles where it did change to let traffic out from the opposite road but not mine on a cross roads. I made the decision it had failed told the examiner and said I was going to procede with caution provided there was no traffic. The examiner didn't say much at the time but afterwards said he agreed with my assessment. I passed the test

[@vator_rs]

Hi Ashley, I just wanted to say big thank you for all your videos all the way here from Serbia! This past Monday, I passed my drivers test on 2nd attempt with 5 minors! Your videos have helped me learn a lot about traffic flow and how to deal with certain situations. I will keep watching but now I don't have to stress about passing the test 😂

[@ashley_neal]

Congratulations!

[@vator_rs]

@@ashley_neal Thank you!

[@bryansmith1920]

Thank you Ashley for trying to get out there the knowledge about road sensors, I honestly wonder what motorist think, when they see the geometric pattern in the road surface at a T/L controlled junction, I'm an ex HGV driver also a Qualified driving instructor from back in the 1980's, I feel sad for the lack of knowledge of young drivers

[@StefanVeenstra]

“Smart lights” as they're sometimes called here in NL. Though no mounted sensors, usually just loops in the ground that detect cars and even cyclists approaching or waiting. Do think people shouldn't take these for granted though, I've had seen plenty red light jumpers going for it, because they expected green and didn't bother to slow down. Just because these systems aides traffic flow, we shouldn't give up on paying attention.

[@itIsI988]

Can't stand the ground loop ones. Given how most bikes are aluminium these days it's no wonder why cyclists generally run red lights.

[@ibs5080]

One nice option in North America if traffic lights ever get stuck on red: The fact that it's legal to turn right on a red light over there, with a few caveats to be obeyed. You can also turn left on a red light over there, providing the street you are turning into is one way. Again, a few caveats exist but it's a useful option to have in case of lights stuck on red...or indeed to get out of the way of an emergency vehicle. Oh and over there, red light cameras can distinguish a legal turn on red, as long as you come to a complete stop behind the line first. They even have signs at such intersections to remind you to come to a full stop first.

[@jaycee330]

Unfortunately, in this example it wouldn't work, as the cammer is approaching a right-turn only lane (which in the US would be left-turn), so even if the option to turn left on red was available, it would not help here, as you would have to cross opposing traffic.

[@ibs5080]

When on a relatively free flowing road with multiple traffic lights, I like to have a few vehicles ahead of me in the hope they will trip the sensor for me. I've managed to get quite a long uninterrupted "green wave" using this technique, having the other vehicles do all the work of slowing and then accelerating to the next set of lights. In the meantime, I've been able to maintain a relatively constant speed.

[@frogsplorer]

Cool!

[@PedroConejo1939]

In Nottingham back in the late 70s (I think), there was a green wave on several roads with multiple sets of lights. Stick to the speed limit and you could get through most times. Automatic Grüne Welle is, I believe a German implementation (like many traffic improvements) and I can remember learning about it when I lived there in the 80s. It was far from new, even then; there were even signs telling you the optimum speed.

[@johnnymichael1804]

Atta boy, Ibbadeeb.

[@12crepello]

Upon reading the Highway Code I conclude that as long as you pass the stop line on green then you can proceed even if the lights subsequently change, obviously with care. Do you still have to stop if you are past the stop line?

[@WhiteEagleTube]

There is actually a magnetic sensor on these lights, you can just about see the wire buried below the white arrow. There just wasn't enough of the police car over it.

[@aspuzling]

What is a magnetic sensor exactly? Can it detect the steel frame of a car or something? If that's the case then it shouldn't matter whether the car is stationary or not. But if it is a radar sensor like Ashley is suggesting then it will matter.

[@andyalder7910]

See the induction loop cutout better on StreetView on the exit of Sainsbury's carpark in Midsomer Norton.

[@WhiteEagleTube]

@@aspuzling I think it creates a low magnetic field. So anything with sufficient mass in that area will trigger the sensor. I think they are always paired with a camera as well.

[@garyt123]

Not magnetic at all, but an induction loop as @andyalder7910 has mentioned. They work literally thanks to "mass" of metal.

[@jaycee330]

Agreed. If the police car had reversed back and moved forward again, it would have probably triggered it.

[@mrsulzer66]

Another function of sensor would appear to be speed control. I commute (at night) through a set on a main road which as you state in the video, remain at green until traffic from the junction triggers them. Although, if you approach these lights (on the main route) even 5-10 mph faster than the speed limit, will trigger the lights to go to red regardless of the fact there is No other traffic anywhere.

[@brendanhegarty6792]

The sensors are built into the roads in Australia. Some drivers stop so far forward that I worry they won't trigger the sensor so I drive right up behind them so my car covers the sensor. I can remember years ago being stuck behind a truck waiting to turn out of a shopping centre. He was the first in line but too far back to trigger the sensor. I had to get out of my car and tell him to drive forward or the lights would never have turned.

[@garyt123]

Ashley, they don't actually detect _movement._ They detect the presence of metal. This occurred because the cop car had passed the "loop" buried in the tarmac. If the cop car had reversed about a metre and a half, the lights would have changed. When a vehicle passes over the "loop" or is stopped within the "loop", any reasonable mass of metal induces low voltage eddy currents in the wire loop. This decreases their inductance, and this is what the circuit detects. It is very, very, often, that lights don't change for small capacity motorcycles, which _literally_ don't have enough mass to induce a current in the "loop", so the light stays red. Car park barriers use the same principal - remember that episode of Mr. Bean trying to exit a car park without paying? He thought it was weight, or pressure.....

[@lozyoung4110]

Pet hate - sensors that don't detect me on my bike!

[@stephenhill8790]

With temporary lights often a wave of your hand will work, if it has not changed, the others you need a long branch, but don't stand too close, flashing lights will not work as it's an infrared system, some can use ultra sonic but rare

[@123MondayTuesday]

These traffic lights detect cops and hold them up

[@ashley_neal]

I love your comments 😂

[@Real_Venture_Out]

I worked for a company years ago that used to to use temporary traffic lights for road works, and the sensors on the traffic lights that we used were positioned on the top and wouldn’t detect traffic travelling towards them at less than 5mph. The flashing of headlights is a complete myth, it’s the physical movement that they detect.

[@rickiecheese36]

I agree with some other comments. I worked for a Hire company supplying temporary lights for roadworks. The sensor work by detecting the movement of approaching vehicles. The viewers car should of moved back (if possible) and forwards again to create movement to wake the lights up. They usually have a small red light on the front that flickers to indicate that movement has been detected.

[@StevenGreenGuz]

I once came across the opposite problem. The lights were going green in both directions, I almost got knocked off my bike. A friend and I decided to play traffic cop and directed traffic and tried to explain to drivers what the problem was. Eventually some police officers came along and took over. They just told us to bugger off, no other discussion. I guess a good deed is its own reward.

[@1harryrobert]

The Conflict Monitor prevents this from happening.

[@Rich-CV]

I work in traffic management ( temporary traffic management) includes temporary lights, road closures etc. Usually the sensors are motion sensors especially on temp lights, but I have seen more recently lights set to timings which makes a much longer wait time on RED, if you are driving towards a set of temporary lights the (When red light shows wait here) board is supposed to be 15 metres back if you go by the traffic management Red book, but you soon realise at that distance the lights sometimes struggle to trigger so need to just slowly move forwards and the red light will trigger on the sensor just above the red light.

[@andrewtaylor-x3c]

Hello Neal, you are right the sensor relies on movement passing over the magnetic triggers in the road, motorcycles have this problem when they don,t activate the trigger and holds traffic up behind, provide camera evidence from camera activity and the police/DVLA or the CPS won't action the event.

[@ConquerDriving]

There is a junction near me that suffers from this problem. Reversing and going forwards again seems to solve the problem.

[@IseiNabuka]

Thank you Ash for this, most drivers in my area do not or not aware that most traffic lights nowadays have sensors on them. In a shopping complex where I work, we have to tell drivers who are stuck at a traffic light is that they need to drive up towards the white lines as the sensors cannot detect any vehicle

[@1harryrobert]

Oh dear, lol.

[@chrispayne523]

I seem to remember being told somewhere, might have been during my PSV training that if lights don't change after 5 minutes carefully move through them.

[@megajohntopunishenslave427]

I’m a bus driver in London ATO temp lights are always messing up. Thus there default aspect is red. We are taught that if suspected or not changed for over 5 mins pass the red light under extreme care and caution with hazards on.

[@ironlungthe3rd]

Worked in traffic management in the UK and currently in Australia for many years, the traffic light changing is called 'phasing', this is when a light changes from green then amber to red or vice versa, the grooves cut out and cable layed in are generally referred to as 'loops', they detect any vehicle by electro magnetic interference above the circuit, The sensors that are on the lights themselves are very temperamental, and by the situation at hand definitely means there is a fault with the system, this can occur due to many different things, it may be that the phasing is incorrectly set, or they work off of cars needing to be places with a certain tolerance, unless that is detected it will not trigger the phase.

[@richcolour]

Thanks for highlighting the issue. Too many people here in Edinburgh stop before the magnetic coil sensor, or after it in the bicycle area. I often get out and ask them to move over the sensor. I sent Edinburgh Council a very detailed description of the problem at my local junction. No reply or action taken. Considering putting my own sign up saying "Stop here to trigger the green light"

[@robthemodYT]

I don't know if you ever got the clip Ashley but I sent you a similar clip of the traffic lights failing, but at the junction from the A66 (E) to the A1M

[@laceandwhisky]

Been in this circumstance before and after waiting so long called 101 to let the cops know so they could relay the issue and then I edged out and used it like a normal T junction. Always a gap at some stage 😊

[@martinmb12]

Hi Ashley, I was teaching a pupil on Monday night and she stalled when the lights turned to green and as there wasnt any movement from our lane the lights returned to red and stayed on red for many cycles of the junction and after about 10 mins of continous red light and also with small movements from my pupil and the car behind with still no luck I decided to wait until the junction was empty and guided my pupil through the red light. Im unsure if I made the correct decision in this scenario but we had at least 20+ cars waiting behind and felt that maybe us going through would eventually trigger the lights

[@ibs5080]

Interestingly, in Canada and the USA, the sensors are often loop detectors set in the road surface itself. They detect the metal of a vehicle above them and often there are two or more loop detectors in each lane to give the traffic lights a sense of how long the queue of waiting vehicles is. They can cause issues detecting cyclists and motorcycles but to aid this, they also have an X to mark the spot where a two wheeler should tilt their vehicle to be picked up by the loop detector. Question: Does the UK ever have loop detectors or only the type of sensors as in this video, namely mounted on the traffic lights?

[@thomaselliot2257]

I remember vaguely that Ashley covered those sort of sensors many videos ago . I wonder if he would be able to provide a link . Ashley DID mention it in this video 🙂

[@simoneast757]

I work at Headway Traffic Management and I'm fully qualified in all traffic lights, the simple answer is. On top of the traffic lights is a radar vehicle activation which detects movement, if no movement then the lights will stay red giving the main road green as a priority. In this situation I would of reserved back if I could and drove up to the lights to activate the radar or driven up to the police car, in this video tho the radar seems to be abit dodgy or just simply dirty as dirt can affect the sensor. Theses vehicle activation radars are on all Temporary Lights which I personally put on the road for the last 6 years now, I'm glad that the council are putting these radars on Permanent lights now BUT...the council need to clean them to avoid this problem but they don't. Hope this helps 👍

[@phire0]

As a motorcyclist, occasionally the sensors built into the road do not detect motorbikes so we need to wait there for quite some time for the lights to cycle, but if they don't cycle after some time, then we need to treat it as the lights not working, and according to the highway code, treat it like an unmarked junction and proceed with great care. That would be all well and fine in a situation like in this video, and personally as the police car, I would assume the lights to be not working after some time and would proceed when the road is completely clear, but I have no idea what I'd do at a much busier junction with traffic flowing from different directions.

[@recklessrogue9027]

In my opinion it is definitley down to the lack of decting movement. I have a similar junction in my town and if I approach in my car it is almost always red due to being the least used approach but will change when I pull up. However, at least 50% of the time when on my ebike it doesn't change as I assume it didn't get detected.

[@chrisddr3]

Motorcyclist in NL here. My longest wait was 7 minutes at a light in an eerily empty intersection, ended up running the red. It is quite a common situation, on a bike you need to approach the intersections in the central position of the lane, otherwise the sensor is likely to miss you.

[@imranw4221]

I have this problem in my town in Essex. Best thing to do is if no is behind you then reverse and drive towards the white line to trigger the sensor. Usually works. If that doesn’t work then, I would creep forward if it’s clear in front then go. Better have a dash cam recording just in case you get a ticket. That way you can argue your case.

[@robynrox]

I don't work on these systems but I often see a very small LED light up while I approach temporary lights, and it goes out when I stop before the main, large red light. It has to be sensing movement in my opinion.

[@_.Madness._]

Had the same thing happen at a similar junction last month. The main road lights would go red for pedestrians several times, but our side road light was stuck on red. No one in front had the sense to move their car back and forth to activate the sensors. After a 10-minute standoff, the guy in front had enough and started to make a U-turn and just like that, our light turned green. Next time, I might as well bring a tent and camp out if no one moves.

[@JD-xu1ts]

I had a similar issue with temporary lights and there was que with drivers becoming impatient, in the end very cautiously i had to go through the red light because it seemed to be not working. Just had to make the call on the spot

[@I-Love-Taylor-Swift]

Great vid Ashley. Loved how the police uses his blue lights at the end to deal with the issue.

[@paulgriffiths531]

does flashing your car headlights have any effect (I thinking more of temporarly traffic lights)?

[@bikeman123]

No

[@lukehanna7440]

What I want to know is do the sensors pick up flashing lights as you approach, like can you encourage them to turn green before you reach the lights by flashing your beams?

[@nigelleyland166]

There is another type of light control besides the already menioned motion senor and the loops in the road. On temporary traffic signal ma y be operated amnually, or on set timing, sometines the employ radar which can be seen as abox above the lamp head. It is however not possible as motorist to know which mode is being employed

[@nabilomar4631]

Motorcycle rider - This happens to me all the time with these sensors. Luckily I'm in London so a car is not far behind usually, I normally just pull forward into the cycle box or beyond the white line a little and tell the car behind me to come forward. Lights always change within 10 seconds of this.

[@davet2555]

Used to have this a lot on my old bike and a particular junction. Gave it some time and then treated it as a give way

[@marianbadea369]

Moving the car, like you've said, is the best option and usually does the trick. But they might've been misfunctioning as well because they should've cycled in this amount of time. Or maybe being just a carpark, they were programmed to not cycle. 🤷🏻‍♂️ Some lights are programmed weirdly anyway. I see that at night when I drive a lot with no traffic. Most lights turn green when approached, but some lights, with absolutely no traffic anywhere, they're green continuosly before I approach, can see them from a linf distance, and just as I approach, they turn red. 🙄🤦🏻 Like why!? 🤷🏻‍♂️ My guess is they're programmed intentionally to make you stop because I've seen a lot of lights behave this way. But why when they're supposed to facilitate the flow of traffic, not stop it. Maybe it is to test if you're paying attention or maybe programmed just to get some red light tickets... 🥴 I was wondering if lights can also be controlled manually by someone at a traffic control center or something and they're just playing with people at night! 🤣

[@wintersun398]

I recall an article from the late 90’s saying the traffic light phases in London were modified to make flows less efficient. To purposely slow to flow of traffic. Also induction loops in the roads can be used to calculate traffic speed! If you drive above the speed limit on the approach to some lights they’d turn to red.

[@skypirate4806]

I’ve been in this situation before, it usually ends up either the person at the lights skipping the red light carefully, or if there’s space behind them, they reverse so the sensor picks them up.

[@pqrstzxerty1296]

Atleast the officer realised something is wrong, and then did something about it. I had a simular problem at a roadwork lane closure traffic lights at night, out on a little village lane in nowhere. 15 minutes still red. I phone 999 and police control already knew it was a problem and stated hasn't highways arrrived yet. So police control said to slowly go throu the red, and they are dispatching a police car to the location to deal. Another one happened in my city last week, lane closure traffic lights due to road works. A car crash happened in the queuing traffic. The police had enough and stated to the road construction crew to release the road closure asap as surrounding roads are getting grid locked, which they did for that day.

[@martinbatley9512]

Over the 40 years I've been riding motorcycles I've been stuck at red lights plenty of times due to the underground sensor failing to register my bike. I usually move the bike around trying to trigger the sensor. Failing this I go through on red taking due care. I have actually been caught 4 times by the police going through on red. Fortunately each time I respectfully explained the situation and they recognised I'd taken good care going through. I should mention that each time it's been late at night with little danger .

[@JamesTombs]

Have lights near us that you need to have the front of the car on or slightly beyond the white line to get picked up otherwise traffic going right gets skipped in the light cycle. Many cars, especially learner drivers it must be said, stop a good 5-6ft before the line and end up sitting for a prolonged period through multiple cycles before they get impatient and start creeping forward at which point they'll hit the line and the lights will pick the traffic up. This can cause quite a lot of traffic to build up and someone put up a cardboard sign on the traffic island telling people to make sure there car was forward of the line to stop this happening.

[@leexgx]

Dashcam driver only had to move forward to trigger both the long range IR sensor on the top and the magnetic ground loop sensor (it's about 1 meter by 2 meter in size usually) pay attention to the ground loop lines on the ground make sure you stop on top of them (especially in or just after the white lines in junctions when turning right or they might suddenly change to red without giving you the green arrow) if you zoom in you see them in this video but it isn't very clear (or as your driving around towards traffic lights you see them) the police car and the dashcam driver are not on the magnetic ground loop (the black line box on the arrow) and they stopped on a green/yellow light when it changed to red so the traffic lights are not aware of the standing still traffic (and the longer range IR sensor on the top can't detect non moving traffic) and not all traffic lights have a failsafe timer to force cycle the lights (should be 3 minutes) 3 around where I am where the I have to sometimes tell traffic to move to trigger the ground sensor (people who stop way short of the white line or stop past the white line instead of clearing the lights)

[@bellshooter]

It's a sensor that senses the movement of arriving traffic, Ashley is correct, reverse and re-approach , that will work. We have a set of lights with a right turn filter and road subsurface sensors, if nobody moves forward of the stop line on forward green the filter will not work...

[@MrTangoaddict]

I had a similar experience in the middle of Stratford upon Avon a few weeks ago. I was a few cars back in a traffic queue on a minor road approaching a traffic light controlled crossroads. I could see the lights and they didn’t change from red for over 15 minutes. It’s a horrendous junction in rush hour as traffic on the other side of the crossroads backs up too so there’s often nowhere to go even if the lights are green. I wondered whether they’d stayed on red for that reason. I eventually phoned (hands free!) the police but the lights did eventually change before anyone came out.

[@pgsm15]

Been in this exact situation a light close to home, especially at night behaves this way...so if I there's little traffic I avoid it. How I handle them: 1. Move back and forth if there's space to do so (if this doesn't work) 2. Go through the red light when the otherside has also got a red light, still proceeding slowly and giving them priority at all times

[@benchilcott6908]

I've noticed that in my area, traffic lights on main roads will default to red, while emerging traffic from side roads has green lights. I think this has a similar effect to speed bumps to stop cars absolutely sending it when the roads are empty.

[@robg521]

Same happens down my way outside an international ferry port, when the ferry kick out and the traffic flows everything works great, but if you are only a couple of motor bikes who pull up side by side occasionally this happens, even though you are sitting on top of the road sensors buried under the tarmac for some reason it doesn’t know that you are there, Trying to back up a Harley Davison without a reverse gear is a no go, so you sit for a while they go through the red light when the junction is clear. [luckily its wide open and you can see everything around]

[@adewhite3921]

I've just came across this video and recognised that this is in my local town of Midsomer Norton.These traffic lights and the lights around the corner have always been a problem. On a busy day you have 2 lanes of traffic coming from the left which then have to stop just 10/15 yards past these lights at another set of lights. You only need someone to end up stopping in the box junction in front of these lights to mess everything up as nobody can then pull out when these change to green. By the time the other lights have changed , these will have gone back to red.

[@klapiroska4714]

The traffic light sensors should have some way of detecting traffic waiting at the stop line. I mean, you cannot always guarantee that everyone gets through in one light cycle. I'm not sure how this particular senor exactly works, or how it is programmed, but it could be "watching" the area right behind the stop line. If that is the case, it wouldn't really detect the police car as it is almost completely over the stop line, and it wouldn't detect the viewer as they are still quite far from the stop line. Notice how the pedestrian signal turns red as the viewer crosses the stop line indicating that the traffic light is about to turn green. What might help? Police reversing a bit or the viewer creeping forward a bit might have helped, especially if the sensor is trying to detect if there is something waiting behind the line. Walking between the vehicles might be able to do the trick too. Now the police walked near the pavement, and the system is probably adjusted in a way that it won't confuse someone walking on/near the pavement to an approaching/waiting vehicle. I bet this hadn't happened if the police had not continued past the stop line as their exit was blocked.

[@iallso1]

I have experienced several situations where the sensors in the road have not detected my motorcycle and as a result have failed to cycle. Also several occasions when on busy intersections cars have stopped too far back from the lights and failed to trigger the sensor causing considerable queues.

[@1506Jimbob]

This has happened to me a few times. Need to go back and then forward

[@pajownik]

Happens a lot when you are on a motorcycle. Sensors often don't detect bikes. In many countries The Highway Code allows motorcyclists to proceed with caution. In UK there is no problem, as really important people don't ride motorcycles.

[@shed66215]

There are two different sets in the town where I live where one works relatively well in sensing a cyclist - a T-junction so the lane to turn right is in the middle of the road, the lights are independent so that traffic going left shows green but if no traffic to the right then shows red, with the lights from the left showing green. Only if traffic from the right do the lights then sequence to allow traffic turning to the right but it can change to allow traffic to go straight round without the need to wait for other traffic to change them. The second set is at a crossroads and it can be very frustrating waiting for the lights to either recognise a cyclist is waiting, or having to look over your shoulder to see if a car is approaching that would then change them. Very rarely do they change purely because they sensed a cyclist even when approaching them at a slow speed to allow the sensor time to pick you out.

[@brantnuttall]

I was caught in a similar situation last year. I was coming up a very major road in Blackpool when the traffic lights didn't work. And despite cars and buses queueing up behind me, I sat at the red lights for 3 revolutions (4 way junction). On the 4 revolution though I carefully jumped the red lights and all the following traffic did the same. They were fixed later on that day though.

[@DrBlack1987]

Had same thing happen in my town. After waiting over 5 mins I was about to ask all the traffic to back up so that the cars at the front could move. Is was about 5 cars back so not close enough to tigger the lights myself. In the end the car a the front edged over the red light and into the stationary traffic on the main road. This movement immediately caused the lights to cycle. Lesson is leave some room to to car in front so you can edge forward

[@lolaridgeback5875]

Fair play on the police for helping people get out of the car park.